Extron electronic VLM 2000, VLM 1000 manual Connect the cables to the receiver

Page 19

2.Connect the cables to the receiver (continued).

b.Install any optional devices and connect their cables to the appropriate ports on the receiver base.

c.If desired, set the Tone and Mix DIP switches on the receiver base.

•Mix (1): Up = Mix auxiliary input and microphone

together on microphone output.

Down = Output the microphone and aux input separately (default).

•Tone (2): Up = Enable the microphone volume change alert tone (default).

Down = Disable the microphone volume change alert tone.

3.Attach the receiver dome to the housing.

a.Locate the locking tab on the receiver dome that contains an arrow etched into its surface.

b.Locate the arrow on the rim of the receiver housing.

OUT IN

	O N
CTS		1
CTS
-2		2

TONE MIX

RS-232 Tx Rx

+ AUXIN

INCTC

NORLY

C

O 1	2
N	Base Plate
CTS-2

TONE

MIX

ÉSet the Tone and Mix DIP switches (optional).

ÑLocatearrow. the locking tab marked with the

ÖLocate the arrow on the housing rim.

VoiceLift Microphone Installation • Installation — Stage 2

2-11

Image 19

Contents VoiceLift Microphone Sicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisFCC Class B Notice VoiceLift Microphone installation and wiring overviewVoiceLift Microphone Installation Introduction Overview Introduction OverviewRoom layout Typical classroom installationVoiceLift Microphone Installation Introduction Planning Introduction PlanningExample of a classroom installation Room configurationRoom considerations  The room is larger than 40 by Introduction Planning, cont’dInventory Introduction Inventory OverviewIncluded items Items not included  Bolts for concrete structural ceilings where neededVoiceLift Microphone Installation Installation Overview Installation OverviewWall or other hard surface Stage 1 Install the VLR 102 Receiver Drop ceilingStage 3 Configure and Test the System Junction boxVoiceLift Microphone Installation Installation Stage Installation StageDrop ceiling Junction box Wall or other hard surface Cut a hole in the ceiling tile Installing the Receiver in a Drop CeilingMount the receiver housing to the ceiling tile Cut a hole in the ceiling tileCAttach a conduit to the back plate if desired Attach a conduit to the back plate if neededAttach a conduit to the junction box if needed Installing the Receiver in a Junction BoxInstall the junction box Attach the receiver housing to the junction boxInstall a raceway if needed Installing the Receiver in a Wall or Other Hard SurfaceMark the mounting screw locations on the surface If not using a raceway Mount the receiver housing to the surfaceIf using a raceway Ethernet cable Where it goes Connects to the PVS 204 SA PoleVault switcherReceiver dome VoiceLift AdapterÇConnect the Ethernet cable to Receiver Out RJ-45 jack Pull the cables to the receiverConnect the cables to the receiver Attach the receiver dome to the housingAlign the arrows on the housing rim and the dome tab Attach the receiver dome to the housingRunpole.the cables through the projector Pull cables to the PoleVault switcherConnect cables to the PoleVault switcher PoleVault switcherTest the system Configure the systemSet up the microphone ÏSet up the microphoneWalk around the room to check for sound quality Finish the installationAdjust the audio level VoiceLift Microphone Installation Installation Stage 3Connect the communication cable to an MLC Digital I/O port Optional Installation Example Instant AlertInsert the black wire into the Ground port Connect the receiver to the MLC 104 IP PlusTest the instant alert notification Configure the MLC 104 IP PlusUsing Global Configurator, configure the MLC’s Press and hold both Volume buttonsVoiceLift Microphone Installation Reference Information Specifications VLR 102 and VLR 102 SRReference Information General Audio/acoustic and electrical Specifications VLP 102 VoiceLift MicrophoneSpecifications VLC 102 Microphone Charging Station Stage 2 Connect the Receiver to the PoleVault System Configure the system. Set up the microphone Test the system.