Invacare Tracer EXIR manual Stability ALL Models, Section General Guidelines

Page 8

GENERAL GUIDELINES

SECTION 1

GENERAL GUIDELINES

Section 1 - General Guidelines includes the following:

Stability

Weight Limitation

Operating Information

Safety/Handling of Wheelchairs

Tire Pressure

 

Weight Training

 

STABILITY - ALL MODELS

WARNING

The size/position of the front casters, size/position of the rear wheels, use of anti-tipper model, as well as the user condition directly relate to the stability of the wheelchair. Any change to one (1) or any combination of the six (6) may cause the wheelchair to decrease in stability. These adjustments MUST be performed by a qualified technician.

 

Caster Size

Caster Position

Wheel Size

Wheel Position

Anti-Tippers

User Condition

 

 

 

 

 

 

 

Caster Size

 

 

 

 

 

 

 

Caster Position

 

 

 

 

 

 

 

Wheel Size

 

 

 

 

 

 

 

Wheel Position

 

 

 

 

 

 

 

User Condition

 

 

 

 

 

 

 

NOTE: When changes to the left hand column occur, follow across the chart and refer to the proce- dure that is checked () to maintain the proper stability, safety and handling of the wheelchair.

Seat-to-floor heights have specific positions depending on rear wheel size, rear wheel position, front caster size and front caster position. These adjustments MUST be performed by a qualified technician.

Anti-tippers are specific to the different seat-to-floor heights. Refer to the chart in INSTALLING/ADJUSTING THE ANTI-TIPPERS in SECTION 8 of this manual for correct usage and adjustment. If these requirements cannot be achieved, do not use the wheelchair. Contact a qualified technician.

If changing the seat-to-floor height the correct anti-tippers MUST be ordered to maintain a 1-1/2 to 2-inch ground clearance.

Anti-tippers MUST be fully engaged. Ensure that the release button of the anti-tipper fully protrudes out of the hole on the bottom of the wheelchair frame.

Ensure both anti-tippers are adjusted to the same height.

Anti-tippers MUST BE attached at all times. Inasmuch as the anti-tippers are an option on this wheelchair (you may order with or without the anti- tippers), Invacare strongly recommends ordering the anti-tippers as an additional safeguard for the wheelchair user.

Tracer® EXI

8

Part No. 1110547

Image 8
Contents Tracer R EXI Tracer EXI Table of Contents ANTI-TIPPERS/WHEEL Locks Special Notes Special NotesLocationslabel Label LocationsSpecifications SpecificationsSection General Guidelines Stability ALL ModelsGeneral Guidelines Operating Information General Guidelines SectionTire Pressure Weight TrainingWeight Limitation Coping with Everyday Obstacles SAFETY/HANDLING of WheelchairsStability and Balance Percentage of Weight Distribution Tipping Do not tip the wheelchair without assistanceMethod 2 Wheelchair Without Step Tube Method 1 Wheelchair with Step TubesTipping Curbs Method 2 Wheelchair Without Step Tube Stairways ESCALATORS? SorryTransferring to and from Other Seats Unfolding and Folding the WheelchairFolding Unfolding FoldingSection Safety Inspection Safety Inspection ChecklistSafety Inspection Troubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresSafety Inspection INSTALLING/REMOVING the Front Riggings Figure InstallingRemoving Front Riggings SectionFootplate Height Adjustment Spring Button Height Adjustment FigureBOLT-IN-PLACE Height Adjustment Figure RiggingsFixed Frame Figure Outside of Swingaway Front RiggingRAISING/LOWERING the Elevating Legrest Assembly Figure Heel Loop Replacement FigureInside Outside Swingaway Front Rigging Detail a Footplates with BOLT-IN-PLACESpring Buttons Footplates Removing and Installing Armrest Figure Installing ArmrestRemoving Armrest ArmsReplacing Back Upholstery Figure Replacing Seat Upholstery FigureSeat and Back Section Seat and BackAdjusting the Seat Width EXI with Swingaway Front Riggings FigureSeat Backand Section Seat and BackCrossbrace Hardware DetailDetail B Removing Upper Mounting Hardware EXI with Fixed Frame FigureDetail a Removing Lower Mounting Hardware REMOVING/INSTALLING the Rear Wheels Permanent Axles FigureRear Wheels Section Rear WheelsREPLACING/REPAIRING Rear Wheel TIRE/TUBE Replacing Rear Wheel Handrim FigureSection Rear Wheels WheelsrearINSTALLING/REPLACING Fork Assemblies Figure Adjusting Forks FigureFront Casters Section Front CastersREPLACING/REPAIRING Front Caster TIRE/TUBE Replacing Front Casters FigureCastersfront Section Front CastersINSTALLING/ADJUSTING the ANTI-TIPPERS Installing the ANTI-TIPPERS Figures 1ANTI-TIPPERS/WHEEL Locks Section ANTI-TIPPERS/WHEEL LocksAdjusting the ANTI-TIPPERS Figure Section ANTI-TIPPERS/WHEEL LocksLOCKSTIPPERS/WHEEL AntiAdjusting the Disk Wheel Locks Figure USING/ADJUSTING the Disk Wheel LocksUsing the Patient Operated Disk Wheel Locks Figure Installing Wheel Lock Shoe Extensions Figure LocksSEAT-TO-FLOOR Height Changing SEAT-TO-FLOOR Height FigureSEAT-TO-FLOOR Height Section Changing SEAT-TO-FLOOR Height Options Installing the Seat Positioning Strap FigureOptions Section Tracer EXI Warranty WarrantyMade in Mexico Canada