Extron electronic VLM 2000, VLM 1000 manual Introduction Inventory Overview, Included items

Page 7

Introduction — Inventory Overview

2.Inventory

a.Included items

The VoiceLift Microphone is shipped in one box and is available in two package configurations:

•VLM 1000 (part #42-139-01): one VLP 102 pendant microphone, a VLR 102 Receiver, and a wall charger.

•VLM 2000 (part #42-139-02): two VLP 102 pendant microphones, a VLR 102 Receiver, and a VLC 102 charging station.

Carefully check all the received items against the following inventory lists.

VoiceLift Microphone Devices and Hardware

VLM 1000 VoiceLift Microphone	VLM 2000 VoiceLift Microphone
#42-139-01	#42-139-02

PWR

	Extron	CHARGE
	Extron	ON
		ON
		OFF/MUTE/CHG

VLP 102	VLR 102
Pendant Microphone	IR Receiver

Adapter

Wall Charger/

Power Supply

AA Rechargeable

Battery Lanyard

Z Bracket

and Screw

	15’ Ethernet Cable

VLP 102 Pendant Microphone	Battery, AA 2500mAh
VLR 102 IR Receiver	Lanyard
RJ-45 to C/S adapter	Z bracket
Wall charger/power supply	Z bracket screw
Ethernet cable, 15 ft.

		PWR		PWR
	Extron	CHARGE	Extron	CHARGE
	Extron	ON	Extron	ON
		ON		ON
		OFF/MUTE/CHG		OFF/MUTE/CHG

	VLR 102
VLP 102	IR Receiver
Pendant Microphones (2)

VLC 102	Adapter
VLC 102
Charging Station

ZBracket and Screw

		Lanyard (2)
Wall Charger/
Power Supply	AA Rechargeable
		15’ Ethernet Cable
	Batteries (2)
VLP 102 Pendant Microphones (2)		Ethernet cable, 15 ft.
VLR 102 IR Receiver		Batteries, AA 2500mAh (2)
VLC 102 Charging Station		Lanyard (2)
RJ-45 to C/S adapter		Z bracket
Wall charger/power supply		Z bracket screw

VoiceLift Microphone Installation • Introduction — Inventory Overview

1-5

Image 7

Contents VoiceLift Microphone Sicherheitsanleitungen Deutsch PrecautionsSafety Instructions English Consignes de Sécurité FrançaisFCC Class B Notice VoiceLift Microphone installation and wiring overviewVoiceLift Microphone Installation Introduction Overview Introduction OverviewRoom layout Typical classroom installationVoiceLift Microphone Installation Introduction Planning Introduction PlanningExample of a classroom installation Room configurationRoom considerations  The room is larger than 40 by Introduction Planning, cont’dInventory Introduction Inventory OverviewIncluded items Items not included  Bolts for concrete structural ceilings where neededVoiceLift Microphone Installation Installation Overview Installation OverviewWall or other hard surface Stage 1 Install the VLR 102 Receiver Drop ceilingStage 3 Configure and Test the System Junction boxVoiceLift Microphone Installation Installation Stage Installation StageDrop ceiling Junction box Wall or other hard surface Cut a hole in the ceiling tile Installing the Receiver in a Drop CeilingMount the receiver housing to the ceiling tile Cut a hole in the ceiling tileCAttach a conduit to the back plate if desired Attach a conduit to the back plate if neededAttach a conduit to the junction box if needed Installing the Receiver in a Junction BoxInstall the junction box Attach the receiver housing to the junction boxInstall a raceway if needed Installing the Receiver in a Wall or Other Hard SurfaceMark the mounting screw locations on the surface If not using a raceway Mount the receiver housing to the surfaceIf using a raceway Ethernet cable Where it goes Connects to the PVS 204 SA PoleVault switcherReceiver dome VoiceLift AdapterÇConnect the Ethernet cable to Receiver Out RJ-45 jack Pull the cables to the receiverConnect the cables to the receiver Attach the receiver dome to the housingAlign the arrows on the housing rim and the dome tab Attach the receiver dome to the housingRunpole.the cables through the projector Pull cables to the PoleVault switcherConnect cables to the PoleVault switcher PoleVault switcherTest the system Configure the systemSet up the microphone ÏSet up the microphoneWalk around the room to check for sound quality Finish the installationAdjust the audio level VoiceLift Microphone Installation Installation Stage 3Connect the communication cable to an MLC Digital I/O port Optional Installation Example Instant AlertInsert the black wire into the Ground port Connect the receiver to the MLC 104 IP PlusTest the instant alert notification Configure the MLC 104 IP PlusUsing Global Configurator, configure the MLC’s Press and hold both Volume buttonsVoiceLift Microphone Installation Reference Information Specifications VLR 102 and VLR 102 SRReference Information General Audio/acoustic and electrical Specifications VLP 102 VoiceLift MicrophoneSpecifications VLC 102 Microphone Charging Station Stage 2 Connect the Receiver to the PoleVault System Configure the system. Set up the microphone Test the system.