Pioneer VSX-9300TX manual Listening in stereo, Listening with headphones, Neo6 Music settings

Page 40

05Listening to your system

Neo:6 Music settings

• Default setting: 2

When listening to 2-channel sources in Neo:6 Music mode, you can adjust the center image to create a wider stereo effect with vocals. Note that this is only available when using a center speaker.

1Press RECEIVER.

2With NEO:6 MUSIC mode active, press EFFECT/CH SEL repeatedly to select CENTER IMAGE.

RECEIVER

EFFECT/CHSEL

+

3Use the +/– buttons to adjust the setting. Adjust the effect from 0 (no effect) to 5 (most prominence given to the center channel).

Adjusting the advanced effect level

• Default setting: 50 (except 5/7CH STEREO: 90)

You can emphasize or reduce the level of the advanced effects as you like. You can set the effect level independently for each mode.

RECEIVER

EFFECT/CHSEL

+

1Press RECEIVER.

2With one of the advanced effect modes active, press EFFECT/CH SEL repeatedly until EFFECT shows in the front panel display.

3Use the +/– buttons to adjust the effect level. The effect level can be adjusted from 10 (min) to 90 (max).

40

Listening in stereo

When you select STEREO or DIRECT, you will hear the source through just the front left and right speakers (and possibly your subwoofer depending on your speaker settings). Dolby Digital and DTS multichannel sources are downmixed to stereo.

STEREO/

DIRECT

While listening to a source, press STEREO/DIRECT for stereo playback.

Press repeatedly to switch between:

STEREO – The audio is heard with your surround settings (such as channel level) and you can still use digital processing (such as the Midnight, Loudness, and Tone control functions).

DIRECT – Bypass all effects and surround settings so that the audio remains as close to the source audio signal as possible.

Note

If you switch on any signal processing features (for example, digital noise reduction or the tone controls) when DIRECT is selected, the receiver automatically switches to STEREO.

Listening with headphones

When headphones are connected, all multichannel sources, as well as all of the MOVIE and MUSIC modes with be downmixed to 2 channels. Two channel sources will be heard in stereo.

Connect a pair of headphones to the PHONES jack on the front panel.

All sources will be heard in stereo (downmixed). When you disconnect them it reverts to the previous mode.

Note

Many receiver features (such as matrix decoding) are not accessible when the headphones are connected.

When headphones are connected, no sound is heard from the speakers. However, sound will still be output from the preouts.

You can only hear the front left and right channels when MULTI CH IN is switched on.

