Pioneer EFX-1000 manual Other Troubleshooting

OTHER (TROUBLESHOOTING)

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appliances also in use.

If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.

Symptom		Probably cause			Remedy
No power	÷	Power cord isn’t connected.	÷	Connect power cord to outlet.
No sound, or too low	÷	Connection cords are loose or aren’t con-	÷	Connect properly.
		nected properly.
	÷	Connector terminals and plugs are dirty.	÷	Wipe away dirt and soil.
	÷	Input level is set too low.	÷	Rotate INPUT LEVEL dial toward right
				([MAX] direction).
			÷	Try setting IN&OUT LEVEL switch to the
				opposite position.
	÷	Effect output level is set too low.	÷	Rotate EFFECT OUT LEV. dial toward right
				([MAX] direction).
Analog inputs aren’t output	÷	A digital or EFX LINK input is connected.	÷	Cancel the EFX LINK, and disconnect any
		When analog and digital inputs are connected		digital input with priority over analog
		simultaneously, the digital input is given		inputs.
		priority.		The order of priority of inputs is:
	÷	The DJ mixer (DJM-1000) connected by EFX		EFX LINK > Digital input > Analog input.
		LINK has its effecter link set to ON (EFX LINK).
Digital signals aren’t output.	÷	EFX LINK is connected to DJ mixer (DJM-	÷	If EFX LINK is connected to DJ mixer (DJM-
		1000) via digital link cable.		1000) via digital link cable, ordinary digital
				signals are not output.
				Disconnect the digital link cable.
	÷	The digital output fs setting does not match	÷	Set the digital output fs to match the
		the connected component.		connected component.
When set to BYPASS, analog	÷	No analog inputs are connected.	÷	Use analog signals for input. Or use digital
signals aren’t output.		Even if a digital input or EFX LINK is		output. Outputs when BYPASS is selected
		connected, analog inputs are output as analog		are as follows:
		during BYPASS mode.		Input
				connection	Analog output	Digital output
				conditions
				Analog only	Analog source	Analog source
				Digital only	(no output)	Digital source
				Analog &	Analog source	Digital source
				digital
Effect sounds aren’t applied.	÷	The lever switch is set to [OFF].	÷	Either hold lever switch in [ON] position, or
				set to [ON/LOCK].
	÷	MIX dial is set to [MIN].	÷	Rotate MIX dial toward the right ([MAX]
				direction).
	÷	DEPTH dial is set to [MIN].	÷	Rotate DEPTH dial toward the right ([MAX]
				direction).
	÷	EFFECT OUT LEV. dial is set to [MIN].	÷	Rotate EFFECT OUT LEV. dial toward the
				right ([MAX] direction).
	÷	BYPASS button is ON.	÷	If BYPASS indicator is flashed, no effects
				will be output. Press BYPASS so that the
				indicator goes out.
	÷	EFFECT FREQUENCY indicators (HI, MID,	÷	If EFFECT FREQUENCY indicators are all off,
		LOW) are all off (during use of TRANS,		only the original sound will be output. Press
		FLANGER, FILTER, or PHASER effects).		the button corresponding to the frequency
				band to which you wish to apply effects (the
				button’s indicator will light).
	÷	Some combinations of effects may have weak	÷	Try setting SIGNAL FLOW switch to the
		results. Particularly, some combinations of		opposite position (reverse order of signal
		beat effects and digital jog break may sound		processing for beat effects and digital jog
		weak.		break).
No effect sound is heard when	÷	EFFECT FREQUENCY indicators (HI, MID, LOW)	÷	If EFFECT FREQUENCY indicators are all off,
beat effects are applied.		are all off (during use of DELAY, ECHO, PITCH		no effect sound will be output. Press the
		ECHO effects).		button corresponding to the frequency band
				to which you wish to apply effects (the
				button’s indicator will light).

English

25

<DRB1369>