Fostex VR800 Trimming the sound while previewing, Press the Stop button or the EXIT/NO key

Page 60

VR800 Owner’s Manual (Preview Function)

2.To adjust the monitor sound of the selected track so that it can be monitored on the mixer.

Note: If data stored in each memory key is in the initial state, all memory keys will be in ABS time 00H 00M 00S.

In other words, the program head value is in the memory. Should fade out preview be executed in this condition, the [Void Data !] message and memory data [00H 00M 00S] will alternately flash in the display as a warning. However, for fade in preview, this will function as the memory data [00H 00M 00S] point.

3. Press the STOP button or the EXIT/NO key.

Trimming the sound while previewing

You can trim the position of the locate point (edit point) using the JOG dial while you preview the sound.

At this time, you can also adjust the size of the trimming steps (the amount of offset controlled by the JOG dial). Trimming allows you to fine-tune the position of the locate point stored in the memory keys while previewing the sound.

Use this function to change the Auto Punch In/Out points, the start point of Copy & Paste and Move & Paste, and the start and end points of the Erase function.

<Notes>

•You can audition the result of trimming during the next preview. That is, if you trim the position while previewing the sound for the first time, you can check the result when you preview the sound next time.

•If the locate point is shifted outside the range of the preview playback as a result of trimming, [Void Data!] and the locate point indication appear alternately. In this case, you cannot use the Preview function. Trim the position again so that it will be within the playback range.

•When Auto Punch mode is turned on and you trim the Auto Punch In or Auto Punch Out point while previewing the sound with [Void Data!] indicated on the display, Auto Punch mode will be cancelled.

1.Start previewing the sound by following the steps described on the previous page.

2.Use the JOG dial to trim the position.

When previewing starts, the unit of JOG trimming flashes on the screen. For example, value of SF (sub-frame) flashes if ABS Time Base or MTC Time Base is selected. CLK (clock) flashes if BAR/BEAT/CLK is selected.

The flashing value also indicates the position you can trim.

Example: Time Base is ABS (value of SF flashes.)

DIGITAL

44.1kHz

 

 

ABS

 

 

 

Flash

LOC

H

M

S

F

SF

 

 

 

SYNC OUT

 

DRIVE

 

 

 

CLK

 

SCSI

 

 

 

AUTO

 

A.PUNCH

Example: Time Base is BAR/BEAT/CLK (CLK flashes.)

DIGITAL

44.1kHz

 

BAR

CLK

Flash

LOC

 

 

SYNC OUT

DRIVE

 

CLK

SCSI

 

AUTO

A.PUNCH

 

3. To change the unit of trimming, press the HOLD/> key, the REWIND button, or the F FWD button.

These buttons will change the trimming unit as follows:

 

 

 

 

Time Base

 

 

ABS or MTC

 

BAR/BEAT/CLK

HOLD/> key

H

M

S

F

CLK

BAR

SF

or

 

 

 

 

 

 

F FWD button

 

 

 

 

 

 

REWIND button SF

H

M

S

F

CLK

BAR

4.Trim the position at the selected unit (digit).

5.Press the STOP button or the EXIT/NO key.

The trimmed locate point (edit point) data will be stored in the corresponding memory key.

