Desa DCFTNA installation manual Fdcftn/Tp, Vdcfrn/Rp Cdcfnr/Pr

Ad

Page 42

ILLUSTRATED PARTS BREAKDOWN

REMOTE-READY MODELS

FDCFRN, FDCFRP, VDCFRN, VDCFRP, CDCFNR, CDCFPR

4

9

1 2

6

7

3

9

10

11

8	5

9

12 14

20 (FDCFTN/TP, VDCFRN/RP)

20 (CDCFNR/PR)

12

Natural

21Gas Only

22 15 16

I

H

	O
NO	FF
T

18

17

9

16

15

19

13

42

www.desatech.com

111244-01E

Image 42

Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASTable of Contents Safety Information Product Identification Provide adequate clearances around air openingsLocal Codes Optional Remote Control AccessoriesProduct Features UnpackingHood Assembly Tools Required Phillips screwdriverHex wrench Scissors AIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Check GAS TypeFireplace Clearances Installation ItemsBUILT-IN Fireplace Installation Minimum Clearance to Combustible MaterialsIf you have not installed hood, follow instruc- tions on DepthOptional Mantel Installation Mantel Clearances for Built-In InstallationAlign shim under adjusting plate as shown in Figure Installing Optional Blower Accessory GA3450TAReinstall top louver Remove packaging from three remaining pieces of trimInstalling Blower Accessory DoorFor Built-In Installation Test to make sure blower is working properlyLower louver Connecting to GAS Supply Sediment TrapConnecting Equipment Shutoff Valve to Heater Control Installation Items NeededChecking GAS Connections Correct all leaks at once Els or page 25 for Remote-Ready ModelsInstalling 9-Volt Battery in Hand-Held Remote Control Unit Optional Wireless HAND-HELD Remote Control AccessoriesInstalling Receiver Optional Wall MountedOptional Wall Switch GWMS2 Remote-Ready Models Only Remove jumper wire from control valve see ,Installing LOG SET and Screen Models with One-Piece Screen OnlyOperating Fireplace Lighting InstructionsThermostat Control Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Operating BlowerREMOTE-READY Models For Your Safety Read Before Lighting AUTO/OFF/ON Blower SwitchIf Using Optional Hand-Held Remote Optional HAND-HELD Remote OperationAuto Shutoff Feature Manual ModeAuto Thermostatic Mode ON/OFF Series Model CghrcbInspecting Burners Optional GWMS2 Wall Mounted SwitchKey Pad Lock Feature Optional GWMT1 Wall Mounted ThermostatBurner Injector Holder and Pilot AIR Inlet Hole Cleaning MaintenanceBurner Flame Pattern If burner ﬂame pattern is incorrect, as shown in FigureWiring Diagram LOG SETCabinet Ignitor cable pinched or wet TroubleshootingObserved Problem Possible Cause Remedy Ignitor cable dryModels Only Burner oriﬁce is cloggedMote-Ready Models Only Or replace burner oriﬁceMote-Ready Models Only Power is low When heated, vapors fromWalls or furniture Cleaners, etc. may turn into Slight smoke or odor duringErs, chemicals, new carpet Gas odor even when controlFireplace produces unwanted Ment aboveSpecifications Thermostat ModelsRemote-Ready Models Technical Service Replacement PartsService Hints Parts Under WarrantyIllustrated Parts Breakdown Parts List Illustrated Models Firebox Models CDCFNR, Cdcfpr Illustrated Parts Breakdown Thermostat Models FDCFTN/TP, VDCFRN/RP CDCFNR/PR REMOTE-READY Models Brass Trim KIT GA6095 AccessoriesEquipment Shutoff Valve GA5010 THERMOSTAT-CONTROLLED Blower KIT GA3450TACleaning KIT GCK/CCK WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Remote Control KIT Ghrcb and Cghrcb111244-01E 111244-01E Not a UPC