BASIC OPERATIONS (CONT.)
Changing the Sample Parameters:
Changing the sample parameters allows you to change the sample's volume and pitch. The param- eters values for both the pitch and volume settings range from 00:00 to 20:00, 00:00 being the lowest value. A higher value will increase the pitch percentage or volume. It's important to understand that the pitch value is basically a speed adjustment and has nothing to do with tonal quality. The values can be either a momentary change or set adjustment. The sample values are changed in three easy steps, while in sample playback mode:
Changing the Sample Parameters - Speed
While a sample is playing push the PARAMETERS TIME BUTTON (1). One tap will display SP +0 00 in the LCD DISPLAY (19). SP will signify the pitch percentage (speed) of the sample. +0 00 is your default setting - Normal playback. Any adjustments will be based on this default setting. Turning the knob in a clockwise direction will increase your pitch. Turning the wheel in a
| OFF |
|
|
|
|
| Figure 28 |
POWER | ON |
|
|
|
|
| |
|
|
|
|
|
|
| |
1 | 2 3 4 5 6 | 7 8 9 0 | PROGRAM | NONSTOP | AUTO |
| |
PARAMETER TIME |
| CUE | ELAPSED | TOTAL REMAIN | CUE BPM | KEY | |
| BEAT SYNC. | LOCK | |||||
SINGLE |
|
|
|
|
| EJECT | |
| LOOP |
|
|
|
|
| BPM |
RELOOP | T | M | S | F |
| PITCH | |
PARAMETER RATIO
| OFF |
|
|
|
|
|
|
POWER | ON |
|
|
|
|
|
|
1 | 2 3 4 5 6 | 7 8 9 0 | PROGRAM | NONSTOP | AUTO |
| |
PARAMETER TIME |
| CUE | ELAPSED | TOTAL REMAIN | CUE BPM | KEY | |
| BEAT SYNC. | LOCK | |||||
SINGLE |
|
|
|
|
|
| |
| LOOP |
|
|
|
|
| BPM |
RELOOP | T | M | S | F |
| PITCH | |
PARAMETER RATIO |
|
|
|
| |
| SCRATCH | FILTER | HOLD | ECHO | TRANS |
|
|
|
|
|
|
|
|
|
|
|
|
| SKID | PHASE |
| FLANGER | PAN |
BOP
FX
MIX
ENTER
EJECT
FX SELECT | SGL/CTN |
TIME REV.PLAY
TEMPO ON/OFF
LOCK 4%/8%/16%
SAMPLE PITCH
SCRATCH | FILTER | HOLD | ECHO | TRANS |
|
|
|
|
|
|
|
|
|
|
SKID | PHASE |
| FLANGER | PAN |
BOP
FX
MIX
ENTER
FX SELECT | SGL/CTN |
TIME REV.PLAY
TEMPO ON/OFF
LOCK 4%/8%/16%
SAMPLE PITCH
Changing the Sample Parameters - Volume
While a sample is playing push the PARAMETERS RATIO BUTTON (3). One tap will display SV 10 00 in the LCD DISPLAY (19). SV will signify the volume of the sample. 10 00 is your default setting - Normal playback. Any adjustments will be based on this default setting. Turning the knob in a clockwise direction will increase the volume. Turning the wheel in a counter- clockwise direction will decrease the parameters value.
Figure 29
|
| OFF |
|
|
|
|
|
| |
POWER |
| ON |
|
|
|
|
|
| |
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 |
PARAMETER TIME |
|
|
|
|
| CUE |
| ||
SINGLE |
|
|
|
|
|
| |||
| LOOP |
|
|
|
|
|
|
| |
RELOOP |
|
|
|
|
| T | |||
PROGRAM | NONSTOP | AUTO |
CUE BPM | ||
ELAPSED | TOTAL REMAIN | BEAT SYNC. |
M 
S 
F
KEY
LOCK
EJECT
BPM
PITCH
PARAMETER RATIO
Changing the Sample Parameters - Hold Function
Hold Function - This mode will allow you to save and lock your parameter adjustments, if the hold function is not activated all your parameter adjust- ments will be momentary. If you select the HOLD BUTTON (2) all param- eters will remain until changed again or power is shut off, unless they are stored in to the unit's memory.
SCRATCH | FILTER | HOLD | ECHO | TRANS |
|
|
|
|
|
|
|
|
|
|
SKID | PHASE |
| FLANGER | PAN |
BOP
FX
MIX
ENTER
FX SELECT | SGL/CTN |
TIME REV.PLAY
TEMPO ON/OFF
LOCK 4%/8%/16%
SAMPLE PITCH
Figure 30
©American Audio® - www.americandj.com -