Aussie 6805, 6804 manual Open up

Page 32

32

5.Use a pipe cleaner to clear insect nests from the inlet hole of Main Burner (Fig. 19) and Side Burner tube. (Fig. 20)

6.Open up the Main Burner holes (Fig. 19) and the Side Burner holes (Fig. 21) with a small nail or wire. Use a non- metallic brush to remove food particles and corrosion from the Burner surfaces.

 

Open up

Non-metallic

Main Burner

Wire Brush

holes with a

 

small nail or

 

wire.

Fig. 19

Pipe Cleaner

 

Fig. 21

Fig. 20

Side Burner tube

Make sure the screw holding the electrode underneath is tight so 3/16”gap between electrode tip and side burner is maintained.

Open up Burner holes with a small nail or wire.

7.Check the Side Burner Electrode to see if it is loose. If so, tighten the screw holding the Electrode to maintain 3/16” gap between Electrode tip and Side Burner.

NOTE: Before next step, you may wish to clean the rest of the grill. See Grill Body and Cabinet.

8. After cleaning, refit the Burners.

NOTE: When refitting the Burners, be sure each Burner is positioned correctly. The valves should protrude inside the Venturi ends of the Burner. (Fig. 18) Replace the Bolts and Nuts that fasten the Burner Flange to Back Wall.

9.If the grill is to be stored, wrap Burners in a protective cover to keep insects out.

10.Check Burner operation after re-assembly.

11.Replace Flame Diffusers and Cooking Grids.

NOTE: The sear burner and IR side burner, in the 6805, do not require manual cleaning. Do not scrape the ceramic with any sort of tool. Remove any large pieces of food after grill has cooled. If small amounts of food or grease fall on the ceramic, turn the burner on high for 2 to 5 minutes until the food or grease has turned to dust and disappeared from the ceramic.

Image 32
Contents 68046805 For Outdoor Household Use Only. Not for Commercial UseTools Required for Assembly Supplied with Grill Carbon Monoxide HazardContents Preparation for AssemblyPacking List- Model Box DescriptionPacking List- Model Step Cabinet Bottom Assembly Assembly InstructionsStep Caster Assembly Step Side Panel Assembly Step Front Crossbar Assembly Step Cabinet Upright AssemblyStep Cylinder Guard Assembly Cylinder Blocking Wire AssemblyCenter Wheel Assembly Model Door Handle Assembly StepStep Drawer Assembly Drawer PositioningStep Door Assembly Step Hood/Body To Cart AssemblyStep Side Table Assembly Side Burner Valve Assembly Side Burner Valve ConnectionSide Burner Grid Assembly Step Side Burner Igniter Wire ConnectionStep Side Burner Control Knob Assembly Step Warming Rack Assembly Step Bottom Body Panel AssemblyFoil Pan/Grease Pan Assembly Step Flame Diffuser/Cooking Grid Assembly Step Battery in Igniter InstallationLP Gas Cylinder Connecting/Disconnecting the GasUsing Gas Connecting LP Gas Cylinder LP Hose and RegulatorBefore Using Your LP Gas Grill Installation CodesSelecting a Location Performing a Leak TestHow to Perform a Leak Test First Time USE and as required Model Lighting the Grill Using the Pulse-Spark Ignitor Off positionLighting the Side Burner Sear Burner or Rotisserie Burner Manual Lighting of the Grill onManually Lighting the Grill Manually Lighting the Side Burner Lighting the Side BurnerCheck The Flame Manually Lighting the Side Burner Cooking On the Gas Grill Grill Cooking Direct MethodIndirect Cooking Roasting Roasting Indirect MethodDirect Cooking on the Grids Warming Rack End of Cooking SessionCare and Maintenance Cleaning the GrillHow to Clean the Burners Open up Storage Troubleshooting EmergenciesSee How to Clean Burners in Care and Maintenance Then stops when full Rises up while fillingParts Illustration- Model Parts List- Model Key Description QuantityParts Illustrations- Model Limited Warranty Meco Corporation Limited Warranty