Invacare ProntoTM M6 Adjusting the Seat Support Posts Figure, Highest Position, Middle Position

Page 23

SEAT

PROCEDURE 5

HIGHEST POSITION

Nut

Mounting

Hole

Bolt

Middle

Mounting Seat Support

HoleCollar

ADJUSTING THE SEAT SUPPORT POSTS (FIGURE 6)

NOTE: If the retaining pin will NOT pass through the seat mounting support AND through one (1) of the three (3) height mounting holes in the seat support post, perform the following steps:

1.Loosen, but DO NOT remove, the hex bolt securing the seat support post to the seat stand.

2.Grasp the seat support post and rotate it until the height adjustment holes align with the holes in the seat mounting support.

S E A T

Seat Support Post

MIDDLE POSITION

NutMounting Hole

Top Mount-

Bolt

ing Hole

 

Seat Support

Collar

Seat Support Post

LOWEST POSITION

Welded

Collar

3.Keeping the holes aligned, tighten the hex bolt securing the seat support post to the seat stand.

4.If necessary, repeat STEPS 1-3 for the re- maining seat support posts.

 

Hex Bolt

 

Seat Stand

Seat

Height Adjustment

Holes

Support

 

Post

Rotate to

 

 

Align Holes

FIGURE 6 - ADJUSTING THE SEAT SUPPORT POSTS

No Seat Support

Collar Required

FIGURE 5 - ADJUSTING THE SEAT HEIGHT - SEAT ASSEMBLIES WITH SEAT SUPPORT COLLARS

23

Image 23
Contents ProntoTM M6 Wheelchair TIE-DOWN Restraints and Seat Positioning Straps R N I N GTable of Contents Performance SpecificationsOperating Information ProcedureRepair or SERVICE/CONTROLLER Settings General GuidelinesGeneral Guidelines ProcedureElectromagnetic Interference EMI from Radio Wave Sources Weight TrainingWeightlimitation Stability and Balance SAFETY/HANDLING WheelchairsPowered Wheelchair Electromagnetic Interference EMI Important InformationTransferring to and From Other Seats Coping With Everyday ObstaclesStairways Reaching, Bending Backward Reaching, Leaning, Bending and Bending ForwardOtherwise injury or damage may result Safety Inspection Checklist Safety INSPECTION/TROUBLESHOOTINGPROCEDURE Troubleshooting GuideH P E E E R L a C T H I a O I N Wheelchair OperationTo Move Forward Left To Move Right Backward Using The Joystick To Drive The ChairSwitch Speed Control Knob Joystick Wheelchair OperationArms Armrest Angle Adjustment FigureArmrest Width Adjustment Figure M SMounting Screw Stability Armpost Set Screws Armrest Depth Adjustment FigureArmrest Height Adjustment Figure ArmsMounting Hole Seat Support NutCollar Bolt Determined Post REMOVING/INSTALLING Seat Support Collars FigureSeat Assembly Support Post Mounting Wheelchair Frame A T REMOVING/INSTALLINGSeat Assembly Seat ProcedureWelded Bend End of Lock Collar Seat Assemblies with Seat Support Collars FigureSeat Assemblies Without The Seat Support Collars Figure Adjusting the Seat HeightSeat Seat Mounting Support HeightHoles Retaining Pin Bend End LockLowest Position Adjusting the Seat Support Posts FigureHighest Position Middle PositionMounting Holes Seat Pan Washer Self-Locking Washer Bolts Adjusting the Seat DepthSeat Assembly Installing REMOVING/INSTALLING the Seat Positioning Strap FigureBack Adjusting the Back Angle FigureAdjusting the Headrest Figure FOLDING/UNFOLDING Back FigureO T B O a R D S E M B L Y Footboard AssemblyAdjusting Wheelchair Frame Footboard AssemblyProcedure Footboard Assembly Adjusting the Footboard Assembly Angle FigureSHROUD/WHEELS REMOVING/INSTALLING the Shroud FigureReplacing the Foam Filled Tires Onto the Wheel RIM ENGAGING/DISENGAGING Motor Locks FigureRear of Wheelchair SHROUD/WHEELSShroud Covers Figure REMOVING/INSTALLING the AxleCap Nut Mounting Hole Wheelchair Frame Caster Assembly Replacing the FRONT/REARBatteries Disconnect Front Battery From Rear BatteryRetaining Ring Rear Frame Assembly Batteries Without Removing Cables FigureT T E R I E S CONNECTING/DISCONNECTING Battery Cables FigureConnecting BatteriesFlange CONNECTING/DISCONNECTING Circuit Breaker Cables FigureBlack Battery Terminal Cap Front U1 Battery Rear U1 BatteryT T Recommended Battery TypesCleaning Battery Terminals Replacing BatteriesChargingbatteries Front Wheelchair Charging Using The On-Board Battery Charger FigureCharging LED Indicator Light Charger Port Cover AC Power Cord To 110-Volt Wall OutletOn-Board Battery Charger Figure Battery Charger OperationIndependent Battery Charger REMOVING/INSTALLING on Board Battery ChargerMkiv Joystick Parallel to Armrest Retracting the Mkiv Joystick FigureElectronics Mkiv Joystick in Frontal PositionElectronics DISCONNECTING/CONNECTING the Mkiv Joystick FigureDisconnecting Repositioning the Mkiv JoystickDisassembling The Wheelchair Transporting the Wheelchair Figures 1Transport Disassembled View TransportA N S P O R T StepT I O N S REMOVING/INSTALLING the CRUTCH/CANE Holder FigureREMOVING/INSTALLING the Safety Flag Figure Procedure OptionsT E S Page R R a N T Y Limited WarrantyUSA

ProntoTM M6 specifications

The Invacare ProntoTM M6 is a highly regarded power wheelchair designed to enhance mobility and independence for users with varying needs. Known for its compact design, the ProntoTM M6 combines performance, comfort, and advanced technology to meet the demands of everyday living.

One of the standout features of the ProntoTM M6 is its innovative mid-wheel drive system, which provides exceptional maneuverability in tight spaces. The compact footprint allows users to navigate through indoor environments with ease, making it suitable for home use and various public spaces. With a turning radius of just 20.5 inches, it can easily negotiate doorways and hallways, allowing users to maintain their independence.

The ProntoTM M6 is equipped with advanced suspension technology that enhances stability and comfort while traversing different terrains. This feature absorbs shocks and minimizes vibrations, providing a smoother ride, whether on indoor flooring or outdoor surfaces. The overall design ensures that users experience minimal fatigue and discomfort during daily activities.

An important aspect of the ProntoTM M6 is its thoughtful ergonomic design. The adjustable seating system offers various positioning options, allowing users to customize their seating arrangement for optimal comfort. This includes adjustable armrests, footrests, and backrests, which can accommodate a wide range of user preferences and physical requirements.

Safety is a priority with the ProntoTM M6, featuring a variety of safety enhancements. The wheelchair includes anti-tippers and a reliable braking system that ensures stability and security while in motion. The intuitive joystick control allows users to operate the chair effortlessly, granting precise control over speed and direction.

Battery longevity and efficiency are also key characteristics of the ProntoTM M6. It can travel significant distances on a single charge, allowing users to enjoy extended outings without the worry of battery depletion. The wheelchair is designed for easy access to the battery compartment, making maintenance a hassle-free process.

In conclusion, the Invacare ProntoTM M6 power wheelchair stands out for its exceptional mobility, comfort, and safety features. It is perfect for those seeking independence and a reliable means of transportation. With its advanced technologies and user-friendly design, the ProntoTM M6 empowers individuals to navigate their environments confidently and comfortably.