Extron electronic VLM 1000, VLM 2000 manual Optional Installation Example Instant Alert

Page 24

Optional Installation Example — Instant Alert

Installation Example — Setting Up an Instant Alert

The following pages describe an example of an optional instant alert setup, in which the relay port of the VLR 102 is connected to a digital I/O port of an Extron MLC 104 IP Plus. This enables e-mail alerts to be sent out when both Volume buttons of the VLP 102 microphone are pressed and held for 3 seconds.

1.Connect the receiver to the MLC 104 IP Plus.

a.Wire one of the provided two-pole captive screw connectors to one end of a communication cable.

b.Plug the communication cable into the receiver’s RLY port.

NIf the MLC controller and the PoleVault switcher are using separate power supplies, ground the

Relay port common pin to the receiver using a jumper between the common pin and the ground pin on either the Contact input, the Aux Input, or the RS-232 port.

ÅConnect a communication cable to the

VLR 102 RLY port.

For separate power supplies, jumper- connect the C pin of the Rly port to the ground pin of the CTC, Aux In, or RS-232 port.

c.Pull the communication cable to the MLC 104 IP Plus location.

d.Connect the other end of the cable to a direct-insertion Digital I/O port on the MLC:

•Insert the black wire into the Ground port.

•Insert the red wire into the first available Digital I/O port.

Û Connect the communication cable to an MLC Digital I/O port.

2-16 VoiceLift Microphone Installation • Optional Installation Example — Instant Alert

Image 24

Contents VoiceLift Microphone Precautions Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschVoiceLift Microphone installation and wiring overview VoiceLift Microphone Installation Introduction OverviewIntroduction Overview FCC Class B NoticeTypical classroom installation VoiceLift Microphone Installation Introduction PlanningIntroduction Planning Room layoutRoom configuration Example of a classroom installationRoom considerations Introduction Planning, cont’d  The room is larger than 40 byIntroduction Inventory Overview InventoryIncluded items  Bolts for concrete structural ceilings where needed Items not includedInstallation Overview VoiceLift Microphone Installation Installation OverviewStage 1 Install the VLR 102 Receiver Drop ceiling Stage 3 Configure and Test the SystemJunction box Wall or other hard surfaceInstallation Stage VoiceLift Microphone Installation Installation StageDrop ceiling Junction box Wall or other hard surface Installing the Receiver in a Drop Ceiling Mount the receiver housing to the ceiling tileCut a hole in the ceiling tile Cut a hole in the ceiling tileAttach a conduit to the back plate if needed CAttach a conduit to the back plate if desiredInstalling the Receiver in a Junction Box Install the junction boxAttach the receiver housing to the junction box Attach a conduit to the junction box if neededInstalling the Receiver in a Wall or Other Hard Surface Install a raceway if neededMark the mounting screw locations on the surface Mount the receiver housing to the surface If not using a racewayIf using a raceway Where it goes Connects to the PVS 204 SA PoleVault switcher Receiver domeVoiceLift Adapter Ethernet cablePull the cables to the receiver ÇConnect the Ethernet cable to Receiver Out RJ-45 jackAttach the receiver dome to the housing Connect the cables to the receiverAttach the receiver dome to the housing Align the arrows on the housing rim and the dome tabPull cables to the PoleVault switcher Connect cables to the PoleVault switcherPoleVault switcher Runpole.the cables through the projectorConfigure the system Set up the microphoneÏSet up the microphone Test the systemFinish the installation Adjust the audio levelVoiceLift Microphone Installation Installation Stage 3 Walk around the room to check for sound qualityOptional Installation Example Instant Alert Insert the black wire into the Ground portConnect the receiver to the MLC 104 IP Plus Connect the communication cable to an MLC Digital I/O portConfigure the MLC 104 IP Plus Using Global Configurator, configure the MLC’sPress and hold both Volume buttons Test the instant alert notificationSpecifications VLR 102 and VLR 102 SR VoiceLift Microphone Installation Reference InformationReference Information General Specifications VLP 102 VoiceLift Microphone Audio/acoustic and electricalSpecifications VLC 102 Microphone Charging Station Configure the system. Set up the microphone Test the system. Stage 2 Connect the Receiver to the PoleVault System