Invacare ProntoTM M6 Replacing the FRONT/REAR, Shroud Covers Figure, REMOVING/INSTALLING the Axle

Page 31

SHROUD/WHEELS

PROCEDURE 8

REMOVING/INSTALLING THE AXLE

REPLACING THE FRONT/REAR

SHROUD COVERS (FIGURE 3)

CASTER ASSEMBLIES (FIGURE 4)

S

NOTE: The front and rear axle shroud covers are removed/installed in the same manner.

NOTE: To install the front and rear axle shroud covers, reverse the following steps.

Removing

1.If necessary, remove the shroud. Refer to REMOVING/INSTALLING THE SHROUD in PROCEDURE 7 of the manual.

2.Remove the mounting screw securing the axle shroud cover to the wheelchair frame.

3.Remove the axle shroud cover from the wheel- chair frame.

Mounting Screw

Front

Axle

Shroud

Cover

Wheelchair

Frame

Caster

Assembly

NOTE: Rear axle shroud cover NOT shown.

FIGURE 3 - REMOVING/INSTALLING THE FORK

AND STEM COVERS

NOTE: Front and rear caster assemblies are re- placed in the same manner.

NOTE: When replacing the front/rear caster as- semblies, it is necessary to brace the caster as- semblies to prevent the wheel from spinning.

1.Remove the fork or stem cover from the wheel- chair frame. Refer to REMOVING/INSTALL- ING THE FORK AND STEM COVERS in this procedure of the manual.

2.Hold the caster assembly with one (1) hand and loosen the cap nut with the other hand using a crescent wrench.

3.Remove the EXISTING cap nut securing the EX- ISTING caster assembly to the wheelchair frame.

4.Remove the EXISTING caster assembly from the wheelchair frame.

5.Position the NEW caster assembly in the mounting hole in the wheelchair frame.

6.Secure the NEW caster assembly to the wheelchair frame with the NEW cap nut. Se- curely tighten.

7.If necessary, repeat STEPS 1-4 for the re- maining three (3) caster assemblies.

