Compex Systems AP4530 manual Factory default unit settings, Factory default configuration settings

Page 46

Factory default unit settings

Unit name – iDR Unit Name Network settings

DHCP – No

IP address – 192.168.0.1 Net mask – 255.255.255.0

PPP settings

Host IP address – 192.168.0.1 Client IP address – 192.168.0.2 User name – iDR

Password – A&H

Factory default configuration settings

Input channel names

I/P 1…. I/P 16

Output channel names

O/P 1…. O/P 16

Input group names

IP Grp 1…. IP Grp 8

Output group names

OP Grp 1…. OP Grp 8

Stereo selections

All mono

Communications option

A RS232 B SysNet

Scheduled events

None

Power-up patch

None

All patches empty

Factory default patch parameters

AMM

No active inputs No active outputs Threshold 7dB Gate depth 40dB Hold time 1s

NOM attenuation 3dB Input delays

All 0ms

Output delays All 0ms

Input faders, mutes, groups Fader levels off Mutes off

Group assignments none Group levels 0dB

Input patchbay

XLR 1 to Channel 1….

XLR 8 to Channel 8 Expander 9 to Channel 9….

Expander 16 to Channel 16

Output patchbay

Channel 1 to XLR 1….

Channel 8 to XLR 8 Expander 9 to XLR 9….

Expander 16 to XLR 16

LCD

Line 1 – user text ‘Allen & Heath’ Line 2 – time

Mic preamps Pad on

Gain +20dB (resulting gain 0dB)

+48V off Limiter off

Monitor manager

Follow mouse / active window Routing matrix

All cross points 0dB (on) Signal generator

Signal type – sine wave Frequency – 440Hz Level - -30dB

Front panel soft keys

S1-S8 – input level control CH1-8

S9-S16 – output level control CH1-8 iDR-switch inputs

S1-S24 – unused

Front panel soft LEDs

L1-L16 – static LED off

L17-L24 – input source meters CH1-8

L25-L32 – output post limiter meters CH1-8 iDR-switch outputs

S1-S16 – static LED off Input expander

S1-S8 – input source meters CH9-16 Output expander

S1-S8 – Output post limiter meters CH9-16

46	IDR-8User Guide

Image 46

Contents IDR-8 Limited One Year Warranty Conditions Of WarrantyThis appliance must be earthed Important Safety Instructions Read FirstImportant Mains Plug Wiring Instructions IDR-8User GuideIntroduction Contents Welcome to the iDR-8 DR-8Daisy chain iDR-8 units Any number may be Main FeaturesIDR-8 main processing unit 2U, 8 mic/line Stereo audio monitor with front panelFront panel RS232 port This is used for Front Panel OverviewExpander status LEDs These display Rear Panel Overview Monitor in L Monitor OUT LSystem Processing Overview IDR-8User Guide Page Getting Started Check the Contents IDR System Manager Software BundleInstalling the iDR-8 IDR-8 Main UnitEarthing Starting Offline with iDR System Manager Software Parameters restored on power-up The iDR-8Turning the iDR-8 On and Off Checking the iDR-8 Operating Code Version Updating the iDR-8 Operating CodeIDR-8 Setup Menus PPP SetupRebooting the iDR-8 Accessing the iDR-8 Setup MenusChecking the Current Settings and Status Changing the Unit NameGetting Started Checking the Hardware DR-8Network Port Communicating with the iDR-8RS232 COM Port Communicating Using a TCP/IP Connection How to get the MAC address Connecting the iDR-8 Direct to the PCConnecting the iDR-8 to a Network Connect the PC to the iDR-8 Plug the PC Ethernet portChanging the iDR-8 PPP settings Go to menu *6 PPP Communicating Using a Dial Up ConnectionSetting up a Dial-up Connection Setting up the PC dial-up connection You needStarting the iDR System Manager Connecting the iDR-8 to a ModemDial up the iDR-8 using the remote PC Open up Connect the iDR-8 to the modemWorking with the iDR System Manager Setting the Time and Day ClockArchiving and Loading Configurations Start the iDR System Manager from the Start / ProgramsXLR Analogue Inputs and Outputs Input Source window From within the InputMonitor Inputs and Outputs Monitor Headphones Output This followsMonitor TRS Input and Output The monitor is Using the Monitor as Additional Channels Daisy chaining iDR-8 monitors The activeTurning the expander on or off Turn the unit on Adding the iDR-in and iDR-out Audio ExpandersCheck the connections The iDR-inAUDIO OUT Checking for expanders You can use the frontExpanded multiple iDR-8 system This diagram Linking iDR-8 Units SlaveUnit a Checking for iDR-switch expanders You can Adding the iDR-switch ExpanderConnecting to the iDR-8 The iDR-8communicates Connectors and grounding Pluggable Phoenix Using the switch closure inputs The input isUsing the logic outputs Each output is opto SysNet MIDI, SysNet and PL-Anet PortsSelecting the Communications Options Click on Configuration file settings These are IDR-8 unit settings These areIDR-8 Memory System Decide your system starting point Assign Starting with the PatchesOnly store the parameters you need For your Technical Specification DR-8Application DR-8Headphones IDR-8 Installer Front PanelIDR-switch Front Panel DescriptionPower Supply IDR-switch InputsIDR-switch Logic Outputs Network PortClock Soft SwitchesSoftware NamingLevel Control DelaySignal Generator Fader GroupsFactory default configuration settings Factory default unit settingsFactory default patch parameters Template for Allen & Heath iDR-8 Front Panel Key Label