Extron electronic VLM 1000, VLM 2000 manual Items not included

Page 8

Introduction — Inventory Overview, cont’d

NIf any items in the VoiceLift Microphone boxes are damaged or missing, contact the Extron Technical Hotline (see rear cover for contact numbers).

b. Items not included

The following items are not included. However, some or all of these items may be needed for the installation at your particular site.

•Additional length of RJ-45 cabling (CAT 5, 5e, or 6 with T568A or T568B straight-through wiring)

•Installation hardware (may vary by installation):

Electrical ceiling box, 3.5" or 4.0"

Junction box

Plaster ring

Raceway

Bolts for concrete structural ceilings where needed

Dry wall anchors and screws

Spare ceiling tiles in case of accidental damage during installation

Safety wire, lag eye bolts, and strain reliefs

Heat shrink, extension cord c. Optional items

The optional items suggested below can be added to or substituted for items in the standard VoiceLift Microphone kit.

•VLR 102 SR Secondary VoiceLift Receiver

•VLC 102 Charging Station

•VLP 102 pendant microphone (additional)

•Wall charger

•Headset microphone

•Lapel microphone

•Lanyard

•Lanyard clip

•IPL T S1 Ethernet Control Interface d. Installation tools:

•Tape measure

•Screwdriver set and Tweeker

•Hole saw, keyhole saw, or razor knife

•Appropriate drill and bit set for the mounting surface

•Stud finder

•Flashlight

•Safety goggles

•RJ-45 crimpers and connectors (plenum rated, if applicable)

•Zip ties

•Vacuum cleaner

1-6	VoiceLift Microphone Installation • Introduction — Inventory Overview

Image 8

Contents VoiceLift Microphone Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschVoiceLift Microphone installation and wiring overview VoiceLift Microphone Installation Introduction OverviewIntroduction Overview FCC Class B NoticeTypical classroom installation VoiceLift Microphone Installation Introduction PlanningIntroduction Planning Room layoutRoom considerations Room configurationExample of a classroom installation Introduction Planning, cont’d  The room is larger than 40 byIncluded items Introduction Inventory OverviewInventory  Bolts for concrete structural ceilings where needed Items not includedInstallation Overview VoiceLift Microphone Installation Installation OverviewStage 1 Install the VLR 102 Receiver Drop ceiling Stage 3 Configure and Test the SystemJunction box Wall or other hard surfaceDrop ceiling Junction box Wall or other hard surface Installation StageVoiceLift Microphone Installation Installation Stage Installing the Receiver in a Drop Ceiling Mount the receiver housing to the ceiling tileCut a hole in the ceiling tile Cut a hole in the ceiling tileAttach a conduit to the back plate if needed CAttach a conduit to the back plate if desiredInstalling the Receiver in a Junction Box Install the junction boxAttach the receiver housing to the junction box Attach a conduit to the junction box if neededMark the mounting screw locations on the surface Installing the Receiver in a Wall or Other Hard SurfaceInstall a raceway if needed If using a raceway Mount the receiver housing to the surfaceIf not using a raceway Where it goes Connects to the PVS 204 SA PoleVault switcher Receiver domeVoiceLift Adapter Ethernet cablePull the cables to the receiver ÇConnect the Ethernet cable to Receiver Out RJ-45 jackAttach the receiver dome to the housing Connect the cables to the receiverAttach the receiver dome to the housing Align the arrows on the housing rim and the dome tabPull cables to the PoleVault switcher Connect cables to the PoleVault switcherPoleVault switcher Runpole.the cables through the projectorConfigure the system Set up the microphoneÏSet up the microphone Test the systemFinish the installation Adjust the audio levelVoiceLift Microphone Installation Installation Stage 3 Walk around the room to check for sound qualityOptional Installation Example Instant Alert Insert the black wire into the Ground portConnect the receiver to the MLC 104 IP Plus Connect the communication cable to an MLC Digital I/O portConfigure the MLC 104 IP Plus Using Global Configurator, configure the MLC’sPress and hold both Volume buttons Test the instant alert notificationReference Information Specifications VLR 102 and VLR 102 SRVoiceLift Microphone Installation Reference Information General Specifications VLP 102 VoiceLift Microphone Audio/acoustic and electricalSpecifications VLC 102 Microphone Charging Station Configure the system. Set up the microphone Test the system. Stage 2 Connect the Receiver to the PoleVault System