Cap Nut

Mounting

Hole

Wheelchair

Frame

Caster

Assembly

H R O U D

/

W

H

E

E

L

S

FIGURE 4 - REPLACING THE FRONT/REAR

CASTER ASSEMBLIES

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents ProntoTM M6 Wheelchair TIE-DOWN Restraints and Seat Positioning Straps R N I N GTable of Contents Performance SpecificationsOperating Information ProcedureRepair or SERVICE/CONTROLLER Settings General GuidelinesGeneral Guidelines ProcedureWeightlimitation Weight TrainingElectromagnetic Interference EMI from Radio Wave Sources Stability and Balance SAFETY/HANDLING WheelchairsPowered Wheelchair Electromagnetic Interference EMI Important InformationStairways Coping With Everyday ObstaclesTransferring to and From Other Seats Reaching, Bending Backward Reaching, Leaning, Bending and Bending ForwardOtherwise injury or damage may result Safety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGPROCEDURE Troubleshooting GuideH P E E E R L a C T H I a O I N Wheelchair OperationTo Move Forward Left To Move Right Backward Using The Joystick To Drive The ChairSwitch Speed Control Knob Joystick Wheelchair OperationArms Armrest Angle Adjustment FigureArmrest Width Adjustment Figure M SMounting Screw Stability Armpost Set Screws Armrest Depth Adjustment FigureArmrest Height Adjustment Figure ArmsSeat Assembly Support Post Mounting Wheelchair Frame REMOVING/INSTALLING Seat Support Collars FigureMounting Hole Seat Support NutCollar Bolt Determined Post A T REMOVING/INSTALLINGSeat Assembly Seat ProcedureWelded Bend End of Lock Collar Seat Assemblies with Seat Support Collars FigureSeat Adjusting the Seat HeightSeat Assemblies Without The Seat Support Collars Figure Seat Mounting Support HeightHoles Retaining Pin Bend End LockLowest Position Adjusting the Seat Support Posts FigureHighest Position Middle PositionSeat Assembly Adjusting the Seat DepthMounting Holes Seat Pan Washer Self-Locking Washer Bolts Installing REMOVING/INSTALLING the Seat Positioning Strap FigureBack Adjusting the Back Angle FigureAdjusting the Headrest Figure FOLDING/UNFOLDING Back FigureO T B O a R D S E M B L Y Footboard AssemblyAdjusting Wheelchair Frame Footboard AssemblyProcedure Footboard Assembly Adjusting the Footboard Assembly Angle FigureSHROUD/WHEELS REMOVING/INSTALLING the Shroud FigureReplacing the Foam Filled Tires Onto the Wheel RIM ENGAGING/DISENGAGING Motor Locks FigureRear of Wheelchair SHROUD/WHEELSShroud Covers Figure REMOVING/INSTALLING the AxleCap Nut Mounting Hole Wheelchair Frame Caster Assembly Replacing the FRONT/REARBatteries Disconnect Front Battery From Rear BatteryRetaining Ring Rear Frame Assembly Batteries Without Removing Cables FigureT T E R I E S CONNECTING/DISCONNECTING Battery Cables FigureConnecting BatteriesFlange CONNECTING/DISCONNECTING Circuit Breaker Cables FigureBlack Battery Terminal Cap Front U1 Battery Rear U1 BatteryT T Recommended Battery TypesCleaning Battery Terminals Replacing BatteriesChargingbatteries Front Wheelchair Charging Using The On-Board Battery Charger FigureCharging LED Indicator Light Charger Port Cover AC Power Cord To 110-Volt Wall OutletOn-Board Battery Charger Figure Battery Charger OperationIndependent Battery Charger REMOVING/INSTALLING on Board Battery ChargerMkiv Joystick Parallel to Armrest Retracting the Mkiv Joystick FigureElectronics Mkiv Joystick in Frontal PositionElectronics DISCONNECTING/CONNECTING the Mkiv Joystick FigureDisconnecting Repositioning the Mkiv JoystickTransport Transporting the Wheelchair Figures 1Disassembling The Wheelchair Disassembled View TransportA N S P O R T StepT I O N S REMOVING/INSTALLING the CRUTCH/CANE Holder FigureREMOVING/INSTALLING the Safety Flag Figure Procedure OptionsT E S Page R R a N T Y Limited WarrantyUSA

ProntoTM M6 specifications

The Invacare ProntoTM M6 is a highly regarded power wheelchair designed to enhance mobility and independence for users with varying needs. Known for its compact design, the ProntoTM M6 combines performance, comfort, and advanced technology to meet the demands of everyday living.

One of the standout features of the ProntoTM M6 is its innovative mid-wheel drive system, which provides exceptional maneuverability in tight spaces. The compact footprint allows users to navigate through indoor environments with ease, making it suitable for home use and various public spaces. With a turning radius of just 20.5 inches, it can easily negotiate doorways and hallways, allowing users to maintain their independence.

The ProntoTM M6 is equipped with advanced suspension technology that enhances stability and comfort while traversing different terrains. This feature absorbs shocks and minimizes vibrations, providing a smoother ride, whether on indoor flooring or outdoor surfaces. The overall design ensures that users experience minimal fatigue and discomfort during daily activities.

An important aspect of the ProntoTM M6 is its thoughtful ergonomic design. The adjustable seating system offers various positioning options, allowing users to customize their seating arrangement for optimal comfort. This includes adjustable armrests, footrests, and backrests, which can accommodate a wide range of user preferences and physical requirements.

Safety is a priority with the ProntoTM M6, featuring a variety of safety enhancements. The wheelchair includes anti-tippers and a reliable braking system that ensures stability and security while in motion. The intuitive joystick control allows users to operate the chair effortlessly, granting precise control over speed and direction.

Battery longevity and efficiency are also key characteristics of the ProntoTM M6. It can travel significant distances on a single charge, allowing users to enjoy extended outings without the worry of battery depletion. The wheelchair is designed for easy access to the battery compartment, making maintenance a hassle-free process.

In conclusion, the Invacare ProntoTM M6 power wheelchair stands out for its exceptional mobility, comfort, and safety features. It is perfect for those seeking independence and a reliable means of transportation. With its advanced technologies and user-friendly design, the ProntoTM M6 empowers individuals to navigate their environments confidently and comfortably.
Top Page Image Contents