Desa CDCFPR Optional Wireless HAND-HELD Remote Control Accessories, Optional Wall Mounted

Page 19

INSTALLATION

Continued

OPTIONAL WIRELESS HAND-HELD

REMOTE CONTROL ACCESSORIES

Remote-Ready Models Only

(HRC100 Series & HRC200 Series)

Installing Receiver

1.Disconnect wires from the control valve (see Figure 29) .

2.Locate the battery clip mounted on the back of the receiver (see Figure 30).

3.Slide 9-volt battery (not included) through the clip.

4.Attach the terminal wires to the battery (see Figure 30).

5.Connect wires from remote receiver to control valve as shown in Figure 31.

6.Install remote receiver unit onto remote/ blower bracket using screws provided (see Figure 31).

Figure 29 - Disconnecting Wires From

Control Valve

Receiver

9-Volt

Terminal

Battery

Wires

 

Battery Clip

Figure 30 - Attaching Battery to Receiver

White Wire to

TH Terminal on

Control Valve

Remote

Receiver

Red Wire to

TPTH Terminal on

Control Valve

Figure 31 - Installing Remote Receiver

Installing 9-Volt Battery in Hand-Held Remote Control Unit

1.Remove battery cover on back of remote control unit.

2.Attach terminal wires to the battery (not includ- ed). Place battery into the battery housing.

3.Replace battery cover onto remote control unit.

 

Remote

Battery

Control Unit

Cover

 

Terminal

 

Wires

 

9-Volt

Battery

Housing

Battery

 

Figure 32 - Installing Battery in Hand-

Held Remote Control Unit

OPTIONAL WALL MOUNTED

THERMOSTAT - GWMT1

 

(Remote-Ready Models Only)

WARNING: Read and fol-

low installation instructions.

Installation should be done by

a qualified installer familiar with

low-voltage wiring procedures.

WARNING: Do not connect

this thermostat to any electrical

source! Electrical shock and/or

fire hazard will occur.

 

1.Remove jumper wire from control valve (see Figure 39).

2.Connect one terminal of 25 ft. wire to the “TH” terminal on the control valve. Connect the other terminal to the “THTP” terminal on the control valve. See Figure 33.

