Pioneer VSX-D909S manual Press the Control button, Selector

Page 80

Using Other Functions

Using the front panel with the MULTI-ROOM system

	2,4,5	3,4,5	1 Press the MULTI-ROOM & SOURCE
			button.

MULTI-ROOM	INPUT
&SOURCE	SELECTOR

CONTROL
	MASTER
	VOLUME
TUNING +
OL
STATION +
DOWN	UP

The display shown below will illuminate when the receiver is in STANDBY mode.

Also, the MR&S button will light.

2 Press the CONTROL button.

The light will start to blink.

1Ç

3Within ten seconds of step 2, select the FUNCTION with the INPUT

SELECTOR.

For this example we'll use the TUNER function. The display shown below will illuminate.

MULTI-ROOM

&SOURCE

CONTROL

memo	If you don't turn the multi room
	function off you won't be able to turn
	the entire main room system off.

The INPUT SELECTOR steps through the functions in the following order:

DVD/LD TV/SAT CD

VCR 1 TUNER MD/TAPE 1

4Press the CONTROL button again and use the INPUT SELECTOR to adjust the VOLUME. The volume can be adjusted in a range of -82dB

to 0dB.

The display will appear as shown below.

5When in TUNER function, press the CONTROL button and use the INPUT SELECTOR to tune in the

station.

The display will appear as shown below.

Ç

Turn the input selector until you get:

80

Image 80

Contents VSX-D909S For U.S. model Important NoticeFor Canadian model Information to UserImportant Safety Instructions Quick Start Guide Hooking Up Your DVD Player & TVCoaxial Digital Connection Optical Digital ConnectionSetting up the Remote Control & Unit Speaker ConnectionsYou should see the following display on your TV Use the 2 or 3 buttons to choose the DVD/LD settingDigital Input Assignment Playing a DVD with Surround Sound For Better Surround SoundYou should see DVD/LD in the display on the receiver For more information see pagesFeatures Table of Contents Checking the Supplied Accessories How to Use This ManualPreparing the Remote Control Before You StartOpening the Front Panel Installing the ReceiverOperating range of remote control unit Connecting Your Equipment Cassette deck placementAudio Components Analog audio/video cordsDigital Connections Coaxial cords/Optical cablesMemo Example Connection for a DVD/LD or LD playerDigital Input Assignment Connecting DVD/LD players Connecting VCRs or DVRsVideo Components DVD/LD playerSatellite TV Components Digital audio coaxial cords Optical cablesOr standard video cord TV/Satellite tuner5.1 channel analog output jack Multi Channel Input External DecoderComponents equipped with Connecting the Radio Antennas Using external antennasFM wire antenna AM loop antenna Connect an external FM antennaSpeakers Speaker terminalsSpeaker placement Placing Your SpeakersSpeaker impedance First turn the receiver off, then press the STANDBY/ONConnecting Additional Amplifiers PluggingDisplays & Controls Front PanelMulti CH Input See p.40 Tone control buttons Tone buttonChannel Select button Bass -/+ button See p.50Station -/+ Use to choose programmed radio stations Adjusts the overall receiver volumeTuner Control buttons See p.54-57 Display Remote Control Master Volume buttons Input ATT button when USE mode is selectedRemote Setup button when Setup mode is selected System SET UP button when Setup mode is selectedInitial Set Up On Screen DisplaySetting Up for Surround Sound Set the slide switch to SetupPress the System Setup button Speaker Setting See p.32-33Go on to the next page to continue set up Return to the System Setup Menu Digital-In SelectDigital in Select should be selected if it Isnt use the 5´ buttons to select itSelect Small to send bass frequencies to the subwoofer Speaker Setting´ buttons then press the Enter button Menu Setup Menu Select a Test Tone mode Channel LevelWhen you have adjusted each speaker level Press Enter button to return toPrevious screen Select Exit with the 5/ buttons and pressSelect Exit to return to the System Setup Menu Crossover NetworkSelect Crossover Network if Continuing from Channel LEVEL, it willThis completes the speaker setup Bass Peak LevelDefault setting is OFF If listening at loud volumes we recommend turningDynamic Range Control Use the 2 or 3 arrows to choose OFF, MID or MAXChannel Standard modes Basic PlaybackSound Modes Advanced Theater modes MusicalStereo mode DSP modesSelecting a Sound Mode CH SELTurn on the power of the playback Put the remote control slide switch in USEPlaying Sources with Dolby Digital or DTS Sound ComponentPlaying Stereo Sources Switching Analog and Digital Signal Input Lights when a Dolby Digital signal is inputDTS lights when a DTS signal is input Each press switches the signal in the order belowEach press switches Digital NR on or off Reducing Noise During PlaybackDigital input AM/FM tunerListening in Midnight Mode Listening the Loudness ModeEach press switches Midnight Listening mode on or off Press the Midnight buttonAdjusting Bass and Treble Multi Channel in Playback KHz 24 bit PerformancePress the FL Dimmer button Adjusting the Brightness of the DisplayDirect Playback Dual Mono Setting Using the Tuner Automatic and Manual TuningFor Automatic Tuning For Manual TuningExample Direct Access TuningTo cancel before inputting the frequency Memorizing Frequently Used Stations Tune in the desired stationPress the Memory button to activate the memory function Press the Class button repeatedly to select a class numberUsing the remote control Using the front panelRecalling Memorized Stations Use the Number buttons to select the channel you wantSetup Remote Control of Other ComponentsSetting Up the Remote Control to Control Other Components Press the Multi Control button for Component you want to controlPress the 2´3 buttons to choose Function and then press the 5´ buttonsLearning Commands from Other Remote Controls Press the Remote Setup buttonRemote SET UP menu appears on your TV screen Also make sure that your TV is on and set to the receiverPress the button to be programmed Inches 20 cmUsing the Remote Control with Other Components SourceEnter Side A/B = MenuEnter TV/VCR VCR & DVD Recorder OperationsChannel -/+ Press to start recording CD-R only CD & CD-R Player OperationsDisc MD Operations Disc DISP/CHARAExit STB satellite tuner OperationsGuide ÷Á DTV ON/OFF/DTV Menu Disc CH EnterYellow Press to fast forward the tape Cassette Deck OperationsPress to rewind the tape Using Other Functions Recording from Audio ComponentsRecording from Digital Audio Components Recording from Video ComponentsTo cancel here, press Remote Setup Multi OperationsSelect a Multi Control button for this Multi OperationYou can repeat this process for up to five commands Remote sends the Multi Operation commands you pro- grammedPerforming Multi Operations Multi Control buttons start to blinkSystem Off Select a component by pressing its Multi Control button Setting Up the Direct FunctionUsing the System Off Button Resetting the Remote Control Remote Back LightErasing Learned Remote Control Commands Erasing All Learned Commands and Preset CodesVideo Select Set up example Multi-RoomMULTI-ROOM connections Sub room Main roomMULTI-ROOM set up Press System Setup on the remote controlSelect the Volume Level by using the 2´3 buttons Also make sure that the TV is on and set to the receiverSelector Press the Control buttonWithin ten seconds of , select the Function with the Input Using the remote control with the MULTI-ROOM system Press Volume +/- to adjust the volumePress a Function button to select the sub function Receiver from the sub roomPioneer SR System Operating other Pioneer components Techno Tidbits & Problem-solving Dolby DigitalLaser disc format Comparison with Dolby Pro Logic SurroundDevice Preset Code ListDevice Manufacturer Code Troubleshooting Symptom Cause RemedyAnalog DTS Power cord Caution Maintenance of External SurfacesSpecifications Page Page 0 4 2 1 1 4 0