Pioneer VSX-D712 Subwoofer distance setting, Dynamic range control setting, Dual mono setting

Page 49
Subwoofer distance setting

Setting up the receiver

06

Subwoofer distance setting

• Default setting: 10 ft.

Like your speakers, you should set the distance of the subwoofer accurately to hear sounds from all speakers at the same time.

• Use or to set the distance of the subwoofer from the main listening posi- tion (within the range of 0.5 ft. to 45 ft.).

When SW NO is selected in the subwoofer setting, the subwoofer distance can’t be set.

language on one channel and a different language on the other. With this setting you can choose which channel in the dual mono setting you want to listen to.

If Dolby Digital mode is switched on, you will hear the channel you have selected (either ch1 or ch2) through your center speaker. With Dolby Digital mode off, or if you don’t have a center speaker, you will hear the channel you have selected through both front speakers. In the L ch 1.R ch2 setting, the left front speaker will play channel 1 and the right front speaker will play channel 2.

• Use or to cycle through the possible dual mono settings.

Dynamic range control setting

• Default setting: OFF

Dynamic range is the difference between the loudest and softest sounds in any given signal. With this setting, you can compress the dynamic range, so that low level sounds can be heard more easily (sounding relatively louder) yet louder sounds won’t be too over- bearing.

• Use or to set the dynamic range control (OFF, MAX, or MID).

When listening at low volumes, set to MAX for maximum dynamic range compression.

Dynamic range control is effective only when a Dolby Digital or DTS signal is being played back.

L ch 1.R ch2

ch2 ch1

Component video input settings

Here you tell the receiver what components you have hooked up to the component video jacks on the back of the receiver.

Component video 1:

• Default settings: DVD

• Use or to assign the component video 1 input (DVD, TV, VCR or OFF).

Component video 2:

• Default setting: TV

• Use or to assign the component video 2 input (DVD, TV, VCR or OFF).

Dual mono setting

Default setting: ch1

The dual mono setting can only be used when listening to Dolby Digital and DTS signals with dual mono encoding. It is sometimes used when it is necessary to have one

49

En

Image 49
Contents AUDIO/VIDEO MULTI-CHANNELRECEIVER VSX-D712 VSX-D812Operating Instructions Wash hands after handling IMPORTANT NOTICEPage 03 Connecting up Contents06 Setting up the receiver 01 Before you start08 Making recordings 07 Using the tuner09 Controlling the rest of your system 10 Additional informationBefore you start Installing the receiver01Before you start Chapter Checking what’s in the boxBefore you start Operating range of the remote control unit025 minute guide Chapter 5 minute guideIntroduction to home theater Listening to Surround Sound 5 minute guide1 Hook up your DVD player 2 Hook up your TVPowered 025 minute guideFront speakers VSX-D712Front speakers 5 minute guide025 minute guide 6Play a DVD, and adjust the volume to your likingVSX-D812 Surround back speaker or subwoofer2.0ch 5 minute guide Using the Quick Setup3.0ch 7.0ch025 minute guide FWD MID BACKConnecting up Chapter Connecting upAudio/Video cords S-videocablesThis receiver 03Connecting up Connecting digital componentsCD recorder Satellite tuner CD player DVD playerConnecting audio components Connecting upThis receiver CD player CD-R/Tape/MDdeckConnecting DVD multi-channelcomponents 03Connecting upConnecting to the front panel video Connecting video componentsterminal Connecting upFM wire antenna 03Connecting up Connecting antennasUsing external antennas Antenna snap connectorsConnecting up Connecting the speakers VSX-D712ASSIGNABLE FRONTPowered subwoofer 03Connecting up Connecting the speakers VSX-D812Surround speakers Speaker terminals Hints on speaker placementA and B speaker systems Connecting up3-Dview of 5.1 channel speaker setup Overhead view of 5.1 channel speaker setupOverhead view of 6.1 channel speaker setup 03Connecting upOverhead view of 7.1 channel speaker setup 3-Dview of 6.1 channel speaker setup3-Dview of 7.1 channel speaker setup Connecting upVSX-D812 03Connecting up Connecting additional amplifiersVSX-D712 Surround backAC outlet Power cord cautionConnecting up 03Connecting up Operating other Pioneer componentsReceiver Controls and displays Controls and displaysChapter Front panel04Controls and displays See Using the Quick Setup on pageControls and displays Display16Master volume level 15TUNER indicators STEREO04Controls and displays 13ADV.SURR. Advanced Surround13 14 Controls and displays Remote controlFL DIMMER 04Controls and displaysControls and displays D.ACCESS05Playing sources Chapter Playing sourcesIntroduction to Sound Modes Stereo/DirectPlaying sources Choosing the input signalAdvanced Surround modes Neo 6 Music MUSICListening to multi-channelplayback 05Playing sourcesAUTO DVD 5.1 chUsing Advanced Surround Using Stereo/Direct6-STEREO EXPANDED GAMEChannel SB CH 05Playing sources Using the Surround BackSB ON SB OFF SB AUTO VSB ON VSB OFF VSB AUTO Using the Virtual Surround Back mode VSBPlaying sources Using the tone controls Using Midnight and Loudness listeningPlaying other sources MIDNIGHT Off LOUDNESSThe sleep timer switches the receiver into Using the sleep timercontrol to set the sleep timer Selecting the multi-channelanalog inputs06Setting up the receiver Chapter Setting up the receiverChoosing your receiver setup Speaker setting Setting up the receiverSubwoofer setting 06Setting up the receiverSurround back speaker setting Crossover frequency settingLFE attenuator setting Front left speaker distance settingCenter speaker distance setting 100Hz 150Hz 200HzFront right speaker distance setting Surround back speaker distance settingSurround right speaker distance setting Surround left speaker distance settingDynamic range control setting Subwoofer distance settingComponent video input settings Dual mono settingDigital input settings Surround back channel input settingCoaxial digital Optical digitalR C LS SW SB RS Manually calibrating your listening area MCACCSetting up the receiver 06Setting up the receiver L C R RS SW LS SBR C LS SW SB RS The receiver returns to the Standard mode Setting up the receiver07Using the tuner Chapter Using the tunerTuning directly to a station Listening to the radioSaving station presets Using the tunerNaming station presets 07Using the tunerListening to station presets signal The receivers volume, balance, toneMaking recordings Making recordingsSelecting preset codes directly Setting the remote to control other componentsControlling the rest of your system 09Controlling the rest of your system ChapterControlling the rest of your system Clearing all the remote control settingsDirect function Controls for TVs 09Controlling the rest of your systemButtons FunctionButton s Controls for other componentsControlling the rest of your system FunctionButton s 09Controlling the rest of your systemFunction ComponentsSTB SATELLITE Preset Code ListOn digital STB TUNERSONY 09Controlling the rest of your systemYAMAHA 315 , 314 , 328, MD TEACProblem TroubleshootingAdditional information Additional informationProblem 10Additional informationRemedy Additional information Resetting the main unitContinuous power output stereo 10Additional information SpecificationsContinuous power output surround Signal-to-NoiseRatioAM tuner section Cleaning the unitMiscellaneous Furnished parts10Additional information Additional information PIONEER ELECTRONICS USA INC PIONEER CORPORATIONPIONEER ELECTRONICS OF CANADA, INC PIONEER EUROPE NV