Desa CDCFPR Operating Fireplace, For Your Safety Read Before Lighting, Lighting Instructions

Page 22

INSTALLATION

Continued

6.Insert first rod into hole in left side of firebox. Fasten rod to rear hole near center of firebox using black Phillips head screw (see Figure 40, page 21).

7.Insert other rod into hole on right side of fire- box and fasten rod to front hole near center of firebox using remaining sheet metal screw.

OPERATING FIREPLACE

THERMOSTAT-CONTROLLED MODELS

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result causing property damage, per- sonal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighborʼs phone. Follow the gas supplierʼs instructions.

•If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, donʼt try to repair it, call a qualified service tech- nician or gas supplier. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified ser- vice technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

WARNING:You must operate this fireplace with the screen in place. Make sure fireplace screen is installed before run- ning fireplace.

NOTICE: During initial opera- tion of new fireplace, burning logs will give off a paper-burn- ing smell. Open window to vent smell. Operate fireplace on HI position to burn off odor. This will only last a few hours.

1.STOP! Read the safety information starting in column 1.

2.Make sure equipment shutoff valve is fully open.

3.Turn control knob clockwise to the OFF position.

4.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information in column 1. If you donʼt smell gas, go to the next step.

5.Turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds (see Figure 41).

Note: You may be running this fireplace for the first time after hooking up to gas sup- ply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

•If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Ignitor Button

 

 

Control Knob

 

 

 

 

 

 

 

Figure 41 - Control Knob In The OFF

Position

22

www.desatech.com

111244-01F

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASTable of Contents Safety Information Product Identification Local Codes Optional Remote Control AccessoriesProduct Features UnpackingTools Required Phillips screwdriver Hood AssemblySheet Metal Screws Hood Louver Firebox Top Hex wrench ScissorsProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installation Check GAS TypeFireplace Clearances Installation ItemsBUILT-IN Fireplace Installation Minimum Clearance to Combustible MaterialsFront Width If you have not installed hood, follow instruc- tions onActual Framing Height DepthMantel Clearances for Built-In Installation Optional Mantel InstallationMantel Shelf Installing Optional Blower Accessory GA3450TA Switch Plate Installing Blower AccessorySwitch Plate Wire Remote Blower Harness Bracket CordTest to make sure blower is working properly For Built-In InstallationLower louver Connecting to GAS Supply Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Gas Regulator or Equipment Gas Control Valve Correct all leaks at onceEquipment Open Shutoff Valve Closed Gas MeterInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Optional Wall MountedRemove jumper wire from control valve see , Feed wires through rectangular slotsTerminal W Terminal R R Left Brick Liner Log Shoulder Screw Brick Liner Bracket ScreenRear Brick Liner Log SetLighting Instructions For Your Safety Read Before LightingOperating Fireplace Ignitor Button Control KnobThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Operating BlowerAUTO/OFF/ON Switch REMOTE-READY Models For Your Safety Read Before LightingPiezo Flame Control Ignitor Adjustment Knob Button Pilot Ignitor Burner Electrode If Using Optional Hand-Held RemoteOptional HAND-HELD Remote Operation Pilot Burner Ignitor ElectrodeON/OFF Series Model HRC100 Manual ModeAuto Thermostatic Mode Thermostat Series Model HRC200 SeriesOptional GWMT1 Wall Mounted Thermostat Optional GWMS2 Wall Mounted SwitchInspecting Burners Pilot Flame PatternBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceBurner Flame Pattern If pilot flame pattern is incorrect, as shown in ,Cabinet Wiring DiagramLOG SET Remote-Ready Models OnlyIgnitor cable pinched or wet TroubleshootingObserved Problem Possible Cause Remedy Ignitor cable dryModels Only Burner orifice is cloggedMote-Ready Models Only Or replace burner orificeMote-Ready Models Only Power is low When heated, vapors fromWalls or furniture Cleaners, etc. may turn into Slight smoke or odor duringErs, chemicals, new carpet Gas odor even when controlFireplace produces unwanted Ment aboveDimensions H x W x D including hood SpecificationsThermostat Models Technical Service Replacement PartsService Hints Parts Under WarrantyIllustrated Parts Breakdown Parts List Cdcfpr Outer Casing Firebox Models Cdcfnr and Cdcfpr104281-02BR Firebox Hood Firebox Top Illustrated Parts Breakdown Hardware Pack Brass Flare Adapter FittingLighting Instruction Plate Not a field replaceable part FDCFTN/TP VDCFRN/RP CDCFNR/PR Lighting Instruction Plate Equipment Shutoff Valve GA5010 AccessoriesTHERMOSTAT-CONTROLLED Blower KIT GA3450TA Brass Trim KIT GA6095Receiver and HAND-HELD Remote Control KIT HRC100 Series WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Information Video111244-01F 111244-01F 111244-01

CDCFTNA, CDCFPR, CDCFTPA specifications

Desa CDCFTPA, CDCFPR, and CDCFTNA represent a suite of advanced technologies and methodologies employed in the development and management of efficient distribution networks within the field of telecommunications and data services. These frameworks are designed to enhance connectivity, streamline processes, and ensure optimal performance in various environments.

One main feature of Desa CDCFTPA (Coaxial Digital Channel Fiber Transmission Protocol Architecture) is its ability to integrate coaxial cables with fiber optic technology, enabling high-speed data transmission over existing infrastructures. This hybrid approach not only reduces the need for extensive renovations but also capitalizes on the advantages of both technologies, offering broadband accessibility and improved bandwidth capabilities. By leveraging both mediums, operators can deliver enhanced services while maintaining cost-efficiency.

CDCFPR (Centralized Data Control Fiber Processing Resource) represents a centralized approach to managing data flow within telecommunications networks. Its core characteristic lies in its architecture, which supports dynamic allocation of resources in real-time. This enables network operators to efficiently allocate bandwidth based on demand, optimize routing paths, and reduce latency. Additionally, CDCFPR employs advanced algorithms for data compression and encryption, ensuring that users experience a seamless and secure connection.

CDCFTNA (Carrier Digital Channel Fiber Transmission Network Architecture) is focused on creating robust networks that can support a variety of distribution channels, including 5G and IoT devices. Its design emphasizes scalability and adaptability, allowing network providers to easily expand or modify their infrastructure to meet evolving market needs. Key technologies incorporated in CDCFTNA include Software-Defined Networking (SDN) and Network Function Virtualization (NFV), which enable operators to manage their resources more flexibly and efficiently.

Each of these frameworks boasts unique characteristics that contribute to the overall enhancement of telecommunications systems. They embody a commitment to innovation, sustainability, and user-centric design, aligning with current trends in digital services and communication technologies. By deploying such advanced systems, service providers can ensure they remain competitive in a fast-paced and continuously evolving market. In summary, Desa CDCFTPA, CDCFPR, and CDCFTNA collectively represent the future of telecommunications infrastructure, promising improved connectivity, efficiency, and adaptability for a diverse range of applications.
Top Page Image Contents