Compex Systems AP4530 manual Checking the iDR-8 Operating Code Version

Page 17

Checking the iDR-8 Operating Code Version

A&H iDR

V3.00

<

scroll

 

 

<

>

 

 

 

ESC

 

ENTER

MENU

With the face plate removed, press and hold the ESC key to view the current version of operating code running in the unit.

Check that this code is the same version as the iDR System Manager software you have installed on your PC. View this by clicking on the software Help menu About item. If it is an older version then carry out the code update procedure described below. If you have several units connected over a network make sure you check each for the correct version number.

We recommend that you check the Allen & Heath web site for the latest version of software. Download and install this if it is different to that already on your PC.

Updating the iDR-8 Operating Code

IMPORTANT: Make sure all iDR units to be controlled by the PC are running the same version software as installed on the PC.

HyperTerminal settings If you prefer to use an alternative terminal or communications program, or you wish to configure the HyperTerminal connection manually, the required port settings are:

Baud Rate

115200

Data bits

8

Parity

none

Stop Bits

1

Flow Control

None

Protocol

1K Xmodem

DR Boot

V1.00

Update

 

CODE UPDATE

FRONT/REAR

active

RS232

For connection to PC com port

Boot code is the built-in software used by the iDR-8to manage its operating code. It lets the unit communicate with your PC when performing code updates. It is permanently stored and cannot be updated by the user.

The operating code is held in non-volatile memory within the iDR-8unit. It is the software which runs the unit once it is configured.

The front panel RS232 port is provided for updating the unit operating code from a binary file on the PC. This is done using the Windows™ HyperTerminal application which sends the file to the iDR via the PC RS232 serial port. The file is provided with the iDR System Manager software.

Make sure your PC has the Windows™ HyperTerminal application installed and an available COM1 or COM2 port. Use a standard male to female RS232 lead such as the one supplied with the unit. Do not use a null modem cable.

Refer to any Release Notes which may apply. We recommend that you archive the current configuration before you start the update if the iDR-8has settings you wish to keep. Further information is provided in the iDR System Manager Help file.

1Start HyperTerminal From the Start / Programs / Allen & Heath / iDR System Manager menu select the Update iDR Unit Software (COMn) item. Select the COM1 or COM2 version as appropriate for your PC. The HyperTerminal window is opened.

2Select the file to transfer From the Transfer menu select the Send File item. Click on the Browse button. The file named ‘iDR Unit Software V3_nn.bin’ is displayed. Make sure the version number is the same as the one you want to load. Open the file. The Send File window is opened ready to send the file via the COM port. Do not do this until you have prepared the iDR-8.

3Prepare the iDR-8With the face plate removed, plug one end of the RS232 lead into the appropriate PC COM port. Plug the other end into the iDR-8front RS232 port. Press the FRONT/REAR switch so that the green ACTIVE indicator next to the port lights. Now press the CODE UPDATE switch. The LCD displays the boot code version number and ‘Update...’.

4Start the file transfer Click on the HyperTerminal Send button. The transfer starts and a window displays information and a progress bar. The LCD displays ‘Updating…’ progress and then ‘Update Complete’. The process can take a few minutes.

5Restore normal operation Exit HyperTerminal. Deselect the CODE UPDATE switch. The unit reboots automatically. Deselect the FRONT/REAR switch if you want the rear RS232 port to become active. Press ESC to confirm that the correct version of operating code has been loaded.

iDR-8User Guide

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents IDR-8 Conditions Of Warranty Limited One Year WarrantyImportant Mains Plug Wiring Instructions Important Safety Instructions Read FirstThis appliance must be earthed IDR-8User GuideIntroduction Contents DR-8 Welcome to the iDR-8IDR-8 main processing unit 2U, 8 mic/line Main FeaturesDaisy chain iDR-8 units Any number may be Stereo audio monitor with front panelExpander status LEDs These display Front Panel OverviewFront panel RS232 port This is used for Monitor in L Monitor OUT L Rear Panel OverviewSystem Processing Overview IDR-8User Guide Page IDR System Manager Software Bundle Getting Started Check the ContentsIDR-8 Main Unit Installing the iDR-8Earthing Turning the iDR-8 On and Off Parameters restored on power-up The iDR-8Starting Offline with iDR System Manager Software Updating the iDR-8 Operating Code Checking the iDR-8 Operating Code VersionPPP Setup IDR-8 Setup MenusChecking the Current Settings and Status Accessing the iDR-8 Setup MenusRebooting the iDR-8 Changing the Unit NameDR-8 Getting Started Checking the HardwareRS232 COM Port Communicating with the iDR-8Network Port Communicating Using a TCP/IP Connection Connecting the iDR-8 to a Network Connecting the iDR-8 Direct to the PCHow to get the MAC address Connect the PC to the iDR-8 Plug the PC Ethernet portSetting up a Dial-up Connection Communicating Using a Dial Up ConnectionChanging the iDR-8 PPP settings Go to menu *6 PPP Setting up the PC dial-up connection You needDial up the iDR-8 using the remote PC Open up Connecting the iDR-8 to a ModemStarting the iDR System Manager Connect the iDR-8 to the modemArchiving and Loading Configurations Setting the Time and Day ClockWorking with the iDR System Manager Start the iDR System Manager from the Start / ProgramsInput Source window From within the Input XLR Analogue Inputs and OutputsMonitor TRS Input and Output The monitor is Monitor Headphones Output This followsMonitor Inputs and Outputs Daisy chaining iDR-8 monitors The active Using the Monitor as Additional ChannelsCheck the connections The iDR-inAUDIO OUT Adding the iDR-in and iDR-out Audio ExpandersTurning the expander on or off Turn the unit on Checking for expanders You can use the frontExpanded multiple iDR-8 system This diagram Slave Linking iDR-8 UnitsUnit a Connecting to the iDR-8 The iDR-8communicates Adding the iDR-switch ExpanderChecking for iDR-switch expanders You can Using the switch closure inputs The input is Connectors and grounding Pluggable PhoenixUsing the logic outputs Each output is opto Selecting the Communications Options Click on MIDI, SysNet and PL-Anet PortsSysNet IDR-8 Memory System IDR-8 unit settings These areConfiguration file settings These are Only store the parameters you need For your Starting with the PatchesDecide your system starting point Assign DR-8 Technical SpecificationDR-8 ApplicationIDR-switch Front Panel IDR-8 Installer Front PanelHeadphones DescriptionIDR-switch Logic Outputs IDR-switch InputsPower Supply Network PortSoftware Soft SwitchesClock NamingSignal Generator DelayLevel Control Fader GroupsFactory default patch parameters Factory default unit settingsFactory default configuration settings Template for Allen & Heath iDR-8 Front Panel Key Label
Top Page Image Contents