Desa CDCFTPA, CDCFTNA Replacement Parts, Service Hints, Technical Service, Parts Under Warranty

Page 35

REPLACEMENT PARTS

Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they canʼt supply original replacement part(s), call DESA Heating Productsʼ Technical Service Department at 1-866-672-6040.

When calling DESA Heating Products, have ready

•your name

•your address

•model and serial numbers of your fireplace

•how fireplace was malfunctioning

•type of gas used (propane/LP or natural gas)

•purchase date

Usually, we will ask you to return the part to the factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they canʼt supply original replacement part(s), call DESA Heating Products at 1-866-672-6040 for referral information.

When calling DESA Heating Products, have ready

•model number of your fireplace

•the replacement part number

SERVICE HINTS

When Gas Pressure Is Too Low

•pilot will not stay lit

•burners will have delayed ignition

•fireplace will not produce specified heat

•for propane/LP units, propane/LP gas supply may be low

You may feel your gas pressure is too low. If so, con- tact your local natural or propane/LP gas supplier.

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. If so, contact DESA Heating ProductsʼTechnical Service Department at 1-866-672-6040. When calling, please have your model and serial numbers of your heater ready.

You can also visit DESA Heating Productsʼtechni- cal services web site at www.desatech.com.

111244-01F

www.desatech.com

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Product Identification Unpacking Optional Remote Control AccessoriesProduct Features Local CodesHex wrench Scissors Hood AssemblySheet Metal Screws Hood Louver Firebox Top Tools Required Phillips screwdriverDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationProviding Adequate Ventilation Ventilation Air From Outdoors Ventilation AIRVentilation Air From Inside Building Check GAS Type InstallationMinimum Clearance to Combustible Materials Installation ItemsBUILT-IN Fireplace Installation Fireplace ClearancesDepth If you have not installed hood, follow instruc- tions onActual Framing Height Front WidthMantel Shelf Optional Mantel InstallationMantel Clearances for Built-In Installation Installing Optional Blower Accessory GA3450TA Cord Installing Blower AccessorySwitch Plate Wire Remote Blower Harness Bracket Switch PlateLower louver For Built-In InstallationTest to make sure blower is working properly Connecting to GAS Supply Checking GAS Connections Connecting Equipment Shutoff Valve to Heater ControlInstallation Items Needed Gas Meter Correct all leaks at onceEquipment Open Shutoff Valve Closed Gas Regulator or Equipment Gas Control ValveOptional Wall Mounted Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Installing 9-Volt Battery in Hand-Held Remote Control UnitTerminal W Terminal R R Feed wires through rectangular slotsRemove jumper wire from control valve see , Log Set Log Shoulder Screw Brick Liner Bracket ScreenRear Brick Liner Left Brick LinerIgnitor Button Control Knob For Your Safety Read Before LightingOperating Fireplace Lighting InstructionsOperating Blower Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationPiezo Flame Control Ignitor Adjustment Knob Button REMOTE-READY Models For Your Safety Read Before LightingAUTO/OFF/ON Switch Pilot Burner Ignitor Electrode If Using Optional Hand-Held RemoteOptional HAND-HELD Remote Operation Pilot Ignitor Burner ElectrodeThermostat Series Model HRC200 Series Manual ModeAuto Thermostatic Mode ON/OFF Series Model HRC100Pilot Flame Pattern Optional GWMS2 Wall Mounted SwitchInspecting Burners Optional GWMT1 Wall Mounted ThermostatIf pilot flame pattern is incorrect, as shown in , Cleaning MaintenanceBurner Flame Pattern Burner Injector Holder and Pilot AIR Inlet HoleRemote-Ready Models Only Wiring DiagramLOG SET CabinetIgnitor cable dry TroubleshootingObserved Problem Possible Cause Remedy Ignitor cable pinched or wetOr replace burner orifice Burner orifice is cloggedMote-Ready Models Only Models OnlySlight smoke or odor during When heated, vapors fromWalls or furniture Cleaners, etc. may turn into Mote-Ready Models Only Power is lowMent above Gas odor even when controlFireplace produces unwanted Ers, chemicals, new carpetThermostat Models SpecificationsDimensions H x W x D including hood Parts Under Warranty Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown Parts List Cdcfpr 104281-02BR Firebox Hood Firebox Top Firebox Models Cdcfnr and CdcfprOuter Casing Illustrated Parts Breakdown Lighting Instruction Plate Not a field replaceable part Brass Flare Adapter FittingHardware Pack FDCFTN/TP VDCFRN/RP CDCFNR/PR Lighting Instruction Plate Brass Trim KIT GA6095 AccessoriesTHERMOSTAT-CONTROLLED Blower KIT GA3450TA Equipment Shutoff Valve GA5010Information Video WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Remote Control KIT HRC100 Series111244-01F 111244-01F 111244-01

CDCFTNA, CDCFPR, CDCFTPA specifications

Desa CDCFTPA, CDCFPR, and CDCFTNA represent a suite of advanced technologies and methodologies employed in the development and management of efficient distribution networks within the field of telecommunications and data services. These frameworks are designed to enhance connectivity, streamline processes, and ensure optimal performance in various environments.

One main feature of Desa CDCFTPA (Coaxial Digital Channel Fiber Transmission Protocol Architecture) is its ability to integrate coaxial cables with fiber optic technology, enabling high-speed data transmission over existing infrastructures. This hybrid approach not only reduces the need for extensive renovations but also capitalizes on the advantages of both technologies, offering broadband accessibility and improved bandwidth capabilities. By leveraging both mediums, operators can deliver enhanced services while maintaining cost-efficiency.

CDCFPR (Centralized Data Control Fiber Processing Resource) represents a centralized approach to managing data flow within telecommunications networks. Its core characteristic lies in its architecture, which supports dynamic allocation of resources in real-time. This enables network operators to efficiently allocate bandwidth based on demand, optimize routing paths, and reduce latency. Additionally, CDCFPR employs advanced algorithms for data compression and encryption, ensuring that users experience a seamless and secure connection.

CDCFTNA (Carrier Digital Channel Fiber Transmission Network Architecture) is focused on creating robust networks that can support a variety of distribution channels, including 5G and IoT devices. Its design emphasizes scalability and adaptability, allowing network providers to easily expand or modify their infrastructure to meet evolving market needs. Key technologies incorporated in CDCFTNA include Software-Defined Networking (SDN) and Network Function Virtualization (NFV), which enable operators to manage their resources more flexibly and efficiently.

Each of these frameworks boasts unique characteristics that contribute to the overall enhancement of telecommunications systems. They embody a commitment to innovation, sustainability, and user-centric design, aligning with current trends in digital services and communication technologies. By deploying such advanced systems, service providers can ensure they remain competitive in a fast-paced and continuously evolving market. In summary, Desa CDCFTPA, CDCFPR, and CDCFTNA collectively represent the future of telecommunications infrastructure, promising improved connectivity, efficiency, and adaptability for a diverse range of applications.
Top Page Image Contents