Shoprider Wizz 888WNL, Streamer 888WAB manual Adjustment Procedures, Length, Angle, Height, Width

Page 15
ADJUSTMENT PROCEDURES

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

ADJUSTMENT PROCEDURES

FOOTREST ADJUSTMENTS (Fig. 9) STREAMER (888-WB/WAB/WSB) WIZZ (WNL)

LENGTH

Pull out the safety pin (1) from the first hole in the footrest slide tube (2), adjust the footrest slide tube and refit the safety pin in the hole at the desired length.

ANGLE

(3)

(2)(1)

Fig. 9

Release the lock nut and adjust the bolt under the footrest (3) to adjust the footrest angle. When the angle desired is reached, re-tighten the lock nut and bolt.

ARM ADJUSTMENTS (Fig.10) STREAMER (888-WB/WAB/WSB) WIZZ (888-WNL)

ANGLE

Pull up on the end of the armrests and they will flip back up allowing easy transfer in and out of the seat. Under the armrest there is a bolt and lock nut (1) that can be adjusted up or down to change the angle of the armrest.

LENGTH

(1)

(2)

(3)

Fig. 10

Located under each armrest is a hand knob (2). By turning counter-clockwise to release, the armrest can be extended and reset in position by re-tightening the hand knob.

HEIGHT

Below the armrest on the down supporting tube there is a screw and lock nut (3) that can be allowed for adjustments. Two aligned hex screws prevent any loose play.

WIDTH

Beneath the rear of the seat there are two hand knobs, one on each side. Release the hand knob and slide each arm assembly outward. Re-tighten the hand knob when in the desired position.

~14~

Image 15
Contents STREAMER 888WAB MEDICAL POWER WHEELCHAIRUser Manual STREAMER 888WBCONTENTS FEATURE GUIDE INTRODUCTIONWIZZ 888WNL STREAMER 888WAB STREAMER 888WB/888WSBJETSTREAM-L 888WAL JEETSTREAM-M 888WAMELECTROMAGNETIC INTERFERENCE EMI FROM RADIO WAVE SOURCES EMI WARNINGWARNINGS POWERCHAIR ELECTROMAGNETIC INTERFERENCE EMISAFETY INSTRUCTIONS SAFETY INSTRUCTIONS WARNING, CAUTION AND INDICATION LABEL LOCATION Joystick ControllerChassis Shroud of WIZZ 888WNL ~10~ WARNING,CAUTIONANDINDICATIONLABELLOCATIONChassis Shroud of STREAMER 888WAB Chassis Shroud of STREAMER 888WB/888WSBChassis Shroud of JETSTREAM-L/M 888WAL/888WAM ~11~YELLOW - CHARGING GREEN - CHARGED Fig. 8a PREPARATION FOR USE~13~ PROGRAMMABLE CONTROLLERHEIGHT ADJUSTMENT PROCEDURESLENGTH ANGLEFOOTREST ADJUSTMENTS Fig. 11 JETSTREAM-L/M 888-WAL/WAM Fastening Strap SEAT HEIGHT ADJUSTMENTS Fig.13SAFETY BELT AND FASTENING STRAP SETTING Fig.13 Safety BeltGETTING READY TO KNOW THE JOYSTICK CONTROLLER VSI On / Off Button OPERATION INSTRUCTIONSBattery Gauge Maximum Speed IndicatorCharging Port 8 for Off-Board Charger GETTING READY TO DRIVEENGAGED / DISENGAGED MODE COMPONENTS FOR JETSTREAM -L/M 888WAL/WAM DISASSEMBLY & ASSEMBLY INSTRUCTIONSCOMPONENTS FOR WIZZ 888WNL COMPONENTS FOR STREAMER 888WB/WAB/WSBTo reassemble the Powerchair, reverse the procedures described above DISASSEMBLY PROCEDURESBATTERIES & BATTERY CHARGING BATTERIESWARNING! Only use the original manufacturer approved charger 1. Grasp the charging port cover and remove it from the charging port ~23~ ~24~ TROUBLE SHOOTING~25~ ~26~ SPECIFICATION~27~ QUARTERLY INSPECTIONDISCLAIMER