Invacare ProntoTM M6 manual Wheelchair Operation, H P E E E R L a C T H I a O I N

Page 14

PROCEDURE 3

WHEELCHAIR OPERATION

WO H P E E E R L A C T H I A O I N

R

This Procedure Includes the Following:

Wheelchair Operation

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.

WHEELCHAIR OPERATION

Switches/Indicators (Figure 1)

The following switches and indicators are located on the joystick housing:

ON/OFF SWITCH - The on/off switch is located on the BACK of the joystick housing. This two (2) posi- tion toggle switch is used for turning the wheelchair ON and OFF (DETAIL "B").

SPEED CONTROL KNOB - The speed control knob is located on the BACK of the joystick housing. This rotary knob is used for controlling the maximum speed of the wheelchair. Turning the knob clock- wise INCREASES the maximum speed of the wheel- chair. Turning the knob counter-clockwise DE- CREASES the maximum speed of the wheelchair (DETAIL "B").

BATTERY DISCHARGE INDICATOR (BDI) - The battery discharge indicator is located at the FRONT of the joystick housing. It provides information on the remaining charge in the batteries. At full charge the BDI will be Green. As the battery becomes dis- charged, the BDI will become Yellow (Amber), then Red and finally the BDI will flash ON and OFF Red. At this level, the user should charge the batteries as soon as possible (DETAIL "C").

The BDI will flash ON and OFF Yellow to indicate a reduced speed or power output.

The BDI also serves as a system diagnostic device when a fault is detected by the control module. A specific number of Green flashes will indicate the type of fault detected. For more information on us- ing the battery discharge indicator as a system diag- nostic device, contact a qualified technician.

NOTE: When reading the Battery Discharge Indica- tor (BDI), the joystick MUST be in the NEUTRAL position for an accurate reading.

MULTI FUNCTION CHARGER PORT- The multi function charger port is located at the front of the joystick housing. It provides access for charging the wheelchair batteries using an INDEPENDENT bat- tery charger, refer to CHARGING BATTERIES in PROCEDURE 8 of this manual. This port also serves as the Remote Programmer/AVS communication connection and is used for setting-up/programming the electronic control unit (DETAIL "A").

WARNING

Set-up/programming of the Electronic Con- trol Unit is to be performed ONLY by a quali- fied technician. The fine tuning adjustments of the controller may affect other activities of the wheelchair. Damage to the equipment could occur under these circumstances. If unqulaified individuals perform any work on these units, the warranty is voided.

DETAIL "A" - FRONT VIEW

Multi-

Function

Charger

Port

DETAIL "B" - REAR VIEW

Speed

On Switch

Position

Control

 

Knob

Off Switch

 

 

Position

DETAIL "C"