60

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Model Safety Instructions Table of Contents 106 Introduction Precautions Names and Functions Top panelAccess LED Access Record track select keys Record Track 1Contrast adjustment knob Setup key SetupClipboard In key Clipboard IN/ Preview Execute/Yes key EXECUTE/YESAuto Return/Auto Play mode on/off key Edit key EditJOG dial JOG/ Shuttle Scrub key ScrubVari Pitch key Vari PITCH/ P.EDIT Shift key ShiftFast forward button F FWD Rewind button RewindRecord button RECORD/ Auto Punch Store key StoreHold/ key Hold Auto Return End key Auto RTN END/ Preview Auto Return Start keyAuto Punch In key Auto Punch IN/ Preview Auto Punch Out keyData output jack Data OUT Connector Optical Data input jack Data in Connector OpticalMidi OUT jack Midi OUT Connector DIN 5-pin Scsi connector Scsi Connector D-SUB 25-pinSide Panel Display Section Time base is ABS DigitalTime base is BAR/BEAT/CLK Time base is MTCAcc Error message Load Err messageUnformat ! message Action to takeBefore Starting Time BaseRecording method and Remain indicator Remain indicatorRecording method Managing songs by Program Change function You can name a programReal tracks and Additional tracks You can swap data between twenty-four mono tracksAdditional tracks in units of eight tracks When you set a track to recording mode When you set a track to recording stand-by modeInput monitoring and playback monitoring Input monitoringAudio file and event About an audio fileHints Recording mode Formatting a DiskFormatting a current drive disk Scsi disk Formatting a new diskRe-formatting a formatted disk Insert a formatted disk into the Scsi drivePress the EXECUTE/YES key Press the EXECUTE/YES key againFormatting a backup disk Scsi disk Formatting an unformatted disk for backupInsert a new disk into the backup drive Formatting a current drive disk 3.5-inch E-IDE hard diskFormatting a backup disk fixed disk Re-formatting a formatted disk for backupInsert a formatted disk into the backup drive Turn on the power to the VR800 and a connected Scsi drive Handling ProgramsCreating a new Program While holding down the HOLD/ key, press the Store keyUsing a Program Change function To enter a titlePress the Setup key while the VR800 is stopped Deleting a ProgramEditing a Program title JOG dial to enter characters or numbersAfter you enter the title, press the EXECUTE/YES key What is Punch In/Out recording? Punch In/Out RecordingAuto Punch In/Out Storing the edit pointsMusic instrument Guitar Rehearsing Auto Punch In/Out recording Press the Record button while holding down the Shift keySet the track for Auto Punch In/Out to Ready Recording levelWhen you finish recording, press the Stop button Auto Punch In/Out TakeUndo/Redo Auto Punch In/Out recording Press the Record button while holding down the Play buttonPress the foot switch while holding down the Stop button Manual Punch In/OutRehearsing Manual Punch In/Out recording Play the guitar accompanying the playback of tracksCancelling Rehearsal mode Manual Punch In/Out takeUndo/Redo Manual Punch In/Out recording Recording to a Metronome Sound Creating a Tempo MapTurning the Metronome function on Music InstrumentAdjusting monitor/record level of the musical instrument Checking the metronome soundStarting recording Quitting recordingConnecting an external digital device Assigning tracks and setting the digital-in clockDigital Recording Digital recording from an external digital deviceDigital recording to an external device Selecting a recording trackStarting and quitting recording Setting a digital output track Selecting a playback programStoring a Locate Point Edit Point Memory keyStoring and editing the locate points to the memory keys Storing in real-timePress the Store key Press the desired memory keyEditing and storing locate data Editing and storing dataPress the HOLD/ key while the VR800 is stopped Press the memory key that you pressed in againStoring and editing Locate key Select the Locate number desired using the JOG dial Next press the Locate keyPress the Store key. the Store key lamp lights up Edit and re-store data that is already stored Locate Function Direct LocateAuto Play Auto ReturnAuto Repeat Start playback a little before the Auto RTN Start pointCue & Review function using the Rewind and F FWD buttons Cue & Review function using the Shuttle featureCue & Review Function Digital scrubbing using the Scrub function Press the Scrub key while the VR800 is stoppedTurn the JOG dial to perform digital scrubbing Press the Stop button to stop the digital scrubbingPreview Function Executing the Preview functionPreviewing