Fujitsu MB96300 manual Programming the Internal Flash Memory

Page 5

 

 

SK-96370-144PMC-GDC User Guide

 

 

 

Contents

 

 

4.9

Vcc 5 Volts (J4)

28

 

4.10

Vcc 3.3 Volts (J5)

28

 

4.11

Vcc 2.5 Volts (J9)

28

 

4.12

Vcc 1.8 Volts (J10)

28

 

4.13

LIN Bus Inhibit (J6)

28

 

4.14

LIN Bus Inhibit (J11)

28

 

4.15

VCC Connector (J7)

28

 

4.16

GND Connector (J8)

28

5

PROGRAMMING THE INTERNAL FLASH MEMORY

29

 

5.1

Asynchronous Mode

29

 

5.2

Synchronous Mode

31

6

APPENDIX

32

 

6.1

Related Products

32

7

INFORMATION IN THE WWW

33

8

CHINA-ROHS REGULATION

34

9

RECYCLING

36

© Fujitsu Microelectronics Europe GmbH

- 5 -

FMEMCU-UG-960014-10

Image 5
Contents MB96300 Series Revision History Date IssueNo Liability for Consequential Damages Warranty and DisclaimerContents Programming the Internal Flash Memory Abstract OverviewFeatures General Description Emulation System 8 I2C BusEmulator System Do not use any other probe cable than MB2198-507-E only InstallationConnection/Power-On Jumper Description / Function Type Default Coordinates Default Jumper settings for MB96370 SeriesFlash / Lime Jumper SettingsJumper Location Default Jumper SettingsMCU Operating Mode Jumpers and SwitchesOperating Mode S1 Power Supply Configuration Power Supply S2, JP 8, 15, 16, 17JP8 McuvccJP1 Subclock JP 1JP2 JP2Alarm Comparator JP Analog Power Supply Voltage JP 11, 12, 13Alarm Comparator ADC SupplyUart Reset Reset Generation JP 33, 41, 46, 47Reset Connection RST MCUUser Push Buttons User Buttons SW1, SW2, SW3, SW4, SW5, SW6 JP 3, 4, 5, 6I2C pull-up resistor JP 9 LIN-UART 0 JP 19, 21, 23, 25, 27, 28, 29 UART0 SettingsLIN / Uart Can Settings UART2 SettingsLIN-UART 2 JP 36, 37, 38, 39, 40, 42, 43 Can interfaces JP 24, 26, 3411 Flash Configuration Jumpers 10 External Flash ConfigurationExternal Flash memory JP 49, 52 External Sram memory JP 50, 5312 Graphic Display Controller interface GlrstFlrst Power connector ConnectorsMCU pin header connectors X20A, X20B, X21, X22 LIN-UART connectors X5Can Connector Signals Can Connector X6Canl CanhUser LEDs/LCD USER-LEDs & optional LC-Display J1MD0 In-Circuit-Programming ConnectorRstx SIN3VCC Connector J7 Alarm Comparator Connector J2GND Connector J8 External Supply Voltage Vin J3Jumper Settings for Programming via Uart 0 Asynchronous ModeJumper Settings for Programming via Uart 2 Programming the internal Flash memoryFlash Programming Reset optionalJumper Settings for reset signal Flash Programming Socket Synchronous ModeRelated Products AppendixHttp//mcu.emea.fujitsu.com Information in the WWWEvaluation Board Emulation Board China-RoHS regulationTable of hazardous substances name and concentration Valid for European Union Countries RecyclingGültig für EU-Länder