Compex Systems AP4530 manual Limited One Year Warranty, Conditions Of Warranty

Page 2

Limited One Year Warranty

This product is warranted to be free from defects in materials or workmanship for period of one year from the date of purchase by the original owner.

To ensure a high level of performance and reliability for which this equipment has been designed and manufactured, read this User Guide before operating.

In the event of a failure, notify and return the defective unit to ALLEN & HEATH Limited or its authorised agent as soon as possible for repair under warranty subject to the following conditions

Conditions Of Warranty

1.The equipment has been installed and operated in accordance with the instructions in this User Guide.

2.The equipment has not been subject to misuse either intended or accidental, neglect, or alteration other than as described in the User Guide or Service Manual, or approved by ALLEN & HEATH.

3.Any necessary adjustment, alteration or repair has been carried out by ALLEN & HEATH or its authorised agent.

4.The defective unit is to be returned carriage prepaid to ALLEN & HEATH or its authorised agent with proof of purchase.

5.Units returned should be packed to avoid transit damage.

In certain territories the terms may vary. Check with your ALLEN & HEATH agent for any additional warranty which may apply.

This product complies with the European Electromagnetic

Compatibility directives 89/336/EEC & 92/31/EEC and the

European Low Voltage Directives 73/23/EEC & 93/68/EEC.

This product has been tested to EN55103 Parts 1 & 2 1996 for use in Environments E1, E2, E3, and E4 to demonstrate compliance with the protection requirements in the European EMC directive 89/336/EEC. During some tests the specified performance figures of the product were affected. This is considered permissible and the product has been passed as acceptable for its intended use.

Allen & Heath has a strict policy of ensuring all products are tested to the latest safety and EMC standards. Customers requiring more information about EMC and safety issues can contact Allen & Heath.

NOTE: Any changes or modifications to the equipment not approved by Allen

&Heath could void the compliance of the equipment and therefore the users authority to operate it.

iDR-8 User Guide AP4530 Issue 1

Copyright © 2002 Allen & Heath Limited. All rights reserved

Whilst we believe the information in this guide to be reliable we do not assume responsibility for inaccuracies. We also reserve the right to make changes in the interest of further product development.

Allen & Heath Limited

Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK

http://www.allen-heath.com

2

IDR-8User Guide

Image 2
Contents IDR-8 Limited One Year Warranty Conditions Of WarrantyThis appliance must be earthed Important Safety Instructions Read FirstImportant Mains Plug Wiring Instructions IDR-8User GuideIntroduction Contents Welcome to the iDR-8 DR-8Daisy chain iDR-8 units Any number may be Main FeaturesIDR-8 main processing unit 2U, 8 mic/line Stereo audio monitor with front panelExpander status LEDs These display Front Panel OverviewFront panel RS232 port This is used for Rear Panel Overview Monitor in L Monitor OUT LSystem Processing Overview IDR-8User Guide Page Getting Started Check the Contents IDR System Manager Software BundleInstalling the iDR-8 IDR-8 Main UnitEarthing Turning the iDR-8 On and Off Parameters restored on power-up The iDR-8Starting Offline with iDR System Manager Software Checking the iDR-8 Operating Code Version Updating the iDR-8 Operating CodeIDR-8 Setup Menus PPP SetupRebooting the iDR-8 Accessing the iDR-8 Setup MenusChecking the Current Settings and Status Changing the Unit NameGetting Started Checking the Hardware DR-8RS232 COM Port Communicating with the iDR-8Network Port Communicating Using a TCP/IP Connection How to get the MAC address Connecting the iDR-8 Direct to the PCConnecting the iDR-8 to a Network Connect the PC to the iDR-8 Plug the PC Ethernet portChanging the iDR-8 PPP settings Go to menu *6 PPP Communicating Using a Dial Up ConnectionSetting up a Dial-up Connection Setting up the PC dial-up connection You needStarting the iDR System Manager Connecting the iDR-8 to a ModemDial up the iDR-8 using the remote PC Open up Connect the iDR-8 to the modemWorking with the iDR System Manager Setting the Time and Day ClockArchiving and Loading Configurations Start the iDR System Manager from the Start / ProgramsXLR Analogue Inputs and Outputs Input Source window From within the InputMonitor TRS Input and Output The monitor is Monitor Headphones Output This followsMonitor Inputs and Outputs Using the Monitor as Additional Channels Daisy chaining iDR-8 monitors The activeTurning the expander on or off Turn the unit on Adding the iDR-in and iDR-out Audio ExpandersCheck the connections The iDR-inAUDIO OUT Checking for expanders You can use the frontExpanded multiple iDR-8 system This diagram Linking iDR-8 Units SlaveUnit a Connecting to the iDR-8 The iDR-8communicates Adding the iDR-switch ExpanderChecking for iDR-switch expanders You can Connectors and grounding Pluggable Phoenix Using the switch closure inputs The input isUsing the logic outputs Each output is opto Selecting the Communications Options Click on MIDI, SysNet and PL-Anet PortsSysNet IDR-8 Memory System IDR-8 unit settings These areConfiguration file settings These are Only store the parameters you need For your Starting with the PatchesDecide your system starting point Assign Technical Specification DR-8Application DR-8Headphones IDR-8 Installer Front PanelIDR-switch Front Panel DescriptionPower Supply IDR-switch InputsIDR-switch Logic Outputs Network PortClock Soft SwitchesSoftware NamingLevel Control DelaySignal Generator Fader GroupsFactory default patch parameters Factory default unit settingsFactory default configuration settings Template for Allen & Heath iDR-8 Front Panel Key Label