Desa CDCFPR, CDCFTNA, CDCFTPA installation manual Product Identification

Page 4

SAFETY INFORMATION

Continued

1.

This appliance is only for use with the type of

 

gas indicated on the rating plate. This appliance

 

is not convertible for use with other gases.

2.

Do not place propane/LP supply tank(s) in-

 

side any structure. Locate propane/LP supply

 

tank(s) outdoors.

3.

If you smell gas

 

• shut off gas supply

 

• do not try to light any appliance

 

• do not touch any electrical switch; do not use

 

any phone in your building

 

• immediately call your gas supplier from a

 

neighborʼs phone. Follow the gas supplierʼs

 

instructions

 

• if you cannot reach your gas supplier, call

4.

the fire department

This fireplace shall not be installed in a bed-

 

room or bathroom.

5.

Do not use this fireplace as a wood-burning

 

fireplace. Use only the logs provided with

 

the fireplace.

6.

Do not add extra logs or ornaments such as

 

pine cones, vermiculite, or rock wool. Using

 

these added items can cause sooting. Do not

 

add lava rock around base. Rock and debris

 

could fall into the control area of fireplace.

7.

This fireplace is designed to be smokeless. If

 

logs ever appear to smoke, turn off fireplace

 

and call a qualified service person. Note:

 

During initial operation, slight smoking could

 

occur due to log curing and fireplace burning

 

manufacturing residues.

8.

To prevent the creation of soot, follow the

 

instructions in Cleaning and Maintenance,

 

page 28.

9.

Before using furniture polish, wax, carpet

12.Do not use this fireplace to cook food or burn paper or other objects.

13.Never place any objects in the fireplace or on logs.

14.Do not use fireplace if any part has been under water. Immediately call a qualified service technician to inspect the room fireplace and to replace any part of the control system and any gas control which has been under water.

15.Turn off and unplug fireplace and let cool before servicing. Only a qualified service person should service and repair fireplace.

16.Operating fireplace above elevations of 4,500 feet could cause pilot outage.

17.Do not operate fireplace if log is broken. Do not operate fireplace if log is chipped (dime- sized or larger).

18.To prevent performance problems, do not use pro- pane/LP fuel tank of less than 100 lbs. capacity.

19.Provide adequate clearances around air openings.

PRODUCT

IDENTIFICATION

Fireplace

Cabinet

Hood

Screen

Log

Ignitor Button

Control

 

Knob

cleaner, or similar products, turn fireplace off.

If heated, the vapors from these products may

create a white powder residue within burner

box or on adjacent walls or furniture.

10. This fireplace needs fresh air ventilation to run

properly. This fireplace has an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The

ODS shuts down the fireplace if not enough

fresh air is available. See Air for Combustion

and Ventilation, page 6. If fireplace keeps

shutting off, see Troubleshooting, page 30.

11. Do not run fireplace

• where flammable liquids or vapors are used

or stored.

Hood

 

Logs

 

Ignitor

 

Button

 

Remote

 

Control

Control

(Optional)

 

Knob

Fireplace Cabinet

• under dusty conditions.

