Invacare Tracer EXIR manual Locationslabel, Label Locations

Page 6

LOCATIONSLABEL

LABEL LOCATIONS

LABEL LOCATIONS

WARNING

Refer to Owner's Manual for proper anti-tipper

setting.1085379

IMPORTANT NOTICE

The wheel locks on this wheelchair have been pre-set at the factory to comply with the Veterans Administration functional Standard 8320.01 of the Federal Register, paragraph

3.2.4.5.3.If these wheel locks do not meet your needs, follow instructions below.

!CAUTION

Any wheel lock adjustments should embed wheel lock shoe at least 1/8" into tire when locked (3/16" on pneumatic tires).

INSTRUCTIONS FOR WHEEL

LOCK ADJUSTMENTS

1.Loosen wheel lock mounting fastener, which runs through mounting bracket and frame.

2.Slide clamp toward rear wheel until wheel lock shoe is embedded into tire material at least 1/8" when handle is engaged to the lock position (3/16" for pneumatic tires).

3.Tighten mounting fastener to secure mounting bracket in desired location and recheck lock shoe embedding.

4.Inspect for correct locking action BEFORE actual use.

00078X021-0394

 

WARNING

DO NOT OPERATE WITHOUT

 

THE ANTI-TIP TUBES

REV. 5/98

INSTALLED. P/N 60106X144

Crossmember

Lower Frame

Tube

Tracer® EXI

6

Part No. 1110547

Image 6
Contents Tracer R EXI Tracer EXI Table of Contents ANTI-TIPPERS/WHEEL Locks Special Notes Special NotesLocationslabel Label LocationsSpecifications SpecificationsStability ALL Models General GuidelinesSection General Guidelines Operating Information General Guidelines SectionWeight Training Weight LimitationTire Pressure SAFETY/HANDLING of Wheelchairs Stability and BalanceCoping with Everyday Obstacles Percentage of Weight Distribution Tipping Do not tip the wheelchair without assistanceMethod 1 Wheelchair with Step Tubes Tipping Curbs Method 2 Wheelchair Without Step TubeMethod 2 Wheelchair Without Step Tube Stairways ESCALATORS? SorryTransferring to and from Other Seats Unfolding and Folding the WheelchairFolding Unfolding FoldingSafety Inspection Checklist Safety InspectionSection Safety Inspection Maintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance ProceduresSafety Inspection Removing INSTALLING/REMOVING the Front Riggings FigureInstalling Front Riggings SectionBOLT-IN-PLACE Height Adjustment Figure Footplate Height AdjustmentSpring Button Height Adjustment Figure RiggingsFixed Frame Figure Outside of Swingaway Front RiggingRAISING/LOWERING the Elevating Legrest Assembly Figure Heel Loop Replacement FigureDetail a Footplates with BOLT-IN-PLACE Spring Buttons FootplatesInside Outside Swingaway Front Rigging Removing Armrest Removing and Installing Armrest FigureInstalling Armrest ArmsSeat and Back Section Replacing Back Upholstery FigureReplacing Seat Upholstery Figure Seat and BackSeat Backand Adjusting the Seat WidthEXI with Swingaway Front Riggings Figure Section Seat and BackDetail Detail BCrossbrace Hardware EXI with Fixed Frame Figure Detail a Removing Lower Mounting HardwareRemoving Upper Mounting Hardware Rear Wheels Section REMOVING/INSTALLING the Rear WheelsPermanent Axles Figure Rear WheelsSection Rear Wheels REPLACING/REPAIRING Rear Wheel TIRE/TUBEReplacing Rear Wheel Handrim Figure WheelsrearFront Casters Section INSTALLING/REPLACING Fork Assemblies FigureAdjusting Forks Figure Front CastersCastersfront REPLACING/REPAIRING Front Caster TIRE/TUBEReplacing Front Casters Figure Section Front CastersANTI-TIPPERS/WHEEL Locks Section INSTALLING/ADJUSTING the ANTI-TIPPERSInstalling the ANTI-TIPPERS Figures 1 ANTI-TIPPERS/WHEEL LocksLOCKSTIPPERS/WHEEL Adjusting the ANTI-TIPPERS FigureSection ANTI-TIPPERS/WHEEL Locks AntiUSING/ADJUSTING the Disk Wheel Locks Using the Patient Operated Disk Wheel Locks FigureAdjusting the Disk Wheel Locks Figure Installing Wheel Lock Shoe Extensions Figure LocksChanging SEAT-TO-FLOOR Height Figure SEAT-TO-FLOOR Height SectionSEAT-TO-FLOOR Height Changing SEAT-TO-FLOOR Height Installing the Seat Positioning Strap Figure Options SectionOptions Tracer EXI Warranty WarrantyMade in Mexico Canada