Gemini CDM-3610 manual Functions

Page 5

FUNCTIONS:

9POWER: Turn the CDM-3610 on by pressing the POWER button, pressing the CDM-3610’s POWER button a sec- ond time will turn off the unit.

10DISC TRAY: The DISC TRAY is where the CD is held dur- ing loading, unloading and playback, and holds both 12 cm and 8 cm CD’s. (DO NOT FORCE THE CD TRAY TO CLOSE. EXCESSIVE FORCE WILL DAMAGE THE CD MECHANISM, USE THE OPEN AND CLOSE BUTTONS)

11EJECT BUTTON: Pressing the EJECT BUTTON will open or close the DISC TRAY. The DISC TRAY the will not eject in PLAY mode.

12JOG WHEEL: In SEARCH MODE the JOG WHEEL can be used to search forward or backwards in the music track, as well as for fine adjustments to a CUE point in PAUSE mode. In PITCH BEND mode the JOG WHEEL will func- tion the same as the PITCH BEND allowing you to speed up (FORWARD) or slow down (REWIND) the music clock- wise being (FORWARD) and counter clockwise being (REWIND).

13JOG MODE BUTTON: When the JOG MODE BUTTON is illuminated it indicates the JOG WHEEL is in SEARCH MODE, and when not illuminated it indicates that the JOG WHEEL is in PITCH BEND MODE. When blinking, the JOG WHEEL is in SCRATCH MODE.

14DISPLAY: The DISPLAY shows the track number, pitch value, pitch bend, single, continue (for continuous play), play/pause modes, fast forward/reverse modes, loop mode, reloop mode, PGM, repeat modes, the playback display bar, and three different time displays. These times displays are TIME ELAPSED on the track, TIME RE- MAINING on the disc and TIME REMAINING on the track. Time is measured in minutes, seconds and frames.

15PGM: Allows you to create a set playlist. To program a set list into the CDM-3610 memory, begin by stopping the unit from play and pressing PGM to begin the set list. Select a track by using the track selection rotary to scan to the first track to be placed in the set list. When you have selected the proper track press PGM and the CDM- 3610 will be ready to set your next selection. Repeat the previous steps until you have completed your play list, then press play to begin the set list.

16REPEAT: Press the repeat button once to engage 1 or repeat the selected track. Press REPEAT again to en- gage the ALL setting, which will repeat all the tracks on the CD. Press REPEAT again to disengage the repeat function

17SINGLE: Pressing the SINGLE button engages SINGLE mode, in this mode the CDM-3610 will play one song and then stop. Pressing the SINGLE button again will then

CDM-3610

activate CONTINUOUS mode causing the unit to play con- tinuously (after the last track, the unit will return to the first track of the disc and continue to play).

18TIME: The TIME button switches the time display between three available sources, these three are TIME ELAPSED on the track, TOTAL REMAIN on the disc and REMAIN on the track. TIME ELAPSED indicates how much time has currently gone by since the play button was pressed, TO- TAL REMAIN will count down the time remaining on the entire disc and REMAIN counts down the time that is left before the end of the track.

19PITCH: Hold the PITCH button to activate the PITCH CON- TROL SLIDE. Press the PITCH button to switch between 4%, 8%, and 16% pitch ranges that can be controlled via the PITCH CONTROL SLIDER. Hold the PITCH button again to deactivate this mode.

20PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE up or down will change the pitch percentage +/ - 4, 8, or 16%.

21PITCH BEND: Pushing the PITCH BEND BUTTONS will au- tomatically raise the pitch up to +16% or lower the pitch down to -16% from the existing pitch setting. Releasing the buttons will return the pitch to the original pitch set- ting. You can use this function to match the beat when mixing from one song to another.

22LOOP SECTION: A LOOP repeats the section between the entry point (IN) and the exit point (OUT).

A.To set a loop while the unit is playing, start by press- ing the IN BUTTON (it will light up)

B.When you reach the desired end loop point press the OUT BUTTON (it will also light up). The loop will con- tinue playing until you press the OUT BUTTON again allowing the music to continue from that point on.

C.To re-engage the loop you must press the RELOOP BUTTON.

D.When you have released your loop the OUT BUT- TON will turn OFF and the IN BUTTON will remain lit to indicate that your loop is stored in the CDM-3610 memory.

E.Pressing the IN BUTTON again while the unit is playing will erase the previously saved loop while sav- ing your new loop entry point.

F.Press OUT to exit the loop and save a new complete loop.

G.Press RELOOP to return to the beginning of the pre- viously saved loop from normal play. Press RELOOP repeatedly to cause the loop to stutter.

NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT POINT, WHILE ALL OTHERS WILL BE SEAMLESS.

23PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON

5

Image 5
Contents CDM-3610 Grounding or Polarization CDM-3610 Safety Specifications FeaturesPrecautions IntroductionFunctions Mixer Section Specifications Fader ReplacementTroubleshooting Riesgo DE Shock Electrico no Abrir POR Favor LEAImportantes DE Seguridad Conexiones CaracteristicasEspecificaciones DE Seguridad Tiempo Restante DEL DISCO. Tiempo Transcurri FuncionesControles Pausa Seccion DE MixerReloop Specificaciones Resolucion DE ProblemasReemplazo DEL Atenuador Choc Caracteristiques Specifications LaserMises EN Garde ConnexionsPotentiometre DE Reglage DE Vitesse Pitch FonctionsTemps Ecoule Temps Restant Temps Total Restant Microphone Section Console DE MixageLOW, Medium MID & Haigu High Caracteristiques Techniques Remplacement DU CrossfaderDysfonctionnements Achtung Eigenschaften EinleitungSicherheits Informationen VorsichtsmassnahmenBedienoberfläche Mixer Sektion Technische Daten Fader AustauschenFehlerbeseitigung Page Warrant Y and Repair GCI Technologies Corp All Rights Reserved