Desa CDCFPR, CDCFTNA Specifications, Thermostat Models, Dimensions H x W x D including hood

Page 34

SPECIFICATIONS

THERMOSTAT MODELS:

CDCFTPA, VDCFTP, FDCFTP

Rating: 17,000/26,000 Btu/Hr

Gas Type: Propane/LP Gas Only

Ignition: Piezo

Manifold Pressure: 8" W.C.

Inlet Gas Pressure (in. of water): Maximum - 14", Minimum* - 11"

Dimensions (H x W x D) (including hood and

screws): 25 7/8" x 26 13/16" x 15 5/16" * For purpose of input adjustment

CDCFTNA, VDCFTN, FDCFTN

Rating: 17,000/26,000 Btu/Hr

Gas Type: Natural Gas Only

Ignition: Piezo

Manifold Pressure: 3.5" W.C.

Inlet Gas Pressure (in. of water): Maximum - 10.5", Minimum* - 5"

Dimensions (H x W x D) (including hood and

screws): 25 7/8" x 26 13/16" x 15 5/16" * For purpose of input adjustment

REMOTE-READY MODELS:

VDCFRP, FDCFRP, CDCFPR

Rating: 17,000/26,000 Btu/Hr

Gas Type: Propane/LP Gas Only

Ignition: Piezo

Manifold Pressure: 8" W.C.

Inlet Gas Pressure (in. of water): Maximum - 14", Minimum* - 11"

Dimensions (H x W x D) (including hood and

screws): 25 7/8" x 26 13/16" x 15 5/16" * For purpose of input adjustment

VDCFRN, FDCFRN, CDCFNR

Rating: 17,000/26,000 Btu/Hr

Gas Type: Natural Gas Only

Ignition: Piezo

Manifold Pressure: 3.5" W.C.

Inlet Gas Pressure (in. of water): Maximum - 10.5", Minimum* - 5"

Dimensions (H x W x D) (including hood and

screws): 25 7/8" x 26 13/16" x 15 5/16" * For purpose of input adjustment

34

www.desatech.com

111244-01F

Image 34
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASTable of Contents Safety Information Product Identification Local Codes Optional Remote Control AccessoriesProduct Features UnpackingTools Required Phillips screwdriver Hood AssemblySheet Metal Screws Hood Louver Firebox Top Hex wrench ScissorsProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installation Check GAS TypeFireplace Clearances Installation ItemsBUILT-IN Fireplace Installation Minimum Clearance to Combustible MaterialsFront Width If you have not installed hood, follow instruc- tions onActual Framing Height DepthMantel Clearances for Built-In Installation Optional Mantel InstallationMantel Shelf Installing Optional Blower Accessory GA3450TA Switch Plate Installing Blower AccessorySwitch Plate Wire Remote Blower Harness Bracket CordTest to make sure blower is working properly For Built-In InstallationLower louver Connecting to GAS Supply Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Gas Regulator or Equipment Gas Control Valve Correct all leaks at onceEquipment Open Shutoff Valve Closed Gas MeterInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Optional Wall MountedRemove jumper wire from control valve see , Feed wires through rectangular slotsTerminal W Terminal R R Left Brick Liner Log Shoulder Screw Brick Liner Bracket ScreenRear Brick Liner Log SetLighting Instructions For Your Safety Read Before LightingOperating Fireplace Ignitor Button Control KnobThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Operating BlowerAUTO/OFF/ON Switch REMOTE-READY Models For Your Safety Read Before LightingPiezo Flame Control Ignitor Adjustment Knob Button Pilot Ignitor Burner Electrode If Using Optional Hand-Held RemoteOptional HAND-HELD Remote Operation Pilot Burner Ignitor ElectrodeON/OFF Series Model HRC100 Manual ModeAuto Thermostatic Mode Thermostat Series Model HRC200 SeriesOptional GWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted SwitchInspecting Burners Pilot Flame PatternBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceBurner Flame Pattern If pilot flame pattern is incorrect, as shown in ,Cabinet Wiring DiagramLOG SET Remote-Ready Models OnlyIgnitor cable pinched or wet TroubleshootingObserved Problem Possible Cause Remedy Ignitor cable dryModels Only Burner orifice is cloggedMote-Ready Models Only Or replace burner orificeMote-Ready Models Only Power is low When heated, vapors fromWalls or furniture Cleaners, etc. may turn into Slight smoke or odor duringErs, chemicals, new carpet Gas odor even when controlFireplace produces unwanted Ment aboveDimensions H x W x D including hood SpecificationsThermostat Models Technical Service Replacement PartsService Hints Parts Under WarrantyIllustrated Parts Breakdown Parts List Cdcfpr Outer Casing Firebox Models Cdcfnr and Cdcfpr104281-02BR Firebox Hood Firebox Top Illustrated Parts Breakdown Hardware Pack Brass Flare Adapter FittingLighting Instruction Plate Not a field replaceable part FDCFTN/TP VDCFRN/RP CDCFNR/PR Lighting Instruction Plate Equipment Shutoff Valve GA5010 AccessoriesTHERMOSTAT-CONTROLLED Blower KIT GA3450TA Brass Trim KIT GA6095Receiver and HAND-HELD Remote Control KIT HRC100 Series WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Information Video111244-01F 111244-01F 111244-01

CDCFTNA, CDCFPR, CDCFTPA specifications

Desa CDCFTPA, CDCFPR, and CDCFTNA represent a suite of advanced technologies and methodologies employed in the development and management of efficient distribution networks within the field of telecommunications and data services. These frameworks are designed to enhance connectivity, streamline processes, and ensure optimal performance in various environments.

One main feature of Desa CDCFTPA (Coaxial Digital Channel Fiber Transmission Protocol Architecture) is its ability to integrate coaxial cables with fiber optic technology, enabling high-speed data transmission over existing infrastructures. This hybrid approach not only reduces the need for extensive renovations but also capitalizes on the advantages of both technologies, offering broadband accessibility and improved bandwidth capabilities. By leveraging both mediums, operators can deliver enhanced services while maintaining cost-efficiency.

CDCFPR (Centralized Data Control Fiber Processing Resource) represents a centralized approach to managing data flow within telecommunications networks. Its core characteristic lies in its architecture, which supports dynamic allocation of resources in real-time. This enables network operators to efficiently allocate bandwidth based on demand, optimize routing paths, and reduce latency. Additionally, CDCFPR employs advanced algorithms for data compression and encryption, ensuring that users experience a seamless and secure connection.

CDCFTNA (Carrier Digital Channel Fiber Transmission Network Architecture) is focused on creating robust networks that can support a variety of distribution channels, including 5G and IoT devices. Its design emphasizes scalability and adaptability, allowing network providers to easily expand or modify their infrastructure to meet evolving market needs. Key technologies incorporated in CDCFTNA include Software-Defined Networking (SDN) and Network Function Virtualization (NFV), which enable operators to manage their resources more flexibly and efficiently.

Each of these frameworks boasts unique characteristics that contribute to the overall enhancement of telecommunications systems. They embody a commitment to innovation, sustainability, and user-centric design, aligning with current trends in digital services and communication technologies. By deploying such advanced systems, service providers can ensure they remain competitive in a fast-paced and continuously evolving market. In summary, Desa CDCFTPA, CDCFPR, and CDCFTNA collectively represent the future of telecommunications infrastructure, promising improved connectivity, efficiency, and adaptability for a diverse range of applications.