Desa CDCFPR, CDCFTNA, CDCFTPA installation manual Installing Optional Blower Accessory GA3450TA

Page 13

INSTALLATION

Continued

11.Place metal trim on shoulder screws located on the side and top of the fireplace (see Assem- bling Perimeter Trim). Firmly snap trim over shoulder screws. Align fireplace in mantel assembly so the trim overlaps mantel evenly on all three sides.

12.Lower bottom louver door. Use 3" wood screws provided with mantel accessory to attach fire- place to base (see mantel instruction sheet).

Cabinet

Mantel

Hearth

Base

Figure 13 - Installing Cabinet Mantel onto Hearth Base

Cabinet

Mantel

Assembled

Trim

Hearth Base

Figure 14 - Installing Fireplace into Mantel Assembly

Assembling Perimeter Trim (Perimeter trim shipped with mantel)

1.Remove packaging from three remaining pieces of trim.

2.Locate two adjusting plates with set screws,

and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 15.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 15).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side perimeter trim (see Figure 15).

6.While firmly holding edges of perimeter trim together, tighten both set screws on the adjust- ing plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other corner.

8.Set perimeter trim assembly aside for later installation.

Set Screws

 

 

Adjusting

 

 

Plate

 

Top Brass

 

Slot

 

Trim

 

 

Shim

 

Mitered Edge

 

 

Side Brass

 

 

Trim

 

 

Figure 15 - Assembling Brass Trim

INSTALLING OPTIONAL BLOWER ACCESSORY GA3450TA

Removing Upper Louver To install the blower accessory, you must first remove the upper louver.

1.Lift screen off fireplace and remove log set if installed.

2.Remove 4 screws from upper louver (see Figure 16). Save these screws.

3.Pull upper louver straight out from the cabinet. Be careful not to scratch the paint. Set louver aside.

4.Open lower louver door by swinging door down (see Figure 16).

Top

Louver

Bottom Louver

Figure 16 - Removing Top Louver and

Opening Bottom Louver

111244-01F

www.desatech.com

13

Image 13
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Product Identification Product Features Optional Remote Control AccessoriesLocal Codes UnpackingSheet Metal Screws Hood Louver Firebox Top Hood AssemblyTools Required Phillips screwdriver Hex wrench ScissorsProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationBUILT-IN Fireplace Installation Installation ItemsFireplace Clearances Minimum Clearance to Combustible MaterialsActual Framing Height If you have not installed hood, follow instruc- tions onFront Width DepthMantel Clearances for Built-In Installation Optional Mantel InstallationMantel Shelf Installing Optional Blower Accessory GA3450TA Switch Plate Wire Remote Blower Harness Bracket Installing Blower AccessorySwitch Plate CordTest to make sure blower is working properly For Built-In InstallationLower louver Connecting to GAS Supply Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Equipment Open Shutoff Valve Closed Correct all leaks at onceGas Regulator or Equipment Gas Control Valve Gas MeterInstalling Receiver Optional Wireless HAND-HELD Remote Control AccessoriesInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wall MountedRemove jumper wire from control valve see , Feed wires through rectangular slotsTerminal W Terminal R R Rear Brick Liner Log Shoulder Screw Brick Liner Bracket ScreenLeft Brick Liner Log SetOperating Fireplace For Your Safety Read Before LightingLighting Instructions Ignitor Button Control KnobTo Turn OFF GAS To Appliance Manual Lighting ProcedureThermostat Control Operation Operating BlowerAUTO/OFF/ON Switch REMOTE-READY Models For Your Safety Read Before LightingPiezo Flame Control Ignitor Adjustment Knob Button Optional HAND-HELD Remote Operation If Using Optional Hand-Held RemotePilot Ignitor Burner Electrode Pilot Burner Ignitor ElectrodeAuto Thermostatic Mode Manual ModeON/OFF Series Model HRC100 Thermostat Series Model HRC200 SeriesInspecting Burners Optional GWMS2 Wall Mounted SwitchOptional GWMT1 Wall Mounted Thermostat Pilot Flame PatternBurner Flame Pattern Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole If pilot flame pattern is incorrect, as shown in ,LOG SET Wiring DiagramCabinet Remote-Ready Models OnlyObserved Problem Possible Cause Remedy TroubleshootingIgnitor cable pinched or wet Ignitor cable dryMote-Ready Models Only Burner orifice is cloggedModels Only Or replace burner orificeWalls or furniture Cleaners, etc. may turn into When heated, vapors fromMote-Ready Models Only Power is low Slight smoke or odor duringFireplace produces unwanted Gas odor even when controlErs, chemicals, new carpet Ment aboveDimensions H x W x D including hood SpecificationsThermostat Models Service Hints Replacement PartsTechnical Service Parts Under WarrantyIllustrated Parts Breakdown Parts List Cdcfpr Outer Casing Firebox Models Cdcfnr and Cdcfpr104281-02BR Firebox Hood Firebox Top Illustrated Parts Breakdown Hardware Pack Brass Flare Adapter FittingLighting Instruction Plate Not a field replaceable part FDCFTN/TP VDCFRN/RP CDCFNR/PR Lighting Instruction Plate THERMOSTAT-CONTROLLED Blower KIT GA3450TA AccessoriesEquipment Shutoff Valve GA5010 Brass Trim KIT GA6095WALL-MOUNT ON/OFF Switch GWMS2 WALL-MOUNT Thermostat Switch GWMT1Receiver and HAND-HELD Remote Control KIT HRC100 Series Information Video111244-01F 111244-01F 111244-01

