Manually Lighting Your Grill by Match
To light your gas grill by match, insert a match into the Manual Lighting Stick and follow steps 1 through 6 of the Basic Lighting Procedures. Then, light the match and place Manual Lighting Stick through the Lighting Hole on the left side of the grill. See Fig. 19. Turn the nearest Control Knob to the HiGH setting to release gas. The Burner should (ight immediately.
Figure 19
LIGHTING
HOLE
M&NUAL
LIGHTING
STICK _-
MATCH
z WARNING
Never lean over the grill cooking area while lighting your gas grill. Keep your face and body a safe distance (at least 18 inches) from the Lighting Hole or Burners, when lighting your grill by match.
If the grill fails to light :
1.Turn gas off at source and turn the Control Knob to OFF. Wait at least five minutes for gas to clear, then retry.
2.if your grill still fails to light, check gas supply and connections.
3.Repeat lighting procedure. If your grill still fails to operate, turn the gas off at source, turn the Control Knobs to OFF, then check the following:
•Misalignment of Burner Tubes over Orifices
Correction: Reposition Burner Tubes over Orifices.
•Obstruction in gas line
Correction: Remove fuel line from grill. Do not smoke! Open gas supply for one second to clear any obstruction from fuel line. Close off gas supply at source and reconnect fuel line to grill.
•Plugged Orifice
Correction: Remove Burners from grill by pulling Cotter Pin (beneath Burner) using Long nose pliers. Carefully lift each Burner up and away from gas valve Orifice. Remove the Orifice from gas valve and gently clear any obstruction with a fine wire. Then reinstall all Orifices, Burners, Cotter Pins and cooking components.
If an obstruction is suspected in gas valves or
gas valve bracket, _lease call for repair service at
•Obstruction in BurnerTubes
Correction: Follow the Burner Tube cleaning procedure on page 22 of this Owner'sManual.
•Misalignment of Ignitor on Burner Correction: Check for proper position of the Electrode Tip as shown in Figure 12 The gap between the Spark Electrode Tip and Burner or Spark Receiver should be approximately 3/16", Adjust if necessary. With the gas supply closed and all Control Knobs set to OFF press the Electric Ignitor Cap and check for the presence of a spark at the Electrode.
•Disconnected Ignition Wires
Correction: Inspect the Ignitor JunctionBox found behindthe Control Panel. Connect loose
Ignitorwires to Junction Box and try to light the grill.
Weak AA battery
Correction: Unscrew the Ignitor Cap and replace the battery.
4, If the grill still does not light you may need to purge air from the gas line or reset the regulator excess gas flow device. Note: This procedure should be done every time a new LP gas tank is connected to your grill.
To purge air from your gas line andlor reset the regulator excess gas flow device:
•Turn the Control Knobs to the OFF posi- tion.
•Turn off the gas at the tank valve.
•Disconnect regulator from LP gas tank.
•Let unit stand for 5 minutes.
•Reconnect regulator to the LP gas tank.
•Turn the tank valve on slowly until 1/4 to 1/2 open.
•Open the Grill Lid.
•Set Control Knobs to OFF
•Push and turn the LEFT Control Knob to HIGH.
. If all checks or corrections have been made and you still have questions about operating your gas grill, call the Customer Service Helpline 8am - 8pm CST, Monday through Friday at
WARNING
Should a "FLASHBACK" fire occur in/or around the Burner Tubes, follow the instructions below. Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily injury, death, or property damage.
•Shut off gas supply to the gas grill.
•Turn the Control Knobs to OFF position.
•Put out any flame with a proper fire extinguisher.
•Open Grill Lid.
•Once the grill has cooled down, clean the Burner Tubes and Burners according to the cleaning instructions found on page 21 in this manual.
20