Control Valve

To Wall Thermostat or Switch

To Wall

Thermostat

or Switch

Figure 33 - Connecting Wire Terminals

111244-01F

www.desatech.com

19

Image 19
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Product Identification Unpacking Optional Remote Control AccessoriesProduct Features Local CodesHex wrench Scissors Hood AssemblySheet Metal Screws Hood Louver Firebox Top Tools Required Phillips screwdriverProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationMinimum Clearance to Combustible Materials Installation ItemsBUILT-IN Fireplace Installation Fireplace ClearancesDepth If you have not installed hood, follow instruc- tions onActual Framing Height Front WidthMantel Clearances for Built-In Installation Optional Mantel InstallationMantel Shelf Installing Optional Blower Accessory GA3450TA Cord Installing Blower AccessorySwitch Plate Wire Remote Blower Harness Bracket Switch PlateTest to make sure blower is working properly For Built-In InstallationLower louver Connecting to GAS Supply Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Gas Meter Correct all leaks at onceEquipment Open Shutoff Valve Closed Gas Regulator or Equipment Gas Control ValveOptional Wall Mounted Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Installing 9-Volt Battery in Hand-Held Remote Control UnitRemove jumper wire from control valve see , Feed wires through rectangular slotsTerminal W Terminal R R Log Set Log Shoulder Screw Brick Liner Bracket ScreenRear Brick Liner Left Brick LinerIgnitor Button Control Knob For Your Safety Read Before LightingOperating Fireplace Lighting InstructionsOperating Blower Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationAUTO/OFF/ON Switch REMOTE-READY Models For Your Safety Read Before LightingPiezo Flame Control Ignitor Adjustment Knob Button Pilot Burner Ignitor Electrode If Using Optional Hand-Held RemoteOptional HAND-HELD Remote Operation Pilot Ignitor Burner ElectrodeThermostat Series Model HRC200 Series Manual ModeAuto Thermostatic Mode ON/OFF Series Model HRC100Pilot Flame Pattern Optional GWMS2 Wall Mounted SwitchInspecting Burners Optional GWMT1 Wall Mounted ThermostatIf pilot flame pattern is incorrect, as shown in , Cleaning MaintenanceBurner Flame Pattern Burner Injector Holder and Pilot AIR Inlet HoleRemote-Ready Models Only Wiring DiagramLOG SET CabinetIgnitor cable dry TroubleshootingObserved Problem Possible Cause Remedy Ignitor cable pinched or wetOr replace burner orifice Burner orifice is cloggedMote-Ready Models Only Models OnlySlight smoke or odor during When heated, vapors fromWalls or furniture Cleaners, etc. may turn into Mote-Ready Models Only Power is lowMent above Gas odor even when controlFireplace produces unwanted Ers, chemicals, new carpetDimensions H x W x D including hood SpecificationsThermostat Models Parts Under Warranty Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown Parts List Cdcfpr Outer Casing Firebox Models Cdcfnr and Cdcfpr104281-02BR Firebox Hood Firebox Top Illustrated Parts Breakdown Hardware Pack Brass Flare Adapter FittingLighting Instruction Plate Not a field replaceable part FDCFTN/TP VDCFRN/RP CDCFNR/PR Lighting Instruction Plate Brass Trim KIT GA6095 AccessoriesTHERMOSTAT-CONTROLLED Blower KIT GA3450TA Equipment Shutoff Valve GA5010Information Video WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Remote Control KIT HRC100 Series111244-01F 111244-01F 111244-01

CDCFTNA, CDCFPR, CDCFTPA specifications

Desa CDCFTPA, CDCFPR, and CDCFTNA represent a suite of advanced technologies and methodologies employed in the development and management of efficient distribution networks within the field of telecommunications and data services. These frameworks are designed to enhance connectivity, streamline processes, and ensure optimal performance in various environments.

One main feature of Desa CDCFTPA (Coaxial Digital Channel Fiber Transmission Protocol Architecture) is its ability to integrate coaxial cables with fiber optic technology, enabling high-speed data transmission over existing infrastructures. This hybrid approach not only reduces the need for extensive renovations but also capitalizes on the advantages of both technologies, offering broadband accessibility and improved bandwidth capabilities. By leveraging both mediums, operators can deliver enhanced services while maintaining cost-efficiency.

CDCFPR (Centralized Data Control Fiber Processing Resource) represents a centralized approach to managing data flow within telecommunications networks. Its core characteristic lies in its architecture, which supports dynamic allocation of resources in real-time. This enables network operators to efficiently allocate bandwidth based on demand, optimize routing paths, and reduce latency. Additionally, CDCFPR employs advanced algorithms for data compression and encryption, ensuring that users experience a seamless and secure connection.

CDCFTNA (Carrier Digital Channel Fiber Transmission Network Architecture) is focused on creating robust networks that can support a variety of distribution channels, including 5G and IoT devices. Its design emphasizes scalability and adaptability, allowing network providers to easily expand or modify their infrastructure to meet evolving market needs. Key technologies incorporated in CDCFTNA include Software-Defined Networking (SDN) and Network Function Virtualization (NFV), which enable operators to manage their resources more flexibly and efficiently.

Each of these frameworks boasts unique characteristics that contribute to the overall enhancement of telecommunications systems. They embody a commitment to innovation, sustainability, and user-centric design, aligning with current trends in digital services and communication technologies. By deploying such advanced systems, service providers can ensure they remain competitive in a fast-paced and continuously evolving market. In summary, Desa CDCFTPA, CDCFPR, and CDCFTNA collectively represent the future of telecommunications infrastructure, promising improved connectivity, efficiency, and adaptability for a diverse range of applications.