En

Image 40
Contents VSX-9300TX Information to User Risk of Electric Shock Do not OpenImportant Safety Instructions Contents Using other functions Advanced setupControlling other equipment Other connectionsFeatures Checking the supplied accessoriesBefore you start Before you start ChapterUsing the remote control Installing the receiverBefore you start Ventilation Opening the front panelRemote control battery indicator Operating range of the remote controlBefore you start Setting up for Surround Sound Minute guideMinute guide Chapter Introduction to home theater02 5 minute guide Connect your speakersMinute guide Use the on-screen Auto Surround setup to set up your systemLarge Enter ‘Surround Setup’ should be highlighted. Press‘SurrBack System’ should be highlighted. Press Make sure ‘Normal System’ is selected, then select ‘Exit’ ‘Auto Setting’ should be highlighted. PressFollow the instructions on-screen Other problems when using the Auto Surround Setup Checking the settings on your DVD or other playerPlaying a source Connecting your equipment Chapter Connecting your equipmentRear panel Connecting your equipment About the video converterConnecting your equipment About cable types When making cable connectionsAnalog audio cables Digital audio cablesConnecting your equipment Connecting your TV Connecting your equipment Connecting a DVD player DVD playerConnecting the multichannel analog outputs VSX-9300TXSTB Connecting your equipment Connecting a VCR or DVD recorder Connecting your equipment Connecting other video sources Connecting your equipment Using the component video jacks DVD playerConnecting your equipment Connecting digital audio sources Connecting your equipment Connecting analog audio sources Tape deck, etcPortable DVD player, etc Connecting your equipment Installing your speaker system Connecting the speakers Bare wire connectionsPlacing the speakers Banana plug connectionsConnecting your equipment Connecting antennas FM wire antennaConnecting external antennas AM loop antennaPlugging in the receiver Outdoor antenna Indoor antenna Vinyl-coated wire 15-18 ftAbout the AC outlet Controls and displays Controls and displays ChapterSTANDBY/ON StereoControls and displays Controls and displays Display TunedControls and displays Remote control Remote Setup AudioTV Input Movie / MusicListening to your system Chapter Listening to your systemAuto playback Listening in surround sound Listening to your system Movie listening modesBasic modes Advanced effect modesMusic listening modes Dolby Pro Logic IIx Music settingsPro Logic IIx Music See above Listening with headphones Adjusting the advanced effect levelNeo6 Music settings Listening in stereoListening with Acoustic Calibration Listening to your system Selecting the input signal type Press SB CH Mode repeatedly to cycle through Listening to your system Using the surround back channelSurround back channel options Using the audio scaler for Hi-bit and Hi-sampling If you’re using the remote, press ReceiverPress HI-BIT HI-BIT/HI-SAMPLING on the front PanelUsing the tone control Switching the tone control on or offAdjusting the bass and treble Multi CHReducing noise during playback Release the button when you see the setting you wantListening to dual mono soundtracks Using the tuner Using the tuner ChapterTuning directly to a station Finding a stationUsing the tuner MPX modeNaming station presets Listening to memorized station presetsAbcdefghijklmnopqrstuvwxyz Surround Setup menu Surround Setup menu ChapterMaking receiver settings from the Surround Setup menu Select the setting you want to adjustSurround Setup menu Surround back speaker settingNormal surround setting Speaker SettingSelect ‘Channel Level’ from the Normal setup menu Channel LevelSelect ‘Speaker Distance’ from the Normal setup menu Speaker DistanceUsing the remote control with other components Recalling preset codesControlling other equipment Controlling other equipment ChapterProgramming signals from other remote controls Controlling other equipmentControlling other equipment Controls for TVs MenuGuide DiscControlling other equipment Controls for other components SubtitleDisp ModeTOP ExitControlling other equipment Direct function Multi Operation and System OffProgramming a multi-operation or a shutdown sequence Repeat steps 2-4 for as many components as you wantTo add or change a command select ‘Change’ and press Enter Using multi operationsPress Multi Operation Using System off Switching components on and off using the 12 volt triggerOperating other Pioneer components with this unit’s sensor Using other functions Using other functions ChapterAdjusting the delay of a soundtrack Making an audio or a video recordingDimming the display Using other functions Switching the speaker impedance Advanced remote control featuresEditing remote control display names Press the Multi Control button for the componentAdjusting the remote control backlight Using other functionsClearing remote control settings Using other functions Resetting the system Second Zone speaker B setup Switching the speaker systemOther connections Other connections ChapterBi-wiring your speakers Other connections Bi-amping your front speakersBasic multi-room setup SurrBack System multi-room setupOther connections Multi-room listening Making multi-room connectionsUsing the multi-room controls Use the Master Volume dial to adjust the volumeOther connections Press ControlCnnecting additional amplifiers Other connectionsPress Input on the remote control repeatedly to select USB Other connections Using the USB interfaceUSB terminal on the rear panel of this receiver Advanced Mcacc output using your PC Other connections Connecting a PC for Advanced Mcacc outputSelect ‘PC Output’ and press Enter Advanced setup Advanced setup ChapterSystem Setup menu Select the setting you want to adjust then pressAdvanced setup THX Cinema SetupInput Assign menu Assigning the digital inputsFunction Rename Assigning the component video inputsPHONO/LINE Setup Select ‘PHONO/LINE Setup’ from the System Setup menuWhen you’re finished, select ‘Exit’ Select either Phono or LineMulti-Room and IR receiver setup Volt TriggerAdvanced setup Expert setup menu Select ‘Expert’ then press EnterSelect ‘Crossover Network’ from the Expert setup menu Select ‘Fine Channel Level’ from the Expert setup menuAdjust the level of the left channel Crossover NetworkSetting the Acoustic Calibration EQ automatically Fine Channel DelayAcoustic Calibration EQ Setting the Acoustic Calibration EQ manually Select CUSTOM1 Adjust or CUSTOM2 AdjustSelect the channels you want and adjust to your liking Front AlignCopying your Acoustic Calibration EQ settings Checking your Acoustic Calibration EQ settingsSelect ‘DATA COPY’ then press Enter Select ‘DATA CHECK’ then press EnterHow to interpret the graphical output How to use Professional Acoustic CalibrationProfessional Acoustic Calibration Using Professional Acoustic Calibration Select a setup optionSelect ‘Professional’ If you selected ‘Auto Pro.’, select ‘Start’ and pressSelect ‘Bass Peak Level’ from the Expert setup menu Bass Peak LevelChoose the setting that you want Select ‘D-Range Control’ from the Expert setup menuDynamic Range Control Troubleshooting PowerAdditional information Additional information ChapterAdditional information No soundOther audio problems Symptom CauseVideo Audio sources onSettings DisplayRemote control USB interfaceAdditional information Additional information Surround sound formats DolbyAdditional information About THX Additional information Preset code brands DVDCD-R DVRAdditional information Specifications Maintenance of external surfacesOnce you have established a comfortable sound level To establish a safe levelDecibel Level Example Pioneer Corporation