Extron electronic VLM 1000, VLM 2000 Configure the system, Set up the microphone, Test the system

Page 22

Installation — Stage 3

Stage 3

1. Configure the system.

Follow the steps in your PoleVault installation guide to configure the PoleVault system.

2. Set up the microphone.

(Refer to the VoiceLift Microphone Setup Guide card, provided with your microphone, for details of these procedures.)

a.Set the channels using the rotary switch.

b.Apply the Teacher or Student label to the back of the microphone.

c.Remove the battery door and insert the battery.

d.Attach the lanyard to the rotating clip.

2d

2a

2c

2b

Ç– ÏSet up the microphone.

3.Test the system.

a.Power on all devices. The Power LEDs on the microphone and receiver should light green.

b.Test the microphone for audio. Make sure that the microphone is in the middle of the volume range by pressing the Volume buttons to lower the levels all the way down, then to raise them up six steps.

Volume Up

Volume Down

PWR

ro		CHARGE
Ext	n
	n
		ON
		OFF/MUTE/CHG

Power On/Of

Ñ– ÖTest the microphone for audio.

2-14 VoiceLift Microphone Installation • Installation — Stage 3

Image 22

Contents VoiceLift Microphone Consignes de Sécurité Français PrecautionsSafety Instructions English Sicherheitsanleitungen DeutschIntroduction Overview VoiceLift Microphone installation and wiring overviewVoiceLift Microphone Installation Introduction Overview FCC Class B NoticeIntroduction Planning Typical classroom installationVoiceLift Microphone Installation Introduction Planning Room layoutExample of a classroom installation Room configurationRoom considerations Introduction Planning, cont’d  The room is larger than 40 byInventory Introduction Inventory OverviewIncluded items  Bolts for concrete structural ceilings where needed Items not includedInstallation Overview VoiceLift Microphone Installation Installation OverviewJunction box Stage 1 Install the VLR 102 Receiver Drop ceilingStage 3 Configure and Test the System Wall or other hard surfaceVoiceLift Microphone Installation Installation Stage Installation StageDrop ceiling Junction box Wall or other hard surface Cut a hole in the ceiling tile Installing the Receiver in a Drop CeilingMount the receiver housing to the ceiling tile Cut a hole in the ceiling tileAttach a conduit to the back plate if needed CAttach a conduit to the back plate if desiredAttach the receiver housing to the junction box Installing the Receiver in a Junction BoxInstall the junction box Attach a conduit to the junction box if neededInstall a raceway if needed Installing the Receiver in a Wall or Other Hard SurfaceMark the mounting screw locations on the surface If not using a raceway Mount the receiver housing to the surfaceIf using a raceway VoiceLift Adapter Where it goes Connects to the PVS 204 SA PoleVault switcherReceiver dome Ethernet cablePull the cables to the receiver ÇConnect the Ethernet cable to Receiver Out RJ-45 jackAttach the receiver dome to the housing Connect the cables to the receiverAttach the receiver dome to the housing Align the arrows on the housing rim and the dome tabPoleVault switcher Pull cables to the PoleVault switcherConnect cables to the PoleVault switcher Runpole.the cables through the projectorÏSet up the microphone Configure the systemSet up the microphone Test the systemVoiceLift Microphone Installation Installation Stage 3 Finish the installationAdjust the audio level Walk around the room to check for sound qualityConnect the receiver to the MLC 104 IP Plus Optional Installation Example Instant AlertInsert the black wire into the Ground port Connect the communication cable to an MLC Digital I/O portPress and hold both Volume buttons Configure the MLC 104 IP PlusUsing Global Configurator, configure the MLC’s Test the instant alert notificationVoiceLift Microphone Installation Reference Information Specifications VLR 102 and VLR 102 SRReference Information General Specifications VLP 102 VoiceLift Microphone Audio/acoustic and electricalSpecifications VLC 102 Microphone Charging Station Configure the system. Set up the microphone Test the system. Stage 2 Connect the Receiver to the PoleVault System