Euphonix EuCon manual User Guide, Communications and Safety Regulation Information

Page 2

USER GUIDE

ii

professional control surface

In the interest of continued product development, Euphonix reserves the right to make improvements to this manual and the product it describes at any time, without notice or obligation.

Artist Series, MC Mix, MC Control, MC Pro, System 5-MC, and EuCon are trademarks of Euphonix, Inc.

©2008 Euphonix, Inc. All rights reserved worldwide. No part of this publication may be reproduced, trans- mitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without written permission from Euphonix, Inc.

Communications and Safety Regulation Information

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener- ates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:

Reorient or locate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Modifications made to the product, unless expressly approved by Euphonix, Inc., could void the user's authority to operate the equipment.

Always use a shielded Ethernet cable to connect to your MC Mix, such as the one supplied with the unit.

DECLARATION OF CONFORMITY

We Euphonix, Inc.,

220 Portage Ave

Palo Alto, CA, 94306 USA

(650) 846-1173

declare under our sole responsibility that the product

MC Mix

complies(y) with Part 15 of FCC Rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undes- ired operation.

Artist Series

Image 2
Contents User Guide Communications and Safety Regulation Information User GuideJapan CanadaEuropean Union Australia Important Safety Instructions User Guide Page Table of Contents Viii List of Figures Page Introduction to the Artist Series EuControl SoftwareConventions Used in this User Guide Setting Up the MC Mix Elevating the MC MixPhysically Linking Artist Series Devices 2Removing side panels left removing riser brackets3Removing screws from the bottom panel Installation 6Menu bar with EuControl icon8Ethernet cable and rear panel jack Controlling a Second Workstation Connecting a Footswitch 10 Footswitch input on rear panelPage Common Tasks Fader StripPress the Home key -2to restore tracks 1-8 to strips Inserts Fader strip, Inserts and Chan keysPress the page keys to access more parameters Figure Chapter Power Switch Shift KeyOled Dimming Fader StripsDisplay Screens Solo Fader3 on Transport Controls REW6 SEL 30 4.3.7 AssignFader Navigation Controls Bank and NudgeNavigating Among Multiple MC Mixes Not all applications support these keysKnobs Basic Knob UseKnob Modes Normal ModeChannel Mode Chan KeyKnob Set Selector Keys 11Knob Selector keysMIX Knob Set Navigation Keys Configuration Pages CFGDual-Function Knobs User Guide Knob Sets and Multiple MC Mixes BackUser Guide Surfaces EuControlAdd B All SurfacesMy Surfaces Show Info WorkstationsRemove Attach/Detach All WorkstationsMy Workstations General General PreferencesSolo Mode Preferences 46 5.4 Preferences EuControlMC Control Display FootswitchMC Mix display screen dim time OperationAssign Assign tabClear All LayoutsDisplay application’s track numbers RecallClear Appendix a Setting the IP Address Professional control surface