Alesis 15 Storing effects programs, Copying effects programs from one location to another

Page 10

Storing effects programs

After you’ve created a configuration that you like, you can store it for future recall. To store your changes, press the VALUE knob and then turn the knob to select a store location. Press the VALUE knob again to store the program.

Copying effects programs from one location to another

Copying programs is easy. Just call up the program that you want to copy. Then, press the VALUE knob, twist it until you find the location where you want to store your copy, and press VALUE again to store the program in its new location.

Restoring factory defaults for the effect settings

Once you have saved changes to a preset program, you can still recall the original settings. To enter the RESTORE FACTORY PRESETS mode, simply hold down the VALUE knob as you turn the unit on and then select the program to be restored (or AL for all programs). Press the VALUE knob to confirm your selection. The display will blink rapidly several times to indicate the restore was successful. Any program changes you have made will be lost, so you might want to copy the program to another location first.

To exit the RESTORE FACTORY PRESETS mode, just turn the EFFECTS knob. You can also turn the Coolfire off and then on again, without holding down any knobs or buttons, to exit the RESTORE FACTORY PRESETS mode.

Deferred program change

In normal operation, the Coolfire switches immediately to the program you select. However, in some situations — especially when playing live — you may want the ability to scroll through program numbers while remaining in the current program setting. For example, if you’ve got a clean and chorusy rhythm sound stored in program A3, and you want to switch next to a bright lead sound stored in program C5, you don’t want to have to hear all the programs in between. In these cases, use the Coolfire’s Deferred Program Change mode.

While turning on the Coolfire, hold down either one of the Program Up or Program Down buttons. Letters will scroll by on the display, spelling the word “deferred.”

In this mode, you can scroll through program numbers without having the program change each time. When you arrive at a program you want to use, press the Program Up and Program Down buttons or both pedals at the same time in order to switch to that program.

To exit Deferred Program Change mode, turn the Coolfire off, and then turn it back on again without holding down any buttons.

8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de inicio rápido para el usuario Spanish This page intentionally left blank Quick Setup for the Coolfire Front panel operation Rear panel operationExploring the Coolfire’s effects Modifying the effects programsCOMP/LIMIT Compressor/Limiter PlayType guitar modeling EQ Equalizer HUM CancelEdge Noise Gate FX1 Multi-Effect Module 1 Stereo EffectsFX2 Multi-Effect Module 2 Delay/Reverb Effects LevelCopying effects programs from one location to another Restoring factory defaults for the effect settingsStoring effects programs Deferred program changeTuning to a pitch other than A=440 Using the built-in tunerBypassing the effects This page intentionally left blank Manual de inicio rápido para el usuario Español Instalación rápida del CoolfireCómo operar el panel frontal Cómo operar el panel posteriorCómo explorar los efectos del Coolfire Cómo modificar los programas de efectosCOMP/LIMIT Compresión del compresor/limitador Type Tipo modelado de guitarraEQ Ecualizador HPF-High-Pass Filter Filtro pasaaltosNoise Gate Compuerta de ruido HUM Cancel Cancelador de zumbidoFX1 Módulo multiefectos 1 Efectos estéreo FX2 Módulo multiefectos 2 Efectos de retraso/reverberación Cómo guardar efectos de programasCómo copiar programas de efectos de un lugar a otro Level NivelCambio de programa diferido Desviación de los efectosCómo usar el afinador tuner integrado Afinar a un pitch diferente de A=440This page intentionally left blank Page Fonctionnement du panneau avant Fonctionnement du panneau arrièreLa découverte des effets du Coolfire Type modélisation de guitare EQ Égaliseur Edge TranchantÉliminateur DE Bruit Noise Gate Élimination DU Ronflement HUM CancelFX1 Module Multi-Effet 1 Effets Stéréo FX2 Module Multi-Effet 2 Effets de délai/réverbe Copier des programmes deffet dun emplacement à un AutreLa sauvegarde des programmes d’effet Level NiveauModification du programme différé Dérivation des effetsUtilisation de l’accordeur intégré Accorder à un ton autre que A=440This page intentionally left blank Kurzbedienungsanleitung Deutsch Schnellaufbau des CoolfireBedienungselemente Vorderseite Bedienelemente RückseiteProbieren Sie die Effekte des Coolfire aus Verändern von EffektprogrammenTYP modellierende Gitarre EQ Entzerrer NiedrigHUM-CANCEL FX1 Mehrfachwirkmodul 1 StereoeffekteEffektprogramme zwischen Speicherplätzen kopieren FX2 Mehrfachwirkmodul 2 Delay/Reverb EffektProgramme zum Abspeichern von Effekten Level PegelVerzögerter Programmwechsel Verwendung des eingebauten Tuners Umgehen der Effekte AusschaltenTunen auf eine andere Tonlage als A=440 This page intentionally left blank Manuale rapido di utilizzazione Italiano Impostazione rapida CoolfireCaratteristiche pannello anteriore Caratteristiche pannello posterioreEsplorare gli effetti del Coolfire Modificare i programmi degli effettiCOMP/LIMIT Compressore/Limitatore EQ Equalizzatore HPF Filtro passa altoFX1 Modulo multi effetti 1 effetti stereo Memorizzazione di programmi di effetti FX2 Modulo multi effetti 2 effetti delay/reverbCopiare i programmi di effetti da una posizione all’altra Cambiamento di programma differito Deferred program change Ripristino impostazioni predefinite degli effettiBypassare gli effetti Uso del tuner incorporato Accordare ad un pitch diverso da A=440
Top Page Image Contents