Gemini CDM-3610 manual Fader Replacement, Troubleshooting, Specifications

Page 7

from end to end can be purchased from your local GEM- INI dealer.

NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE FADER BACK AND FORTH. PRESSING DOWN ON THE CONTROLS CAN BEND CONTACTS AND CAUSE A LOSS OF SOUND.

FADER REPLACEMENT:

1.UNSCREW THE FADER SCREWS. DO NOT TOUCH IN- SIDE SCREWS CAREFULLY REMOVE OLD CROSS FAD- ER AND UNPLUG CABLE.

2.PLUG IN THE NEW CROSS FADER INTO CABLE AND PLACE BACK INTO MIXER.

3.SCREW THE CROSS FADER TO MIXER WITH THE FADER PLATE SCREWS

4.REPLACE THE FACE OF THE MIXER AND SCREW THE FOUR SCREWS BACK IN AND REPLACE THE FADER KNOBS.

TROUBLESHOOTING:

-If a disc will not play, check to see if the disc was loaded correctly (label side up). Also check the disc for exces- sive dirt, scratches, etc.

-If the disc turns but there is no sound, check the cable connections, if they are ok, check your amplifier or re- ceiver.

-If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many CD’s are recorded out of spec and will skip on most or all CD players. Before sending the unit for repair, try playing a CD that you are sure plays properly.

SPECIFICATIONS:

GENERAL:

Type

Compact Disc Player

Disc Type

Standard Compact discs (12 cm & 8 cm)

Time Display

Track Elapsed, Track Remain, or Total remain

Variable Pitch

± 16% Slider with Resume Switch

Pitch Bend

± 16% Maximum

Instant Start

Within 0.03 seconds

Installation

19” each

Dimensions

19” x 4.3” x 10.2” (482 x 110 x 260 mm)

Weight

Main unit: 12.13 lbs. (5.5 kg)

AUDIO SECTION:

Quantization

1 Bit Linear/Channel, 3 Beam Laser

Oversampling Rate

8 Times

Sampling Frequency

44.1 kHz

Frequency Response

20 Hz to 20 kHz

Total Harmonic Distortion

Less Than 0.05%

Signal to Noise Ratio

85 dB

Dynamic Range

85 dB

Channel Separation

85 dB (1 KHz)

CDM-3610

Output Level

2.0 +/- 0.2V R.M.S.

Power Supply

AC 115/230V, 60/50 Hz

INPUTS:

Phono

............................................................................3mV,47 KOhm

Line

150 mV, 27 KOhm

MIC

1.5 mV, 1 KO balanced

OUTPUTS:

Max

20V Peak-to Peak

Rec

225 mV, 5 KOh

S P E C I F I C AT I O N S A N D D E S I G N A R E S U B J E C T T O C H A N G E W I T H O U T N O T I C E F O R P U R P O S E O F I M P R O V E M E N T.

7

Image 7
Contents CDM-3610 Grounding or Polarization CDM-3610 Introduction FeaturesSafety Specifications PrecautionsFunctions Mixer Section Troubleshooting Fader ReplacementSpecifications Importantes DE Seguridad POR Favor LEARiesgo DE Shock Electrico no Abrir Especificaciones DE Seguridad CaracteristicasConexiones Controles FuncionesTiempo Restante DEL DISCO. Tiempo Transcurri Reloop Seccion DE MixerPausa Reemplazo DEL Atenuador Resolucion DE ProblemasSpecificaciones Choc Connexions Specifications LaserCaracteristiques Mises EN GardeTemps Ecoule Temps Restant Temps Total Restant FonctionsPotentiometre DE Reglage DE Vitesse Pitch LOW, Medium MID & Haigu High Section Console DE MixageMicrophone Dysfonctionnements Remplacement DU CrossfaderCaracteristiques Techniques Achtung Vorsichtsmassnahmen EinleitungEigenschaften Sicherheits InformationenBedienoberfläche Mixer Sektion Fehlerbeseitigung Fader AustauschenTechnische Daten Page Warrant Y and Repair GCI Technologies Corp All Rights Reserved