Shoprider Wizz 888WNL, Steamer 888WSB Disassembly & Assembly Instructions, Disassembly Procedures

Page 21
DISASSEMBLY PROCEDURES

GMP

ISO9001

ISO14001

ISO13485

CERTIFIED

DISASSEMBLY & ASSEMBLY INSTRUCTIONS

DISASSEMBLY PROCEDURES

WARNING! We advise caution when disassembling and lifting items. You must ensure that the person undertaking these actions is able to handle the weight.

STEP 1 Ensure the area where the Powerchair is to be dismantled is spacious. STEP 2 Remove the plug at the end of the VSI cable by pulling on the pull ring.

CAUTION! Lay the plug down carefully, taking care not to damage the chassis shroud.

STEP 3 The arm assembly can be removed to make the seat assembly lighter to lift. Under the rear of the seat assembly there are two hand knobs. Release these by turning in a counter-clockwise direction and slide out the arm assembly from each side.

STEP 4 The seat assembly should be folded down for easier lifting.

STEP 5 For WIZZ (888WNL), loosen and take away the retaining pins from the four seat supporting posts beneath the seat assembly.

For STREAMER (888WB/888WAB/888WSB), release and take away the hand knob from the seat supporting post.

STEP 6 For JETSTREAM-L/M (888WAL/WAM), pull up on the two red tabs located under the rear of the seat and push the seat forward. Unscrew the two red handles located under the front of seat. Slide seat out.

STEP 7 Lift the seat assembly free of the chassis assembly.

STEP 8 Remove the chassis shroud by simply lifting up. You will find the shroud is held firm by Velcro tapes.

CAUTION! Care must be taken to slide the plug through the chassis shroud.

STEP 9 For WIZZ (888WNL), loosen and take away the two retaining pins securing the connection between front chassis assembly and rear chassis assembly.

STEP 10For STREAMER (888WB/888WAB/888WSB), loosen and take away the two retaining pins securing the connection between chassis assembly and anti-tip wheels assembly.

STEP 11Unclip the battery plugs (red and black). The batteries can now, with the help of carrying straps provided, be lifted from chassis.

To reassemble the Powerchair, reverse the procedures described above.

~20~

Page 20 Page 22
Image 21
Page 20 Page 22
Contents User Manual MEDICAL POWER WHEELCHAIRSTREAMER 888WB STREAMER 888WABCONTENTS FEATURE GUIDE INTRODUCTIONWIZZ 888WNL STREAMER 888WAB STREAMER 888WB/888WSBJETSTREAM-L 888WAL JEETSTREAM-M 888WAMELECTROMAGNETIC INTERFERENCE EMI FROM RADIO WAVE SOURCES EMI WARNINGWARNINGS POWERCHAIR ELECTROMAGNETIC INTERFERENCE EMISAFETY INSTRUCTIONS SAFETY INSTRUCTIONS WARNING, CAUTION AND INDICATION LABEL LOCATION Joystick ControllerChassis Shroud of WIZZ 888WNL Chassis Shroud of STREAMER 888WAB WARNING,CAUTIONANDINDICATIONLABELLOCATIONChassis Shroud of STREAMER 888WB/888WSB ~10~Chassis Shroud of JETSTREAM-L/M 888WAL/888WAM ~11~YELLOW - CHARGING GREEN - CHARGED Fig. 8a PREPARATION FOR USE~13~ PROGRAMMABLE CONTROLLERLENGTH ADJUSTMENT PROCEDURESANGLE HEIGHTFOOTREST ADJUSTMENTS Fig. 11 JETSTREAM-L/M 888-WAL/WAM SAFETY BELT AND FASTENING STRAP SETTING Fig.13 SEAT HEIGHT ADJUSTMENTS Fig.13Safety Belt Fastening StrapBattery Gauge OPERATION INSTRUCTIONSMaximum Speed Indicator GETTING READY TO KNOW THE JOYSTICK CONTROLLER VSI On / Off ButtonCharging Port 8 for Off-Board Charger GETTING READY TO DRIVEENGAGED / DISENGAGED MODE COMPONENTS FOR WIZZ 888WNL DISASSEMBLY & ASSEMBLY INSTRUCTIONSCOMPONENTS FOR STREAMER 888WB/WAB/WSB COMPONENTS FOR JETSTREAM -L/M 888WAL/WAMTo reassemble the Powerchair, reverse the procedures described above DISASSEMBLY PROCEDURESBATTERIES & BATTERY CHARGING BATTERIESWARNING! Only use the original manufacturer approved charger 1. Grasp the charging port cover and remove it from the charging port ~23~ ~24~ TROUBLE SHOOTING~25~ ~26~ SPECIFICATION~27~ QUARTERLY INSPECTIONDISCLAIMER
Top Page Image Contents