CDCFTNA, CDCFPR, CDCFTPA specifications

Desa CDCFTPA, CDCFPR, and CDCFTNA represent a suite of advanced technologies and methodologies employed in the development and management of efficient distribution networks within the field of telecommunications and data services. These frameworks are designed to enhance connectivity, streamline processes, and ensure optimal performance in various environments.

One main feature of Desa CDCFTPA (Coaxial Digital Channel Fiber Transmission Protocol Architecture) is its ability to integrate coaxial cables with fiber optic technology, enabling high-speed data transmission over existing infrastructures. This hybrid approach not only reduces the need for extensive renovations but also capitalizes on the advantages of both technologies, offering broadband accessibility and improved bandwidth capabilities. By leveraging both mediums, operators can deliver enhanced services while maintaining cost-efficiency.

CDCFPR (Centralized Data Control Fiber Processing Resource) represents a centralized approach to managing data flow within telecommunications networks. Its core characteristic lies in its architecture, which supports dynamic allocation of resources in real-time. This enables network operators to efficiently allocate bandwidth based on demand, optimize routing paths, and reduce latency. Additionally, CDCFPR employs advanced algorithms for data compression and encryption, ensuring that users experience a seamless and secure connection.

CDCFTNA (Carrier Digital Channel Fiber Transmission Network Architecture) is focused on creating robust networks that can support a variety of distribution channels, including 5G and IoT devices. Its design emphasizes scalability and adaptability, allowing network providers to easily expand or modify their infrastructure to meet evolving market needs. Key technologies incorporated in CDCFTNA include Software-Defined Networking (SDN) and Network Function Virtualization (NFV), which enable operators to manage their resources more flexibly and efficiently.

Each of these frameworks boasts unique characteristics that contribute to the overall enhancement of telecommunications systems. They embody a commitment to innovation, sustainability, and user-centric design, aligning with current trends in digital services and communication technologies. By deploying such advanced systems, service providers can ensure they remain competitive in a fast-paced and continuously evolving market. In summary, Desa CDCFTPA, CDCFPR, and CDCFTNA collectively represent the future of telecommunications infrastructure, promising improved connectivity, efficiency, and adaptability for a diverse range of applications.