the rise of the sound fade Previewing the fall of the sound fade outTrimming the sound while previewing Press the Stop button or the EXIT/NO keyEditing Tracks Copy & Paste and Move & PasteCopy & Paste Move & PasteExecuting Copy or Move Checking the clipboard dataPaste start point Key for which you wish to check the edit pointExecuting Paste Undo/Redo PasteSelect a destination track to paste data Turn the JOG dial to enter the number of repeats Repeat=Erase Erasing a specified part of the data between ABS 0Erasing data from a specified point to REC END Executing Erase Undo/Redo EraseStoring the erase start and end points Track Exchange Swapping mono track data between Real tracks, AddiExecuting Track Exchange Connecting external equipment Refer to connecting schematic Midi sync functionConnect the VR800 Midi OUT to Midi in of the Midi sequencer Setup of VR800 Confirming the Midi clock syncMTC sync/MIDI machine control system Execution of recordingConnecting to external equipment Setup of external equipmentOffset mode For ABS Confirming MTC sync/MMCExternal Midi equipment sync system by the slave mode Connection to external equipmentPrecautions at MTC related setups Confirming chase lockUsing a Scsi drive as the current drive Saving and Loading Song DataOutline of the save/load operation Fostex D-5, Pioneer D-05 Save DAT or adat Saving/loading data using another Scsi drive Title of data to be saved to a backup Scsi diskInsert an unformatted disk into the backup drive Press the EXIT/NO key to exit Setup modeSave PGM ? menu Select a flashing SCSi id-6 and press EXECUTE/YES key Load PGM ? menuSaving/loading via a DAT or adat Saving song data via a DAT or adat DAT or adat connection and preparationUse the JOG dial to select a Program to save Use the JOG dial to select the desired tracksStart recording on the DAT or adat Loading song data via a DAT or adat ProgressesStart playing the DAT or adat Use the JOG dial to select a Program into which to load dataSaving and loading song data via a Scsi drive If you wish to delete the existing data If you do not wish to delete the existing dataChanging the Initial Settings Setup Mode Selecting Setup mode Following diagram shows the position of each menuSetting a time signature Sign. Set ? menu Storing a time signatureSelect a Program for which to set a time signature Clearing all time signature and tempo settings Modifying or deleting stored time signaturesChanging the BAR at ABS 0 of the time base Setting a tempo Tempo Set ? menu Checking the stored tempo settingSelect a Program to check the tempo setting for Storing a tempo valueSetting the Metronome function Click ? menu Setting the Metronome functionRepeat steps 3-5 to store necessary tempo data Setting a preroll value Preroll ? menu Setting a preroll timeTurn the JOG dial to select on or oFF Turn the JOG dial to enter a desired preroll time valueSetting Midi sync output signal Sync Out ? menu Setting Midi sync signalTurn the JOG dial to select the desired Midi sync signal Setting an MTC frame rate Frame Rate ? menu Setting an MTC offset value Mtc Offset ? menuSetting an MTC frame rate Turn the JOG dial to enter the desired frame rateSetting Offset mode Ofset Mode ? menu Setting an MTC offsetSetting the Slave mode Slave Mode ? menu Setting MTC Offset modeTurning Slave mode on and off Use the JOG dial to select the desired Offset modeSetting the Slave type Slave Type ? menu Setting the Slave typeUse the JOG dial to turn Slave mode on and off Use the JOG dial to select the desired Slave typeSetting the Record Protect function Rec Protect ? menu Recording enabled/disabledUse the JOG dial to enable or disable recording 100Setting digital input tracks Digi. In ? menu Setting digital input tracks101 Setting digital output tracks Digi. Out ? menu Setting a clock of digitalSetting digital output tracks 102Setting BAR/BEAT resolution mode Resolu ? menu Setting BAR/BEAT resolution mode103 Setting the Midi device number Device ID ? menu Setting the Midi device IDUse the JOG dial to turn the mode on or off 104Checking the number of track events NOs Event ? menu Checking the number of track events105 Midi Implementation Chart 106Transmitted Recognized Remarks Command List Movement Recorder MMC Response/Information Field List Command107 Fostex Midi System Exclusive Message Format for VR800 108Status Request 109Example 2 Locate memory is recalled using the read command 110111 Data Type112 Signature map113 114 Status Request Command 115116 117 Maintenance 118Declaration of EC Directive 119Index Remain Fostex Corporation
Related manuals
Manual 24 pages 22.9 Kb
Top Page Image Contents