Pioneer EFX-1000 manual Other Specifications

Page 26

OTHER (SPECIFICATIONS)

Symptom

 

Probably cause

 

Remedy

 

 

 

 

 

When a foot switch is connected,

÷

Foot switch’s logic is reversed (the effector

÷

Use a foot switch with logic matching that

effects are applied even without

 

applies effects when the foot switch is

 

of the effector.

pressing the foot switch.

 

depressed for LOW level).

 

 

 

 

 

 

 

Effect sounds are distorted.

÷

Input level is too high.

÷

Rotate INPUT LEVEL dial toward left ([MIN]

 

 

 

 

direction).

 

 

 

÷

Try setting IN&OUT LEVEL switch to the

 

 

 

 

opposite position.

 

÷

Effect output level is too high.

÷

Rotate EFFECT OUT LEV. dial toward left

 

 

 

 

([MIN] direction).

 

÷

Effect settings are too high (When the DEPTH

÷

Rotate DEPTH dial toward left ([MIN]

 

 

dial is set near its [MAX] position, it may have

 

direction).

 

 

the effect of raising the volume level.)

 

 

 

 

 

 

 

Can’t use EFX LINK function

÷

The digital link cable is not connected.

÷

Connect the digital link cable to a DJ mixer

 

÷ The connected component is not supported.

 

(with digital link support)

 

÷

The DJ mixer’s settings are incorrect

÷

Set the DJ mixer for EFX LINK.

 

 

 

 

 

Can’t use the BPM sync function.

÷

DJ mixer is not connected for EFX LINK.

÷

Connect the DJ CD player and DJ mixer via

 

÷ A DJ CD player with digital link support is not

 

digital link.

 

 

connected to the DJ mixer.

 

 

 

÷

The BPM measurement mode is not set to

÷

Set the DJ effector’s BPM mode to [AUTO].

 

 

[AUTO].

 

 

 

 

 

 

 

Echo sounds are output

÷

During echo effect, if DEPTH dial is set to

÷

Rotate DEPTH dial toward the left ([MIN]

continuously

 

[MAX] and BEAT EFFECTS lever switch is

 

direction).

 

 

moved from [ON] to [OFF], the feedback

 

 

 

 

sound dies not attenuate, producing a hold

 

 

 

 

delay effect.

 

 

 

 

 

 

 

BPM doesn’t count tempo in

÷

Input level is too high, or too low.

÷

Rotate INPUT LEVEL dial so that the input

AUTO mode.

 

 

 

level meter shows around 0 dB.

BPM count is strange.

÷

Some tracks have tempos that prevent them

÷

Set to manual mode and input (TAP) the

 

 

from being measured automatically. (Automatic

 

tempo manually (P.18)

 

 

measurement range is 70-180 BPM).

 

 

 

 

 

 

 

MIDI sequencer isn’t

÷

The MIDI sequencer’s sync mode is not set to

÷

Set MIDI sequencer’s sync mode to

synchronized.

 

“slave”.

 

“slave.”

 

÷

The connected MIDI sequencer is not

÷

A MIDI sequencer without MIDI timing

 

 

supported.

 

clock cannot be synchronized.

 

 

 

 

 

÷This component may fail to operate properly due effects from static electricity or other causes. In this event, try disconnecting the power cord and reconnecting it. If this doesn’t solve the problem, consult your dealer or nearest Pioneer Service Station.

SPECIFICATIONS

1. General

Power supply

AC 110 V - 240 V, 50/60 Hz

Power consumption

16 W

Operating temperature

+5°C to +35°C

Relative humidity

5% to 85% (without condensation)

Weight

2.4 kg

Maximum external dimensions

 

..........................................................

320 (W) x 234 (D) x 101 (H) mm

2. Audio Unit

Sampling rate

96 kHz

A/D, D/A Resolution

24 bits

Frequency characteristics

20 Hz to 22 kHz

S/N ratio

83 dB

Distortion

0.02 %

Headroom

19 dB

Input level

–10 dBV / +4 dBu (22 k)

Output level

–10 dBV / +4 dBu

 

(RCA pin jacks: 1 k, Phone jacks: 1 k)

 

*–10 dBV / +4 dBu is switchable.

3. Input/Output terminals

 

Audio line input terminal

 

RCA pin jacks

2

Phone jacks (1/4-inch/6.3 mm in diameter)

2

Audio line output terminal

 

RCA pin jacks

2

Phone jacks (1/4-inch/6.3 mm in diameter)

2

Digital input terminal

 

RCA pin jack

1

Digital output terminal

 

RCA pin jack

1

EFX LINK connector (mini-DIN)

1

MIDI input terminal (5-pin DIN)

1

MIDI output terminal (5-pin DIN)

1

4. Accessories

 

Operating instructions

1

Digital link cable

1

Power cord

1

NOTE:

Specifications and design are subject to possible modification without notice.

26

<DRB1369>

Image 26
Contents Page Importante Confirm Accessories FeaturesContents BPM Counter Effect TimeBPM Effect Apply the desired effect Digital JOG Break MeterSelect the desired effect Hold buttonConnections Installation LocationCleaning the unit Connection PanelDJ Mixer on DJ mixer provided with Send Connecting the SEND/RETURN Terminals onBasic Connections Return terminalsDJ Mixer DJ CD Player Connecting the power cordEffector EFX-1000 Effects Beat EffectsFilter effect Phaser effectFlanger effect Digital Jog Break Beat effect Effect ParametersEffects Effect Parameters Digital Jog BreakControls and Functions Before USE Controls and FunctionsDELAY, ECHO, Pitch ECHO, TRANS, Flanger FILTER, Phaser Beat Effect sectionDigital Jog Break section ZIP, HUMANIZER, VocoderOperations Character dial Beat Effects BPM modeDepth dial MIX dialUse the Rhythm Mode button to set to rhythm mode Beat Effects Rhythm modeOperations Beat Effects Rhythm mode Press rhythm REC button to set to REC modeOperations Digital Jog Break Jog MemoryHold Function Press the Single or Loop buttonSetting the Receive Midi channel Midi SettingsSetting Transmit Midi channel Midi Implementation Chart Function Transmit Receive CommentsDELAY, ECHO, Pitch Echo Snapshot Program ChangeAbout Rhythm Effects During TransmitTroubleshooting Other TroubleshootingSpecifications Other Specifications