Pride Mobility 1420 manual Drive Program Select Key, To change the drive mode program

Page 37

V I I . O P E R A T I O N

Drive Program Select Key

The drive program select key enables you to select a drive program and an actuator mode. Your Dynamic DX controller was preprogrammed at the factory for five drive programs— 1(slowest) to 5(fastest). The drive mode is indicated by a number in the center of the keypad.

NOTE: The drive mode settings are preset at the factory. If your authorized Pride provider changes these settings, please make note of these changes.

To change the drive mode program:

1.Press the drive mode select key.

2.Move the joystick right to increase the drive mode program.

3.Move the joystick left to decrease the drive mode program.

4.Press the drive mode select key.

Drive Mode and Actuator Display (also Remote Status Display)

This is a seven-segment light that displays the drive program. It also displays a drive inhibit and actuator mode (if applicable), when they occur.

Actuator Select Keys with Lights

The actuator select keys can control up to five actuators independently. These actuators may control power elevating seats, power elevating leg rests, power reclining seats, or tilt-in-space seats. If your controller is programmed with drive inhibit during actuator operation, the drive inhibit symbol will be displayed during actuator operation. You control the actuators through the actuator select keys and the joystick.

To move an actuator:

1.Press an actuator select key.

2.Move the joystick beyond half its travel in either the forward or reverse direction to move the actuator. Forward moves the actuator up. Reverse moves the actuator down.

3.Press the actuator select key again to turn off the actuator.

Remote Status Light

This light will flash if there is an internal Dynamic DX Remote fault, or if an OONAPU fault has occurred. See “Out Of Neutral At Power Up.”

Horn Key

The horn key activates the horn.

Battery Saver Feature

When the battery capacity drops to below 21V (typically two lights), the controller will reduce power chair performance to conserve battery power.

Sleep Mode (If Enabled)

The power chair controller features a sleep mode. Sleep mode is a built-in circuit that will automatically shut off the main power if the joystick is not moved in any direction for a period of time. This time factor is programmed into the controller. To restore power and continue, push and key on the keypad.

Quantum Jazzy 1400 Series Rev D May04

www.pridemobility.com

37

Image 37
Contents Includes 1420 Copyright Pride Mobility Products Corp N T E N T S Introduction N T R O D U C T I O NInformationExchange PrideMobilityProductsCorporation AttnCustomerCareDepartmentMyAuthorizedPrideProviderIs Pride Owners ClubS a F E T Y Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationOutdoor Driving Surfaces Stationary Obstacles Steps, Curbs, etc Freewheel ModePublic Streets and Roadways Stairs and Escalators EMI & RFI Positioning Belts Inclement Weather Precautions Reaching and BendingBatteries Removable Parts AlcoholWhere do radio waves come from? Frequently Asked Questions FAQsAre all power chairs susceptible to EMI/RFI? I . E M I / R FWhat should I do if my power chair moves unexpectedly? What is the FDA doing about the problem?Quantum Jazzy 1420 1400 is similar T H E Q UA N T U M JA Z Z Y 1 4 0 0 S E R I E SSpecifications Quantum Jazzy 1420 Power Base Shroud Removed is similar Active-Trac Suspension Electronics TrayTo operate the manual freewheel lever Manual Freewheel LeverUnplug the connectors from the electronics tray Seat Height and Seat Angle AdjustmentO M F O R T a D J U S T M E N T S To change the seat height or seat angleSeatback Angle Adjustment To adjust the seatback angleArmrest WidthAdjustment ArmrestAngleAdjustment To change the armrest angleFootrest Angle To adjust the footrest angleController Position To extend the controllerTo adjust the ELR angle To adjust the SFR lengthTo adjust the ELR length Swing-away FootrestsAnti-Tip Wheels To adjust the anti-tip wheelsPower Elevating Seat Actuator Power Elevating Seat OptionTo operate the power elevating seat Power Elevating Seat OperationTo use the swivel feature To charge the batteries using the off-board charger TochargethebatteriesusingtheonboardchargerB a T T E R I E S a N D C H a R G I N G Batteries and ChargingFrequently Asked Questions FAQs How does the charger work? Battery Break-in TobreakinnewbatteriesformaximumefficiencyCan I use a different battery charger? How often must I charge the batteries?Why do my new batteries seem weak? Use these specifications to reorder deep-cycle batteriesHowcanIgetmaximumrangeordistancepercharge? What type of batteries should I use?How should I store my Power Chair and its batteries? HowcanIensuremaximumbatterylife?What about public transportation? What about shipping?Page I . O P E R a T I O N To select a speed setting Speed SettingsPower Accessories Power ModuleActuator Lighting Module Not Shown Sleep ModeTrouble Codes Other components are located inside the power base Motor wiring harnesses Battery wiring harnessesEuropa Master Remote JoystickTo enable the lockout system On/off key toggles the system power on and offOn/Off Key System Status LightDrive Mode and Actuator Display also Remote Status Display To change the drive mode programBattery Saver Feature Sleep Mode If EnabledFlash Code Sequence Diagnosis Solution Fault CodesShould your power chair come in contact with water Care and MaintenanceTemperature I I . C a R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes To calibrate the joystick Remote Plus onlyMonthly Checks Cleaning Precautions Tire/Wheel ReplacementYearly Checks StorageTo replace the batteries Battery ReplacementMotor Brushes Corrective MaintenanceTo inspect orreplace the motorbrushes O P T I O N a L a C C E S S O R I E S Optional AccessoriesA R R a N T Y Lifetime Limited WarrantyT E S Remote Plus Controller Europa ControllerFit and Finish Performance Inclusion of all Parts