BEFORE USE (CONNECTIONS)
CONNECTIONS
Connection Panel
1 |
|
| 2 | 3 | 4 |
| 5 | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 | 7 | 8 | 9 | 10 |
English
1 Power input socket (AC IN)
Use the provided power cord to connect this socket to an AC outlet.
2POWER switch
3Digital OUTPUT fs SELSECT switch
Use to change the digital output frequency sampling rate (fs) (44.1kHz/48kHz/96kHz).
4 Link input/output connector (EFX LINK)
When the accessory digital link cable is used to connect this connector to the
CAUTION:
The EFX LINK connector is designed to be connected via the provided digital link cable ONLY to a component equipped with the designated digital link function.
The unit may be damaged if this connector is mistakenly connected to any other component.
9 Audio INPUT/OUTPUT jacks
Uses 6.3mm phones plug. For monaural inputs, connect L input channel only for output on both L and R channels. Audio inputs are throughput (output) even when the unit’s power is turned OFF.
10Audio INPUT/OUTPUT jacks
INPUT/OUTPUT connectors using RCA pin jacks.
Audio inputs are throughput (output) even when the unit’s power is turned OFF.
7Before making or changing the connections, switch off the power switch and disconnect the power cord from the AC outlet. This precaution
should also be taken when changing the IN & OUT LEVEL switch and DIGITAL fs SELECT switch.
÷When connections are made to the phone jack inputs and a monaural signal cable is connected to the L (MONO) terminal, inputs can be made to both the L and R channels.
÷After all other connections are made, connect the power cord to a household wall outlet or to the auxiliary AC power takeoff on your amplifier.
5.MIDI input/output connectors (MIDI OUT/THRU,
MIDI IN)
Use to connect the effector to a MIDI component (see page 21).
6Digital input/output connectors (DIGITAL IN,
DIGITAL OUT)
Use to connect the effector to a component provided with coaxial digital input/output connectors.
7 Foot switch jack (FOOT SW)
Can be connected to a ON/OFF type foot switch with 6.3mm phone plug to allow ON/OFF control of effects.
Foot switches are available in several types, including
8Input/output gain select switch (IN&OUT LEVEL)
Use to select the input/output gain
See page 21 for instructions on how to use the MIDI terminals.
CAUTION:
Do not make any connections that may create signal loops as this will cause circuit oscillations which could damage the speakers.
[Example of connections that must not be performed]
¶Do not connect the output of the DJ Mixer to the input terminal of the Effector and the output of the Effector to the input terminal of the same mixer.
¶Do not connect the SEND output of the DJ Mixer to the input terminal of the Effector and the output of the Effector to the input terminal of the DJ Mixer (except for the RETURN terminal).
Installation Location
÷Avoid mounting on top of amplifiers, near spotlights, or other
÷Install this unit as far as possible away from tuners and TV sets. A unit installed in close proximity to such equipment may cause noise or degradation of the picture.
Cleaning the unit
To clean the unit wipe with a polishing or a soft, dry cloth. For stubborn dirt, moisten a soft cloth with a weak solution of neutral detergent (diluted in five to six parts water), wring the cloth well, and wipe away the dirt. Use a dry cloth to wipe the surface dry. Do not use volatile liquids such as
benzene or thinner which will damage to the unit. | 7 |
|
<DRB1369>