Alesis DM5 manual To set the Decay value, To set the Noise value

Page 22

Connections: Chapter 3

Decay

Note: In this scenario we will use only the snare pad. Depending on the type of pads being used and your mounting configuration, you may be experiencing some “double triggering”. If shortly after the initial strike to the snare pad it re-triggers or sounds a second time, the pad is “double triggering”. This can be controlled by altering the Decay parameter value.

To set the DECAY value:

➀Press [EXT TRIG] repeatedly until PAGE 2 is selected.

In the bottom left corner of the display, PAGE 2 will have a square around it. There are three parameters in this page: Xtalk, Dec and Nois. The Trigger Number will be selected (i.e. a circle around the currently selected Trigger Number will be flashing).

➁Turn the [VALUE] knob to select the desired trigger (snare).

➂Press [] twice to select the Dec parameter. The value beneath it will be flashing.

➃Turn the [VALUE] knob to gradually increase the value until the snare stops double triggering on hard hits.

A properly adjusted Decay parameter will end double triggering, and still allow you to play fast, repetitive hits on the snare pad.

Noise

Note: In this scenario we will be using the tom 1 and the tom 2 pads in a live performance situation. The two tom pads are mounted together on a single floor stand, and the Crosstalk and other parameters have already been correctly adjusted. When you play the pads while no other instruments are being sounded, all of the hits are triggering and tracking properly.

Now as the band begins and the stage volume is very loud, the stage starts trembling which causes the drum hardware to vibrate. At times the tom 1 and the tom 2 pad are triggering when not being played. This is because the DM5 is interpreting the signals from the stand vibrations as hits. By adjusting the Noise parameter the DM5 can determine which signals are vibrations caused by the surrounding noise level, and which signals are actual hits.

To set the NOISE value:

➀Press [EXT TRIG] repeatedly until PAGE 2 is selected.

In the bottom left corner of the display, PAGE 2 will have a square around it. There are three parameters in this page: Xtalk, Dec and Nois. The Trigger Number will be selected (i.e. a circle around the currently selected Trigger Number will be flashing).

➁Turn the [VALUE] knob to select the desired trigger (tom 1).

➂Press [] three times to select the Nois parameter. The value beneath it will be flashing.

➃Turn the [VALUE] knob to increase the value to a level that will stop the pad from false triggering when the strong vibrations occur.

If the triggering is frequent and strong, try starting with an increase of 20 or more. If the triggering is not as often and is softer in volume, first try adding 10 to the value, then gradually add more if necessary.

DM5 Reference Manual

21

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Alesis DM5 HOW to USE this Manual IntroductionDM5 Reference Manual Contents Midi Functions Appendix a TROUBLE-SHOOTINGMidi Implementation Chart External TriggeringUnpacking and Inspection Setting UPAC Power Hookup ChapterAbout Audio Cables Basic Audio HookupMidi Hookup To turn on the Midi Thru parameterExternal Triggers Hookup Your First Session With the DM5 Powering UPPlaying the Demo Sequence Auditioning Internal Programs WHAT’S a Drum SET?Playing the DM5 Selecting the Midi ChannelChoosing Voices in a Drum SET Naming a Drum SET Storing AN Edited Drum SETRecalling the Factory Drum Sets To turn on Midi Thru Mode Midi OUT/THRU ModeConnections To set the Midi Channel Example 1 Using a Midi KeyboardTo set the Root Note Example 2 Using a Midi Sequencer Local Mode To turn the Local Control offExample 3 Using TWO or More DM5 Modules To turn the Midi Overflow Mode on External Triggers To setup the external triggers Crosstalk To Set the Crosstalk valueTo set the Decay value To set the Noise valueFootswitch Hookup To set the Footswitch ModeVoice OverviewBasic and Definitions Random VoicesDM5 Polyphony Midi Note RangeAbout the User Interface Reading the DisplayButtons Function ButtonsMULTI-PAGE Functions Store Button Drum Note SelectionEditing Parameter Values Preview ButtonFunction Buttons TuneMIX OutputOutput Options EXT Trig Drum SETGroup Midi Copying a NOTE’S Parameters to AnotherMidi Functions Drum SET Root NoteMidi Channel Program Change Enable Local ControlControllers Enable Saving Data VIA Midi Program Change TableTo edit the Program Change table Receiving Data from Another Midi Device To back upExternal Triggering OverviewAbout Trigger Parameters Page Example Trigger Selection Gain Trigger Note AssignmentVelocity Curve Method One Method TwoCrosstalk Decay Footswitch ModeNoise Understanding HI HAT Pedal Mode Output Sensitivity Trigger PlacementTips on Triggering from Acoustic Drums MountingFor head mounting If you play with a fairly tight batter head, try thisIf you play with a looser head, try this For shell mountingMuffling Mounting Hardware and ConfigurationLarge Toms External Triggering DM5 Reference Manual MAINTENANCE/SERVICE TROUBLE-SHOOTINGTROUBLE-SHOOTING Index RE-INITIALIZINGRefer ALL Servicing to Alesis MaintenanceObtaining Repair Service Customers in the USA
Related manuals
Manual 1 pages 58.02 Kb
Top Page Image Contents