Horn

Battery

Discharge

Indicator

To Controller

FIGURE 1 - WHEELCHAIR OPERATION -

SWITCHES/INDICATORS

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents ProntoTM M6 R N I N G Wheelchair TIE-DOWN Restraints and Seat Positioning StrapsTable of Contents Specifications PerformanceGeneral Guidelines ProcedureRepair or SERVICE/CONTROLLER Settings Operating InformationProcedure General GuidelinesElectromagnetic Interference EMI from Radio Wave Sources Weight TrainingWeightlimitation Important Information SAFETY/HANDLING WheelchairsPowered Wheelchair Electromagnetic Interference EMI Stability and BalanceTransferring to and From Other Seats Coping With Everyday ObstaclesStairways Reaching, Leaning, Bending and Bending Forward Reaching, Bending BackwardOtherwise injury or damage may result Safety Inspection Checklist Troubleshooting Guide Safety INSPECTION/TROUBLESHOOTINGPROCEDUREWheelchair Operation H P E E E R L a C T H I a O I NWheelchair Operation Using The Joystick To Drive The ChairSwitch Speed Control Knob Joystick To Move Forward Left To Move Right BackwardM S Armrest Angle Adjustment FigureArmrest Width Adjustment Figure ArmsArms Armrest Depth Adjustment FigureArmrest Height Adjustment Figure Mounting Screw Stability Armpost Set ScrewsMounting Hole Seat Support NutCollar Bolt Determined Post REMOVING/INSTALLING Seat Support Collars FigureSeat Assembly Support Post Mounting Wheelchair Frame Seat Procedure REMOVING/INSTALLINGSeat Assembly A TSeat Assemblies with Seat Support Collars Figure Welded Bend End of Lock CollarSeat Assemblies Without The Seat Support Collars Figure Adjusting the Seat HeightSeat Retaining Pin Bend End Lock HeightHoles Seat Mounting SupportMiddle Position Adjusting the Seat Support Posts FigureHighest Position Lowest PositionMounting Holes Seat Pan Washer Self-Locking Washer Bolts Adjusting the Seat DepthSeat Assembly REMOVING/INSTALLING the Seat Positioning Strap Figure InstallingFOLDING/UNFOLDING Back Figure Adjusting the Back Angle FigureAdjusting the Headrest Figure BackWheelchair Frame Footboard Assembly Footboard AssemblyAdjusting O T B O a R D S E M B L YAdjusting the Footboard Assembly Angle Figure Procedure Footboard AssemblyENGAGING/DISENGAGING Motor Locks Figure REMOVING/INSTALLING the Shroud FigureReplacing the Foam Filled Tires Onto the Wheel RIM SHROUD/WHEELSSHROUD/WHEELS Rear of WheelchairReplacing the FRONT/REAR REMOVING/INSTALLING the AxleCap Nut Mounting Hole Wheelchair Frame Caster Assembly Shroud Covers FigureBatteries Without Removing Cables Figure Disconnect Front Battery From Rear BatteryRetaining Ring Rear Frame Assembly BatteriesBatteries CONNECTING/DISCONNECTING Battery Cables FigureConnecting T T E R I E STerminal Cap Front U1 Battery Rear U1 Battery CONNECTING/DISCONNECTING Circuit Breaker Cables FigureBlack Battery FlangeReplacing Batteries Recommended Battery TypesCleaning Battery Terminals T TChargingbatteries Charger Port Cover AC Power Cord To 110-Volt Wall Outlet Charging Using The On-Board Battery Charger FigureCharging LED Indicator Light Front WheelchairBattery Charger Operation On-Board Battery Charger FigureREMOVING/INSTALLING on Board Battery Charger Independent Battery ChargerMkiv Joystick in Frontal Position Retracting the Mkiv Joystick FigureElectronics Mkiv Joystick Parallel to ArmrestRepositioning the Mkiv Joystick DISCONNECTING/CONNECTING the Mkiv Joystick FigureDisconnecting ElectronicsDisassembling The Wheelchair Transporting the Wheelchair Figures 1Transport Step TransportA N S P O R T Disassembled ViewProcedure Options REMOVING/INSTALLING the CRUTCH/CANE Holder FigureREMOVING/INSTALLING the Safety Flag Figure T I O N ST E S Page Limited Warranty R R a N T YUSA

ProntoTM M6 specifications

The Invacare ProntoTM M6 is a highly regarded power wheelchair designed to enhance mobility and independence for users with varying needs. Known for its compact design, the ProntoTM M6 combines performance, comfort, and advanced technology to meet the demands of everyday living.

One of the standout features of the ProntoTM M6 is its innovative mid-wheel drive system, which provides exceptional maneuverability in tight spaces. The compact footprint allows users to navigate through indoor environments with ease, making it suitable for home use and various public spaces. With a turning radius of just 20.5 inches, it can easily negotiate doorways and hallways, allowing users to maintain their independence.

The ProntoTM M6 is equipped with advanced suspension technology that enhances stability and comfort while traversing different terrains. This feature absorbs shocks and minimizes vibrations, providing a smoother ride, whether on indoor flooring or outdoor surfaces. The overall design ensures that users experience minimal fatigue and discomfort during daily activities.

An important aspect of the ProntoTM M6 is its thoughtful ergonomic design. The adjustable seating system offers various positioning options, allowing users to customize their seating arrangement for optimal comfort. This includes adjustable armrests, footrests, and backrests, which can accommodate a wide range of user preferences and physical requirements.

Safety is a priority with the ProntoTM M6, featuring a variety of safety enhancements. The wheelchair includes anti-tippers and a reliable braking system that ensures stability and security while in motion. The intuitive joystick control allows users to operate the chair effortlessly, granting precise control over speed and direction.

Battery longevity and efficiency are also key characteristics of the ProntoTM M6. It can travel significant distances on a single charge, allowing users to enjoy extended outings without the worry of battery depletion. The wheelchair is designed for easy access to the battery compartment, making maintenance a hassle-free process.

In conclusion, the Invacare ProntoTM M6 power wheelchair stands out for its exceptional mobility, comfort, and safety features. It is perfect for those seeking independence and a reliable means of transportation. With its advanced technologies and user-friendly design, the ProntoTM M6 empowers individuals to navigate their environments confidently and comfortably.
Top Page Image Contents