Extron electronic VLM 1000, VLM 2000 manual Specifications VLP 102 VoiceLift Microphone

Page 28

Installation — Reference Information, cont’d

Specifications — VLP 102 VoiceLift Microphone

Audio/acoustic and electrical

Microphone type

Omnidirectional electret condenser

Microphone gain

-6 dB to +6 dB, adjustable in 1 dB steps

Audio input

Number/signal type

1 mono, via integrated electret condenser microphone or

 

1 mono, unbalanced, via auxiliary mic input jack with 3.3 VDC plug-in power;

 

and

 

1 stereo, unbalanced, via auxiliary line input jack, mixed with mic input

Connectors

(1) 3.5 mm mini audio jack (tip = left, ring = right, sleeve = GND) for

 

auxiliary line input (Audio In)

 

(1) 2.5 mm mini audio jack (tip = signal + bias voltage, sleeve = GND) for

 

auxiliary mic input (Mic)

IR transmitter (microphone transmission)

Signal type

Infrared output

Carrier frequencies

A and C: 2.3 MHz (selectable)

 

B and D: 2.8 MHz (selectable)

Operating range

40' (12.2 m) line of sight

Transmission angles

150° horizontally and 90° vertically

General

Power

Supplied by an internal battery

Charger requirements

+5 VDC, 0.5 A on a 3.5 mm o.d. DC power jack, center pin positive

Batteries

 

Number/type

1 AA size NiMH or alkaline battery

Operating time (h:mm)

Rechargeable 2700 mAh NiMH batteries: up to 8 hours, continuous use

 

Alkaline batteries: up to 8 hours, continuous use

Recharging time

6 hours for a 2700 mAh NiMH battery

Temperature/humidity

Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing

 

Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing

Cooling

Convection, no vents

Mounting

Can be used as a pendant with the included lanyard.

Enclosure type

High impact plastic

Enclosure dimensions

4.7" H x 1.4" W x 1.1" D*

 

(12.0 cm H x 3.5 cm W x 2.9 cm D*)

 

(*Depth includes clip. Depth without clip = 0.9" [2.3 cm])

Product weight

1.7 oz (50 g) without battery

 

2.6 oz (75 g) with battery

Shipping weight

1 lb (<1 kg)

Vibration

ISTA 1A in carton (International Safe Transit Association)

Regulatory compliance

 

Environmental

Complies with the appropriate requirements of RoHS and WEEE.

Accessibility

Section 508 of the Rehabilitation Act (29 U.S.C. 794d)

MTBF

30,000 hours

Warranty

3 years parts and labor

NAll nominal levels are at ±10%.

NSpecifications are subject to change without notice.

2-20 VoiceLift Microphone Installation • Reference Information

Image 28
Contents VoiceLift Microphone Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschVoiceLift Microphone installation and wiring overview VoiceLift Microphone Installation Introduction OverviewIntroduction Overview FCC Class B NoticeTypical classroom installation VoiceLift Microphone Installation Introduction PlanningIntroduction Planning Room layoutExample of a classroom installation Room configurationRoom considerations Introduction Planning, cont’d  The room is larger than 40 byInventory Introduction Inventory OverviewIncluded items  Bolts for concrete structural ceilings where needed Items not includedInstallation Overview VoiceLift Microphone Installation Installation OverviewStage 1 Install the VLR 102 Receiver Drop ceiling Stage 3 Configure and Test the SystemJunction box Wall or other hard surfaceVoiceLift Microphone Installation Installation Stage Installation StageDrop ceiling Junction box Wall or other hard surface Installing the Receiver in a Drop Ceiling Mount the receiver housing to the ceiling tileCut a hole in the ceiling tile Cut a hole in the ceiling tileAttach a conduit to the back plate if needed CAttach a conduit to the back plate if desiredInstalling the Receiver in a Junction Box Install the junction boxAttach the receiver housing to the junction box Attach a conduit to the junction box if neededInstall a raceway if needed Installing the Receiver in a Wall or Other Hard SurfaceMark the mounting screw locations on the surface If not using a raceway Mount the receiver housing to the surfaceIf using a raceway Where it goes Connects to the PVS 204 SA PoleVault switcher Receiver domeVoiceLift Adapter Ethernet cablePull the cables to the receiver ÇConnect the Ethernet cable to Receiver Out RJ-45 jackAttach the receiver dome to the housing Connect the cables to the receiverAttach the receiver dome to the housing Align the arrows on the housing rim and the dome tabPull cables to the PoleVault switcher Connect cables to the PoleVault switcherPoleVault switcher Runpole.the cables through the projectorConfigure the system Set up the microphoneÏSet up the microphone Test the systemFinish the installation Adjust the audio levelVoiceLift Microphone Installation Installation Stage 3 Walk around the room to check for sound qualityOptional Installation Example Instant Alert Insert the black wire into the Ground portConnect the receiver to the MLC 104 IP Plus Connect the communication cable to an MLC Digital I/O portConfigure the MLC 104 IP Plus Using Global Configurator, configure the MLC’sPress and hold both Volume buttons Test the instant alert notificationVoiceLift Microphone Installation Reference Information Specifications VLR 102 and VLR 102 SRReference Information General Specifications VLP 102 VoiceLift Microphone Audio/acoustic and electricalSpecifications VLC 102 Microphone Charging Station Configure the system. Set up the microphone Test the system. Stage 2 Connect the Receiver to the PoleVault System