Invacare ProntoTM M6 manual Transporting the Wheelchair Figures 1, Disassembling The Wheelchair

Page 42

PROCEDURE 11

TRANSPORT

This Procedure Includes the Following:

Transporting the Wheelchair

T

WARNING

 

RAfterANYadjustments,repairorserviceandBE-

AFORE use, make sure that all attaching hard- ware is tightened securely - otherwise injury or

N

damage may result.

S

 

PFor the following procedures, make sure the

OON/OFF switch on the joystick is in the OFF position.

R

TTRANSPORTING THE WHEELCHAIR (FIGURES 1 AND 2)

Disassembling The Wheelchair

NOTE: To reassemble the wheelchair, reverse the following steps.

1.Disconnect the joystick. Refer to DISCON-

NECTING/CONNECTING THE MKIV JOY- STICK in PROCEDURE 9 of the manual.

2.Fold down the back. Refer to FOLDING/UN- FOLDING THE BACK in PROCEDURE 5 of the manual.

3.Remove the seat. Refer to REMOVING/IN- STALLING THE SEAT in PROCEDURE 4 of the manual.

4.Remove the shroud. Refer to REMOVING/ INSTALLING THE SHROUD in PROCE- DURE 7 of the manual.

NOTE: The motor connectors are located UN- DERNEATH the FRONT frame assembly.

WARNING

When reconnecting the motors, be sure the motor wires are routed toward the INSIDE of the wheelchair frame - otherwise, injury or damage may result.

5.Disconnect the LEFT motor connector from the controller connector.

6.Repeat STEP 5 for the RIGHT motor connector.

STEP 5 AND 6 Controller

STEP 7

Connector Battery

Controller

Connector

Connector STEP 8

Left Motor

Circuit Breaker

 

Connector

 

Left Motor Wire

Routed (Toward

Inside Of Frame)

Wheelchair Frame

Front Frame

 

Assembly

 

STEP 9 AND 10

Red

Black

Retaining

Cable

Cable

Pin

 

 

Rear

Frame

Assembly

 

DETAIL "A"

Retaining

Bend

Pin Lock

Lock

 

