Compex Systems AP4530 manual Description, IDR-8 Operator Front Panel, IDR-8 Installer Front Panel

Page 42

Description

iDR-88 mic/line in 8 line out main processor iDR-in8 mic/line in audio expander iDR-out8 line out audio expander iDR-switch24 switch, 16 logic output expander PL Range of wall plates and remote controllers

iDR-8 Operator Front Panel

Face plate fitted

2x16 character assignable backlit LCD display

16x installer assigned soft keys

2x scroll keys

32x installer assigned 3-colour soft LEDs Headphones socket with recessed level trim Key function label protected by window

iDR-8 Installer Front Panel

Face plate removed (4x 2mm hex screws) Setup keys – menu, enter, esc, scroll up/down

Menu items – patch select, clock, day, unit name, network setup, PPP setup, audio monitor, diagnostics

Status LEDs – slave, ext sync lock, 96kHz RS232 – for connection to PC COM port Front/rear RS232 port select switch Code update mode switch

Ident strip – for installer fitted custom label

iDR-in, iDR-out Front Panels

Status LEDs – link, lock, power

8x installer assigned 3-colour soft LEDs

iDR-switch Front Panel

Status LEDs – link, power

DSP

2x Motorola 24bit processors, 56bit mix accumulator Selectable 48kHz or 96kHz sample rate

Audio matrix (48kHz) 16x16 Audio matrix (96kHz) 8x8

Latency XLR in to XLR out with processing <2.3ms

A/D Converters

24bit resolution

Dynamic range 109dB A-weighted, 106dB unweighted

D/A Converters

24bit resolution

Dynamic range 115dB A-weighted, 112dB unweighted

Performance

Frequency response 20Hz-20kHz +0/-0.5dB Crosstalk <-80dB @ 1kHz, 0dB gain THD+noise <0.01% @ 1kHz, 0dBu Residual output noise <-93dBu

Input to output noise @ 0dB gain <-87dBu

Input to output noise @ 50dB gain <-73dBu

42

Mic/Line Inputs x8 (x16 expanded)

Female 3pin XLR

Electronically balanced, pin 2 hot

Impedance 2k ohm (pad out), >10k ohm (pad in) Gain range -15 to +50dB in 3dB steps

Pad -20dB

Sensitivity (pad out) -50 to -5dBu Sensitivity (pad in) -30 to +15dBu Maximum input level +33dBu

Pre converter soft limiter -4dBFS, switchable Phantom power +48V DC switched

Line Outputs x8 (x16 expanded)

Male 3pin XLR

Electronically balanced, pin 2 hot

Impedance <75 ohms

Maximum output +18dBu

Expander Input Port

RJ45 connector

Proprietary 8 channel digital audio

From iDR-inaudio expander

CAT5 STP cable up to 250 metres (825 feet)

Expander Output Port

RJ45 connector

Proprietary 8 channel digital audio

To iDR-outaudio expander

CAT5 STP cable up to 250 metres (825 feet)

Stereo Monitor Inputs

Ripple through audio monitor

Can be assigned as extra channel inputs

Separate L and R TRS jacks

Electronically balanced, tip hot

Impedance >30k ohm

Sensitivity 0dBu

Maximum input +18dBu

Stereo Monitor Outputs

Line output from active monitor bus

Can be assigned as extra output channels

Separate L and R TRS jacks

Electronically balanced, tip hot

Impedance <75 ohms

Normal output 0dBu

Maximum output +18dBu

Headphones

Stereo output on TRS jack

Tip left, ring right

For headphones >30 ohms impedance

Front panel recessed level trim

Adjust with flat bladed screwdriver

IDR-8User Guide

Page 41 Page 43
Image 42
Page 41 Page 43
Contents IDR-8 Limited One Year Warranty Conditions Of WarrantyThis appliance must be earthed Important Safety Instructions Read FirstImportant Mains Plug Wiring Instructions IDR-8User GuideIntroduction Contents Welcome to the iDR-8 DR-8Daisy chain iDR-8 units Any number may be Main FeaturesIDR-8 main processing unit 2U, 8 mic/line Stereo audio monitor with front panelFront Panel Overview Front panel RS232 port This is used forExpander status LEDs These display Rear Panel Overview Monitor in L Monitor OUT LSystem Processing Overview IDR-8User Guide Page Getting Started Check the Contents IDR System Manager Software BundleInstalling the iDR-8 IDR-8 Main UnitEarthing Parameters restored on power-up The iDR-8 Starting Offline with iDR System Manager SoftwareTurning the iDR-8 On and Off Checking the iDR-8 Operating Code Version Updating the iDR-8 Operating CodeIDR-8 Setup Menus PPP SetupRebooting the iDR-8 Accessing the iDR-8 Setup MenusChecking the Current Settings and Status Changing the Unit NameGetting Started Checking the Hardware DR-8Communicating with the iDR-8 Network PortRS232 COM Port Communicating Using a TCP/IP Connection How to get the MAC address Connecting the iDR-8 Direct to the PCConnecting the iDR-8 to a Network Connect the PC to the iDR-8 Plug the PC Ethernet portChanging the iDR-8 PPP settings Go to menu *6 PPP Communicating Using a Dial Up ConnectionSetting up a Dial-up Connection Setting up the PC dial-up connection You needStarting the iDR System Manager Connecting the iDR-8 to a ModemDial up the iDR-8 using the remote PC Open up Connect the iDR-8 to the modemWorking with the iDR System Manager Setting the Time and Day ClockArchiving and Loading Configurations Start the iDR System Manager from the Start / ProgramsXLR Analogue Inputs and Outputs Input Source window From within the InputMonitor Headphones Output This follows Monitor Inputs and OutputsMonitor TRS Input and Output The monitor is Using the Monitor as Additional Channels Daisy chaining iDR-8 monitors The activeTurning the expander on or off Turn the unit on Adding the iDR-in and iDR-out Audio ExpandersCheck the connections The iDR-inAUDIO OUT Checking for expanders You can use the frontExpanded multiple iDR-8 system This diagram Linking iDR-8 Units SlaveUnit a Adding the iDR-switch Expander Checking for iDR-switch expanders You canConnecting to the iDR-8 The iDR-8communicates Connectors and grounding Pluggable Phoenix Using the switch closure inputs The input isUsing the logic outputs Each output is opto MIDI, SysNet and PL-Anet Ports SysNetSelecting the Communications Options Click on IDR-8 unit settings These are Configuration file settings These areIDR-8 Memory System Starting with the Patches Decide your system starting point AssignOnly store the parameters you need For your Technical Specification DR-8Application DR-8Headphones IDR-8 Installer Front PanelIDR-switch Front Panel DescriptionPower Supply IDR-switch InputsIDR-switch Logic Outputs Network PortClock Soft SwitchesSoftware NamingLevel Control DelaySignal Generator Fader GroupsFactory default unit settings Factory default configuration settingsFactory default patch parameters Template for Allen & Heath iDR-8 Front Panel Key Label
Top Page Image Contents