GAS Installation

6. Remove nails from the shingles, above and to the sides

of the chimney. Place the ﬂ ashing over the air terminal and

slide it underneath the sides and upper edge of the shingles.

Ensure that the air terminal is properly centred within the ﬂash-

ing, giving a 3/4” margin all around. Fasten to the roof. Do NOT

nail through the lower portion of the ﬂ ashing. Make weather-

tight by sealing with caulking. Where possible, cover the sides

and top edges of the ﬂ ashing with rooﬁ ng material.

7. Apply a heavy bead of waterproof caulking 2 inches

above the ﬂ ashing. Slide the storm collar around the air ter-

minal connector and down to the caulking. Tighten to ensure

that a weather-tight seal between the air terminal and the

collar is achieved.

Proceed once the vent installation is complete.

Note : All gas connections must be contained within

the ﬁreplace when complete.

1.The ﬁ replace is designed to accept a ½” gas supply line. The ﬁreplace is equipped with a ½” manual shut-off valve, and an 18” listed ﬂ exible gas connector.

FIGURE 25

8. Continue adding rigid venting sections, sealing and

securing as above. Attach a 4” collapsed telescopic pipe to

the last section of rigid piping. Secure with screws and seal.

Repeat using a 7” telescopic pipe.

9. Run a bead of high temperature sealant around the

outside of the 4” collar on the ﬁ replace. Pull the adjustable

pipe a minimum of 2” onto the collar. Secure with 3 screws.

Repeat with the 7” telescopic pipe.

10. In the attic, slide the vent pipe collar down to cover up

the open end of the shield and tighten. This will prevent any

materials, such as insulation, from ﬁ lling up the 1” air space

around the pipe.

MOBILE HOME INSTALLATION

8 7/8"

FIGURE 26

2.The access to the gas inlet is located on the right side of the outer shell.

3.The ﬂ ex connector and shut off must all be in the accessible portion of the

ﬁreplace.

4.When ﬂexing any gas line, support the gas valve so that the lines are not bent.

5.Check for gas leaks by brushing on a soap and water solution. Do not use open ﬂame.

This appliance is certiﬁ ed to be installed as an OEM (Origi- nal Equipment Manufacturer) installation in a manufactured home or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufac- tured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This ap- pliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is supplied with the mobile home appliance.

RESTRICTING VERTICAL VENTS

FIGURE 27	TOP OF THE
	FIREBOX
	RESTRICTOR PLATE

This Mobile/Manufactured Home Listed appliance comes factory equipped with a means to secure the unit.

The ﬁ replace is equipped with two 1/4” diameter holes located in the fron left and right corners of the base. For mobile home installations, the ﬁ replace must be fastened in place. Use #10 hex head screws, inserted through the holes in the base to secure.

Always turn off the pilot and the fuel supply at the source, prior to moving the mobile home.

After moving the mobile home and prior to lighting the ﬁreplace, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located manufactured (mobile) home, where not prohibited by local codes.

FLUE COLLAR

Vertical terminations may display a very active ﬂ ame. If this appearance is not desirable, the vent exit must be restricted using restrictor plate, W500-0205. This reduces the velocity of the exhaust gases, slowing down the ﬂ ame pattern and creating a more traditional appearance.

The plate has a series of holes to allow for adjustment. Remove the two screws on either side of the exhaust collar inside the ﬁ rebox. Install the plate in the desired set of holes, then replace the screws.

It is recommend to secure in the third set of holes which causes the greatest amount of restriction for vent length between 15 and 30 feet.

W415-0583 / B / 05.23.07

GD82NT-T, GD82PT-T specifications

The Napoleon Fireplaces GD82PT-T and GD82NT-T are exquisite additions to any modern home, designed to combine style, efficiency, and advanced technology in one compact unit. These gas fireplaces offer remarkable features that cater to both aesthetic and functional needs, making them an ideal choice for homeowners seeking to enhance their living spaces.

At the heart of the GD82PT-T and GD82NT-T is Napoleon’s innovative burner technology. They utilize a unique PHAZER log set and glowing ember bed, creating a realistic flame effect that captures the essence of a traditional wood-burning fireplace while utilizing the convenience of gas. The stunning lifelike flames dance over the logs, providing ambiance and warmth that transforms any room into a cozy retreat.

One of the standout features of these models is their efficiency. Both the GD82PT-T and GD82NT-T are designed to provide substantial heating output while maintaining a high efficiency rating. The advanced heat distribution system ensures that warmth is evenly spread throughout the room, delivering comfort during colder months without excessive energy consumption.

In addition to their heating capabilities, these fireplaces come with Napoleon's patented Easy Clean glass, which helps minimize soot and residue build-up. This feature not only ensures a clearer view of the flames but also simplifies maintenance, allowing homeowners to enjoy their fireplaces without the hassle of frequent cleaning.

Another notable characteristic of the GD82PT-T and GD82NT-T is their customizable design options. Homeowners can choose from a variety of styles, including contemporary to traditional, with multiple finishes to ensure a perfect match with their existing décor. This versatility allows these fireplaces to seamlessly integrate into any living space while making a bold design statement.

Furthermore, the fireplaces come equipped with a remote control that allows users to adjust the flame height, thermostat settings, and other features with ease. This convenience enhances the overall user experience, providing the ultimate atmosphere at the touch of a button.

Safety is paramount, and Napoleon has incorporated several features to ensure peace of mind. These include an automatic shut-off system and a protective screen barrier, safeguarding against accidental contact with the hot glass.

Overall, the Napoleon Fireplaces GD82PT-T and GD82NT-T are exemplary choices for anyone seeking a perfect blend of beauty, efficiency, and technology. With their innovative design and advanced features, they stand out as premier options in the gas fireplace market, making them worthy investments for comfort and style in any home.