Out

FIGURE 1 - TRANSPORTING THE WHEELCHAIR

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents ProntoTM M6 R N I N G Wheelchair TIE-DOWN Restraints and Seat Positioning StrapsTable of Contents Specifications PerformanceGeneral Guidelines ProcedureRepair or SERVICE/CONTROLLER Settings Operating InformationProcedure General GuidelinesWeight Training WeightlimitationElectromagnetic Interference EMI from Radio Wave Sources Important Information SAFETY/HANDLING WheelchairsPowered Wheelchair Electromagnetic Interference EMI Stability and BalanceCoping With Everyday Obstacles StairwaysTransferring to and From Other Seats Reaching, Leaning, Bending and Bending Forward Reaching, Bending BackwardOtherwise injury or damage may result Safety Inspection Checklist Troubleshooting Guide Safety INSPECTION/TROUBLESHOOTINGPROCEDUREWheelchair Operation H P E E E R L a C T H I a O I NWheelchair Operation Using The Joystick To Drive The ChairSwitch Speed Control Knob Joystick To Move Forward Left To Move Right BackwardM S Armrest Angle Adjustment FigureArmrest Width Adjustment Figure ArmsArms Armrest Depth Adjustment FigureArmrest Height Adjustment Figure Mounting Screw Stability Armpost Set ScrewsREMOVING/INSTALLING Seat Support Collars Figure Seat Assembly Support Post Mounting Wheelchair FrameMounting Hole Seat Support NutCollar Bolt Determined Post Seat Procedure REMOVING/INSTALLINGSeat Assembly A TSeat Assemblies with Seat Support Collars Figure Welded Bend End of Lock CollarAdjusting the Seat Height SeatSeat Assemblies Without The Seat Support Collars Figure Retaining Pin Bend End Lock HeightHoles Seat Mounting SupportMiddle Position Adjusting the Seat Support Posts FigureHighest Position Lowest PositionAdjusting the Seat Depth Seat AssemblyMounting Holes Seat Pan Washer Self-Locking Washer Bolts REMOVING/INSTALLING the Seat Positioning Strap Figure InstallingFOLDING/UNFOLDING Back Figure Adjusting the Back Angle FigureAdjusting the Headrest Figure BackWheelchair Frame Footboard Assembly Footboard AssemblyAdjusting O T B O a R D S E M B L YAdjusting the Footboard Assembly Angle Figure Procedure Footboard AssemblyENGAGING/DISENGAGING Motor Locks Figure REMOVING/INSTALLING the Shroud FigureReplacing the Foam Filled Tires Onto the Wheel RIM SHROUD/WHEELSSHROUD/WHEELS Rear of WheelchairReplacing the FRONT/REAR REMOVING/INSTALLING the AxleCap Nut Mounting Hole Wheelchair Frame Caster Assembly Shroud Covers FigureBatteries Without Removing Cables Figure Disconnect Front Battery From Rear BatteryRetaining Ring Rear Frame Assembly BatteriesBatteries CONNECTING/DISCONNECTING Battery Cables FigureConnecting T T E R I E STerminal Cap Front U1 Battery Rear U1 Battery CONNECTING/DISCONNECTING Circuit Breaker Cables FigureBlack Battery FlangeReplacing Batteries Recommended Battery TypesCleaning Battery Terminals T TChargingbatteries Charger Port Cover AC Power Cord To 110-Volt Wall Outlet Charging Using The On-Board Battery Charger FigureCharging LED Indicator Light Front WheelchairBattery Charger Operation On-Board Battery Charger FigureREMOVING/INSTALLING on Board Battery Charger Independent Battery ChargerMkiv Joystick in Frontal Position Retracting the Mkiv Joystick FigureElectronics Mkiv Joystick Parallel to ArmrestRepositioning the Mkiv Joystick DISCONNECTING/CONNECTING the Mkiv Joystick FigureDisconnecting ElectronicsTransporting the Wheelchair Figures 1 TransportDisassembling The Wheelchair Step TransportA N S P O R T Disassembled ViewProcedure Options REMOVING/INSTALLING the CRUTCH/CANE Holder FigureREMOVING/INSTALLING the Safety Flag Figure T I O N ST E S Page Limited Warranty R R a N T YUSA

ProntoTM M6 specifications

The Invacare ProntoTM M6 is a highly regarded power wheelchair designed to enhance mobility and independence for users with varying needs. Known for its compact design, the ProntoTM M6 combines performance, comfort, and advanced technology to meet the demands of everyday living.

One of the standout features of the ProntoTM M6 is its innovative mid-wheel drive system, which provides exceptional maneuverability in tight spaces. The compact footprint allows users to navigate through indoor environments with ease, making it suitable for home use and various public spaces. With a turning radius of just 20.5 inches, it can easily negotiate doorways and hallways, allowing users to maintain their independence.

The ProntoTM M6 is equipped with advanced suspension technology that enhances stability and comfort while traversing different terrains. This feature absorbs shocks and minimizes vibrations, providing a smoother ride, whether on indoor flooring or outdoor surfaces. The overall design ensures that users experience minimal fatigue and discomfort during daily activities.

An important aspect of the ProntoTM M6 is its thoughtful ergonomic design. The adjustable seating system offers various positioning options, allowing users to customize their seating arrangement for optimal comfort. This includes adjustable armrests, footrests, and backrests, which can accommodate a wide range of user preferences and physical requirements.

Safety is a priority with the ProntoTM M6, featuring a variety of safety enhancements. The wheelchair includes anti-tippers and a reliable braking system that ensures stability and security while in motion. The intuitive joystick control allows users to operate the chair effortlessly, granting precise control over speed and direction.

Battery longevity and efficiency are also key characteristics of the ProntoTM M6. It can travel significant distances on a single charge, allowing users to enjoy extended outings without the worry of battery depletion. The wheelchair is designed for easy access to the battery compartment, making maintenance a hassle-free process.

In conclusion, the Invacare ProntoTM M6 power wheelchair stands out for its exceptional mobility, comfort, and safety features. It is perfect for those seeking independence and a reliable means of transportation. With its advanced technologies and user-friendly design, the ProntoTM M6 empowers individuals to navigate their environments confidently and comfortably.
Top Page Image Contents