Figure 1 - Vent-Free Compact Dual Flame Fireplace

4

www.desatech.com

111244-01F

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASTable of Contents Safety Information Product Identification Optional Remote Control Accessories Product FeaturesLocal Codes UnpackingHood Assembly Sheet Metal Screws Hood Louver Firebox TopTools Required Phillips screwdriver Hex wrench ScissorsProviding Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installation Check GAS TypeInstallation Items BUILT-IN Fireplace InstallationFireplace Clearances Minimum Clearance to Combustible MaterialsIf you have not installed hood, follow instruc- tions on Actual Framing HeightFront Width DepthMantel Clearances for Built-In Installation Optional Mantel InstallationMantel Shelf Installing Optional Blower Accessory GA3450TA Installing Blower Accessory Switch Plate Wire Remote Blower Harness BracketSwitch Plate CordTest to make sure blower is working properly For Built-In InstallationLower louver Connecting to GAS Supply Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlChecking GAS Connections Correct all leaks at once Equipment Open Shutoff Valve ClosedGas Regulator or Equipment Gas Control Valve Gas MeterOptional Wireless HAND-HELD Remote Control Accessories Installing ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wall MountedRemove jumper wire from control valve see , Feed wires through rectangular slotsTerminal W Terminal R R Log Shoulder Screw Brick Liner Bracket Screen Rear Brick LinerLeft Brick Liner Log SetFor Your Safety Read Before Lighting Operating FireplaceLighting Instructions Ignitor Button Control KnobManual Lighting Procedure To Turn OFF GAS To ApplianceThermostat Control Operation Operating BlowerAUTO/OFF/ON Switch REMOTE-READY Models For Your Safety Read Before LightingPiezo Flame Control Ignitor Adjustment Knob Button If Using Optional Hand-Held Remote Optional HAND-HELD Remote OperationPilot Ignitor Burner Electrode Pilot Burner Ignitor ElectrodeManual Mode Auto Thermostatic ModeON/OFF Series Model HRC100 Thermostat Series Model HRC200 SeriesOptional GWMS2 Wall Mounted Switch Inspecting BurnersOptional GWMT1 Wall Mounted Thermostat Pilot Flame PatternCleaning Maintenance Burner Flame PatternBurner Injector Holder and Pilot AIR Inlet Hole If pilot flame pattern is incorrect, as shown in ,Wiring Diagram LOG SETCabinet Remote-Ready Models OnlyTroubleshooting Observed Problem Possible Cause RemedyIgnitor cable pinched or wet Ignitor cable dryBurner orifice is clogged Mote-Ready Models OnlyModels Only Or replace burner orificeWhen heated, vapors from Walls or furniture Cleaners, etc. may turn intoMote-Ready Models Only Power is low Slight smoke or odor duringGas odor even when control Fireplace produces unwantedErs, chemicals, new carpet Ment aboveDimensions H x W x D including hood SpecificationsThermostat Models Replacement Parts Service HintsTechnical Service Parts Under WarrantyIllustrated Parts Breakdown Parts List Cdcfpr Outer Casing Firebox Models Cdcfnr and Cdcfpr104281-02BR Firebox Hood Firebox Top Illustrated Parts Breakdown Hardware Pack Brass Flare Adapter FittingLighting Instruction Plate Not a field replaceable part FDCFTN/TP VDCFRN/RP CDCFNR/PR Lighting Instruction Plate Accessories THERMOSTAT-CONTROLLED Blower KIT GA3450TAEquipment Shutoff Valve GA5010 Brass Trim KIT GA6095WALL-MOUNT Thermostat Switch GWMT1 WALL-MOUNT ON/OFF Switch GWMS2Receiver and HAND-HELD Remote Control KIT HRC100 Series Information Video111244-01F 111244-01F 111244-01

CDCFTNA, CDCFPR, CDCFTPA specifications

Desa CDCFTPA, CDCFPR, and CDCFTNA represent a suite of advanced technologies and methodologies employed in the development and management of efficient distribution networks within the field of telecommunications and data services. These frameworks are designed to enhance connectivity, streamline processes, and ensure optimal performance in various environments.

One main feature of Desa CDCFTPA (Coaxial Digital Channel Fiber Transmission Protocol Architecture) is its ability to integrate coaxial cables with fiber optic technology, enabling high-speed data transmission over existing infrastructures. This hybrid approach not only reduces the need for extensive renovations but also capitalizes on the advantages of both technologies, offering broadband accessibility and improved bandwidth capabilities. By leveraging both mediums, operators can deliver enhanced services while maintaining cost-efficiency.

CDCFPR (Centralized Data Control Fiber Processing Resource) represents a centralized approach to managing data flow within telecommunications networks. Its core characteristic lies in its architecture, which supports dynamic allocation of resources in real-time. This enables network operators to efficiently allocate bandwidth based on demand, optimize routing paths, and reduce latency. Additionally, CDCFPR employs advanced algorithms for data compression and encryption, ensuring that users experience a seamless and secure connection.

CDCFTNA (Carrier Digital Channel Fiber Transmission Network Architecture) is focused on creating robust networks that can support a variety of distribution channels, including 5G and IoT devices. Its design emphasizes scalability and adaptability, allowing network providers to easily expand or modify their infrastructure to meet evolving market needs. Key technologies incorporated in CDCFTNA include Software-Defined Networking (SDN) and Network Function Virtualization (NFV), which enable operators to manage their resources more flexibly and efficiently.

Each of these frameworks boasts unique characteristics that contribute to the overall enhancement of telecommunications systems. They embody a commitment to innovation, sustainability, and user-centric design, aligning with current trends in digital services and communication technologies. By deploying such advanced systems, service providers can ensure they remain competitive in a fast-paced and continuously evolving market. In summary, Desa CDCFTPA, CDCFPR, and CDCFTNA collectively represent the future of telecommunications infrastructure, promising improved connectivity, efficiency, and adaptability for a diverse range of applications.
Top Page Image Contents