GENERAL FUNCTIONS AND CONTROLS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
|
|
|
|
|
|
|
|
| OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| POWER | ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| AUTO |
|
|
| |||||||
1 | 2 3 4 5 6 | 7 8 9 0 | PROGRAM |
| NONSTOP |
| KEY | ||||||||||||||
| PARAMETER TIME |
| CUE | ELAPSED | TOTAL REMAIN | CUE BPM | |||||||||||||||
|
| BEAT SYNC. | LOCK | ||||||||||||||||||
|
|
|
|
|
|
|
| SINGLE |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| LOOP |
|
|
|
|
|
|
|
|
| BPM | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| RELOOP | T | M |
| S | F |
|
| PITCH | |||||
| PARAMETER RATIO |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
| SCRATCH | FILTER | HOLD |
| ECHO | TRANS |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SKID | PHASE |
|
|
| FLANGER | PAN |
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 18 | Figure 3 |
|
|
| |
|
| 19 |
|
EJECT | 20 |
| |
|
|
| |
|
| 21 |
|
FX SELECT | SGL/CTN | 22 |
|
TIME | REV.PLAY | 23 |
|
|
| ||
TEMPO | ON/OFF | 24 |
|
25 |
| ||
LOCK | 4%/8%/16% |
| |
|
| 26 |
|
27
| BOP | 28 |
FX |
| SAMPLE PITCH |
| 29 | |
MIX |
| |
| ENTER |
|
30
31
32
33
34
A. TOP UNIT CONTROLS (FIGURE 3)
1.PARAMETER TIME - This knob is used to adjust the parameter time value.
2.HOLD BUTTON - This button allows you to set and lock any new parameters you set to the effects. This button will glow bright blue when the hold function is activated. If the hold function is not selected any changes to the effect param- eters will be momentary.
3.PARAMETER RATIO - This knob is used to adjust the parameter ratio value.
4.FILTER/PHASE BUTTON - This button is used to activate and deactivate either the Filter or Phase effect. See
5.SEARCH WHEEL - This wheel has four for- ward and four reverse speed positions allowing you to quickly scan through tracks. The more you turn the wheel in either direction, the faster your search.
6.SCRATCH/SKID BUTTON - This button is used to activate and deactivate either the Scratch or Skid effect. See
7.P.S.P. (Pre Set Parameters) BUTTON - This button is used to activate the effect preset. Each effect comes with four preset, this button access the presets.
8.FLASH BUTTONS
(3) samples. Each Flash Button can store either a sample or a cue point.
9.MEMORY BUTTON - This button allows you to program up to 3 cue points or three samples in to the three FLASH BUTTONS (8). The samples or cue point can then be recalled at any time even when the disk has been removed and replaced at a later time.
©American Audio® - www.americandj.com -