Desa CDCFTNA Hood Assembly, Sheet Metal Screws Hood Louver Firebox Top, Hex wrench Scissors

Page 6

HOOD ASSEMBLY

WARNING: Always have screen in place before operating fireplace. This prevents exces- sive temperatures on fireplace surfaces.

Sheet Metal Screws

Hood

Louver

Firebox

Top

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this fireplace may result in prop- erty damage or personal injury.

Tools Required:

 

 

•

Phillips screwdriver

•

slotted screwdriver

•

5/16" hex wrench

•

scissors

1.Models with one-piece screen only: Lift fireplace screen up and pull out to remove (see Figure 3). Set screen aside until installation has been completed.

2.Cut two plastic straps to remove the log from the firebox cavity. Set log aside.

3.An optional blower is available. See Acces- sories, page 44. Install optional blower now. Follow installation instructions provided with blower and see page 14 or 15, depending on your installation.

4.Locate four black phillips sheet metal screws in hardware packet.

5.Slide hood between louver and firebox top and align screw holes.

6.Insert screws as shown in Figure 4. Tighten screws firmly.

Shoulder Screw

Screen

Figure 4 - Assembling Hood

AIR FOR COMBUSTION AND VENTILATION

WARNING: This fireplace shall not be installed in a con- fined space or unusually tight construction unless provisions are provided for adequate com- bustion and ventilation air. Read the following instructions to in- sure proper fresh air for this and other fuel-burning appliances in your home.

Todayʼs homes are built more energy efficient than ever. New materials, increased insulation, and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible.

While it is good to make your home energy effi- cient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, fireplaces, clothes dryers, and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

Figure 3 - Removing and Installing

Screen

6

www.desatech.com

111244-01F

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASTable of Contents Safety Information Product Identification Local Codes Optional Remote Control AccessoriesProduct Features UnpackingTools Required Phillips screwdriver Hood AssemblySheet Metal Screws Hood Louver Firebox Top Hex wrench ScissorsAIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Check GAS TypeFireplace Clearances Installation ItemsBUILT-IN Fireplace Installation Minimum Clearance to Combustible MaterialsFront Width If you have not installed hood, follow instruc- tions onActual Framing Height DepthOptional Mantel Installation Mantel Clearances for Built-In InstallationMantel Shelf Installing Optional Blower Accessory GA3450TA Switch Plate Installing Blower AccessorySwitch Plate Wire Remote Blower Harness Bracket CordFor Built-In Installation Test to make sure blower is working properlyLower louver Connecting to GAS Supply Connecting Equipment Shutoff Valve to Heater Control Installation Items NeededChecking GAS Connections Gas Regulator or Equipment Gas Control Valve Correct all leaks at onceEquipment Open Shutoff Valve Closed Gas MeterInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Optional Wall MountedFeed wires through rectangular slots Remove jumper wire from control valve see ,Terminal W Terminal R R Left Brick Liner Log Shoulder Screw Brick Liner Bracket ScreenRear Brick Liner Log SetLighting Instructions For Your Safety Read Before LightingOperating Fireplace Ignitor Button Control KnobThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Operating BlowerREMOTE-READY Models For Your Safety Read Before Lighting AUTO/OFF/ON SwitchPiezo Flame Control Ignitor Adjustment Knob Button Pilot Ignitor Burner Electrode If Using Optional Hand-Held RemoteOptional HAND-HELD Remote Operation Pilot Burner Ignitor ElectrodeON/OFF Series Model HRC100 Manual ModeAuto Thermostatic Mode Thermostat Series Model HRC200 SeriesOptional GWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted SwitchInspecting Burners Pilot Flame PatternBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceBurner Flame Pattern If pilot flame pattern is incorrect, as shown in ,Cabinet Wiring DiagramLOG SET Remote-Ready Models OnlyIgnitor cable pinched or wet TroubleshootingObserved Problem Possible Cause Remedy Ignitor cable dryModels Only Burner orifice is cloggedMote-Ready Models Only Or replace burner orificeMote-Ready Models Only Power is low When heated, vapors fromWalls or furniture Cleaners, etc. may turn into Slight smoke or odor duringErs, chemicals, new carpet Gas odor even when controlFireplace produces unwanted Ment aboveSpecifications Dimensions H x W x D including hoodThermostat Models Technical Service Replacement PartsService Hints Parts Under WarrantyIllustrated Parts Breakdown Parts List Cdcfpr Firebox Models Cdcfnr and Cdcfpr Outer Casing104281-02BR Firebox Hood Firebox Top Illustrated Parts Breakdown Brass Flare Adapter Fitting Hardware PackLighting Instruction Plate Not a field replaceable part FDCFTN/TP VDCFRN/RP CDCFNR/PR Lighting Instruction Plate Equipment Shutoff Valve GA5010 AccessoriesTHERMOSTAT-CONTROLLED Blower KIT GA3450TA Brass Trim KIT GA6095Receiver and HAND-HELD Remote Control KIT HRC100 Series WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Information Video111244-01F 111244-01F 111244-01

CDCFTNA, CDCFPR, CDCFTPA specifications

Desa CDCFTPA, CDCFPR, and CDCFTNA represent a suite of advanced technologies and methodologies employed in the development and management of efficient distribution networks within the field of telecommunications and data services. These frameworks are designed to enhance connectivity, streamline processes, and ensure optimal performance in various environments.

One main feature of Desa CDCFTPA (Coaxial Digital Channel Fiber Transmission Protocol Architecture) is its ability to integrate coaxial cables with fiber optic technology, enabling high-speed data transmission over existing infrastructures. This hybrid approach not only reduces the need for extensive renovations but also capitalizes on the advantages of both technologies, offering broadband accessibility and improved bandwidth capabilities. By leveraging both mediums, operators can deliver enhanced services while maintaining cost-efficiency.

CDCFPR (Centralized Data Control Fiber Processing Resource) represents a centralized approach to managing data flow within telecommunications networks. Its core characteristic lies in its architecture, which supports dynamic allocation of resources in real-time. This enables network operators to efficiently allocate bandwidth based on demand, optimize routing paths, and reduce latency. Additionally, CDCFPR employs advanced algorithms for data compression and encryption, ensuring that users experience a seamless and secure connection.

CDCFTNA (Carrier Digital Channel Fiber Transmission Network Architecture) is focused on creating robust networks that can support a variety of distribution channels, including 5G and IoT devices. Its design emphasizes scalability and adaptability, allowing network providers to easily expand or modify their infrastructure to meet evolving market needs. Key technologies incorporated in CDCFTNA include Software-Defined Networking (SDN) and Network Function Virtualization (NFV), which enable operators to manage their resources more flexibly and efficiently.

Each of these frameworks boasts unique characteristics that contribute to the overall enhancement of telecommunications systems. They embody a commitment to innovation, sustainability, and user-centric design, aligning with current trends in digital services and communication technologies. By deploying such advanced systems, service providers can ensure they remain competitive in a fast-paced and continuously evolving market. In summary, Desa CDCFTPA, CDCFPR, and CDCFTNA collectively represent the future of telecommunications infrastructure, promising improved connectivity, efficiency, and adaptability for a diverse range of applications.
Top Page Image Contents