Using Flexible Vent Components

CAULKING

4"FLEX

PIPE

7" FLEX PIPE 2" OVERLAP

HI-TEMP

TERMINAL SEALANT EXTENSION

PLATE

#10x2"

SCREWS

DO NOT CLAMP THE

FLEXIBLE

ALUMINIUM LINER.

FIGURE 19 a,b&c

Use only approved aluminum ﬂexible liner kits marked:

“Wolf Steel Approved Venting” as identiﬁed by the stamp only on the 7” outer liner.

For safe and proper operation of the ﬁreplace, follow the venting instructions exactly.

All inner exhaust and outer intake vent pipe joists may be sealed using either Red RTV high temp silicone sealant or Black high temp Mill Pac with the exception of the ﬁreplace exhaust ﬂue collar which must be sealed using Mill Pac (not supplied).

Spacers are attached to the inner ﬂex liner at predetermined

intervals to maintain a 1-1/4” air gap to the outer ﬂex liner.

These spacers must not be removed.

HORIZONTAL AIR TERMINAL INSTALLATION

Note: Direct vent terminals shall not be recessed into a wall or siding.

1.Cut or frame a hole in an exterior wall with a minimum round or square opening of 111/2” W x 111/2” H if within 24” of the ﬁ replace collars. If beyond 24” then a 91/2” W x 91/2” H opening is acceptable. Secure the ﬁ restop spacer over the opening to the interior wall.

Secure the terminal to the terminal extension plate if required (see ﬁgure 18). The cover plate of the GD-222R terminal is 13”x13” and will cover the 11 1/2” x 11 1/2” opening but if the opening is made any larger - the terminal extension plate is required.

2.Stretch the 4” diameter aluminum ﬂ exible liner to the required length taking into account the additional length needed for the ﬁ nished wall surface. Slip the liner a minimum of 2” over the inner sleeve of the air terminal and secure with 3 #8 screws. Apply a heavy bead of the high temperature sealant.

3.Using the 7” diameter ﬂ ex-

ible aluminum liner, slide over the

CAULKING

outer combustion air sleeve of the

air terminal and secure with 3 #8 screws. Seal as before. 4. Insert the liners through the

ﬁ restop maintaining the required clearance to combustibles. Se-FIGURE 17

cure to the exterior wall and make

weather tight by sealing with caulking (not supplied).

5.Apply a heavy bead of the high temperature sealant, (W573-0007 not provided), to the inside of the 4” liner ap- proximately 1” from the end. Slip the liner a minimum of 2” over the ﬁ replace vent collar and secure with 3 #8 screws.

6.Using the

7” diameter
ﬂ exible alumin-	4	7
ium liner, apply	4	7

	sealant, slide
	a minimum of	7
	2” over the ﬁ re-	7
	2” over the ﬁ re-
	place combus- FIGURE 18
	tion air collar
	and secure with 3 #8 screws.

VERTICAL AIR TERMINAL INSTALLATION

1.Move the ﬁ replace into position.

2.Fasten the roof support to the a roof using the screws provided. The roof support is optional. In this case the venting is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the optional roof support. (Fig.a)

3.Stretch the inner aluminum

ﬂ ex liner to the required length.

Slip the liner a minimum of 2” over the

inner sleeve of the air terminal connector and secure with 3 #8 screws. Seal using a heavy bead of the high temperature sealant. (Fig.b)

4.Repeat using the outer aluminum

ﬂex liner. (Fig.b)

5.Thread the air terminal connector / liner assembly down through the roof. The air terminal must be

located vertically and plumb. Attach the air terminal connector to the roof support, ensuring that the top of the air terminal is 16” above the highest point that it penetrates the roof. (Fig.c) If the attic space is tight, we recommend threading the Wolf Steel vent pipe collar or equivalent loosely onto the air terminal assembly as it is passed through the attic.

6. Remove nails from the shingles, above and to the sides of the chimney. Place the ﬂ ashing over the

air terminal connector leaving a min. 3/4” of the air terminal connector showing above the top of the ﬂ ashing. Slide the ﬂ ashing underneath the sides and upper edge of the shingles. Ensure that the air terminal connector is properly centred within the ﬂ ashing, giving a 3/4” margin all around. Fasten to the roof. Do not nail through the lower portion of the ﬂ ashing. Make weather-tight by sealing with caulking. Where possible, cover the

sides and top edges of c the ﬂ ashing with rooﬁ ng material. (Fig.c)

7.Aligning the seams of the terminal and air terminal connector, place the terminal over the air terminal connector making sure the liner goes into the hole in the terminal. Secure with the three screws provided. (Fig.c)

8.Apply a heavy bead of weatherproof caulking 2 inches above the ﬂ ashing. Note: Maintain a minimum 2” space between the air

inlet base and the storm collar. Install the storm collar around the air terminal connector and slide down to the caulking. Tighten to ensure that a weather-tight seal between the air terminal connector and the collar is achieved. (Fig.c)

W415-0583 / B / 05.23.07

GD82NT-T, GD82PT-T specifications

The Napoleon Fireplaces GD82PT-T and GD82NT-T are exquisite additions to any modern home, designed to combine style, efficiency, and advanced technology in one compact unit. These gas fireplaces offer remarkable features that cater to both aesthetic and functional needs, making them an ideal choice for homeowners seeking to enhance their living spaces.

At the heart of the GD82PT-T and GD82NT-T is Napoleon’s innovative burner technology. They utilize a unique PHAZER log set and glowing ember bed, creating a realistic flame effect that captures the essence of a traditional wood-burning fireplace while utilizing the convenience of gas. The stunning lifelike flames dance over the logs, providing ambiance and warmth that transforms any room into a cozy retreat.

One of the standout features of these models is their efficiency. Both the GD82PT-T and GD82NT-T are designed to provide substantial heating output while maintaining a high efficiency rating. The advanced heat distribution system ensures that warmth is evenly spread throughout the room, delivering comfort during colder months without excessive energy consumption.

In addition to their heating capabilities, these fireplaces come with Napoleon's patented Easy Clean glass, which helps minimize soot and residue build-up. This feature not only ensures a clearer view of the flames but also simplifies maintenance, allowing homeowners to enjoy their fireplaces without the hassle of frequent cleaning.

Another notable characteristic of the GD82PT-T and GD82NT-T is their customizable design options. Homeowners can choose from a variety of styles, including contemporary to traditional, with multiple finishes to ensure a perfect match with their existing décor. This versatility allows these fireplaces to seamlessly integrate into any living space while making a bold design statement.

Furthermore, the fireplaces come equipped with a remote control that allows users to adjust the flame height, thermostat settings, and other features with ease. This convenience enhances the overall user experience, providing the ultimate atmosphere at the touch of a button.

Safety is paramount, and Napoleon has incorporated several features to ensure peace of mind. These include an automatic shut-off system and a protective screen barrier, safeguarding against accidental contact with the hot glass.

Overall, the Napoleon Fireplaces GD82PT-T and GD82NT-T are exemplary choices for anyone seeking a perfect blend of beauty, efficiency, and technology. With their innovative design and advanced features, they stand out as premier options in the gas fireplace market, making them worthy investments for comfort and style in any home.