Aussie 6122S8X641 Lighting the Grill Using the Piezo Ignitor, Manual Lighting of the Grill on

Page 27

27

Lighting the Grill Using the Piezo Ignitor (continued)

1.Open the Hood.

2.IMPORTANT: Make sure Control Knobs are turned “Off.” (Fig. 4)

3.Turn the LP Gas Cylinder valve open counterclockwise until it stops. (Fig. 5)

 

 

Turn LP Gas

 

Control Knob in High

Cylinder valve

Control Knob in

counterclockwise

position (large flame

Fig. 5

Off position

symbol)

 

Fig. 4

 

 

Side Burner

Control Knob

Piezo Igniter Button

Fig. 6

Left Main Burner

Control Knob

Right Main Burner

Control Knob

4.Push far left Main Burner Control Knob in on Control Panel and turn counterclockwise to the High position. (Figs. 4 and 6)

5.Push the Piezo Igniter Button several times so that it clicks each time. Look to make sure the Burner is lit. If no spark, see Troubleshooting Section on page 37.

6.From the “Off” position, light other Burner. Your grill has a Crossover Ignition System that allows the Burners to light successively off one another.

7.If the Burner fails to light, repeat Step 4. If it still does not light, try the right Burner.

If a Burner goes out during operation, turn all Control Knobs to the “Off” position and close the LP Gas Cylinder valve to dissipate any accumulated gas. Open Hood and wait five minutes before attempting to relight the grill.

If any or all Burners fail to light after three to four attempts following Steps 4-7, turn all Control Knobs to the “Off” position and close the LP Gas Cylinder valve to dissipate any accumulated gas. Wait five minutes; then repeat the lighting procedures.

NOTE: If the Burners still fail to light, refer to the Troubleshooting Section on page 38. The Burner can also be lit manually, see

Manual Lighting of the Grill on page 28.

Image 27
Contents For Outdoor Household Use Only. Not for Commercial Use 6122S8X6416112S8X641Carbon Monoxide Hazard Tools Required for AssemblyPreparation for Assembly ContentsParts Illustration Model 6122S8X641 Parts List- Model 6122S8X641 Key Description QuantityDescription Quantity Parts Illustration Model 6112S8X641 Parts List- Model 6112S8X641 Assembly Instructions Step Front Leg Frame AssemblyStep Rear Leg Frame Assembly Step Rear Crossbrace Assembly Step Side Table Support Assembly Step Cart Frame AssemblyStep Manifold and Piezo Igniter Assembly Step Heat Shield AssemblyStep Shroud Assembly Step Control Panel to Cart Frame AssemblyStep Wheel Assembly Step Shroud to Cart AssemblyModel 6122 only Side Burner Valve Assembly Step Side Tables to Cart AssemblyStep Drip Cup Wire Assembly Step Bowl to Cart AssemblyStep Main Burner Assembly Model 6122 only Side Burner Assembly Model 6122 only Side Burner Electrode AssemblyElectrode Wire Plug Assembly Step Main Burner Electrode AssemblyStep Hood/Hinge Assembly Step Hood Handle AssemblyStep Cooking Grid / Control Knob Assembly Step Flavor Activator / Warming Rack AssemblyStep Step Cylinder Blocking Wire AssemblyDrip Cup Assembly Cylinder Retainer Wire AssemblyConnecting/Disconnecting the Gas Using GasLP Gas Cylinder LP Hose and Regulator Connecting LP Gas CylinderPerforming a Leak Test Before Using Your LP Gas GrillInstallation Codes Selecting a LocationHow to Perform a Leak Test First Time USE and as required Check The Flame Lighting the Grill Using the Pulse-Spark IgnitorManual Lighting of the Grill on Lighting the Grill Using the Piezo IgnitorManually Lighting the Grill Lighting the Side Burner Model 6122 Only Manually Lighting the Side BurnerManually Lighting the Side Burner Grill Cooking Direct Method Cooking On the Gas GrillRoasting Indirect Method Direct Cooking on the GridsIndirect Cooking Roasting End of Cooking Session Warming RackCleaning the Grill Care and MaintenanceHow to Clean the Burners Screw Storage Emergencies TroubleshootingClean the Burners. See How to Clean Burners in Care MaintenanceSee How to Clean Burners in Care and Maintenance Important Notice ProblemMeco Corporation Limited Warranty Limited Warranty