Invacare Pronto M91 Base manual Battery Charger Operation, On-Board Battery Charger

Page 64

SECTION 9—BATTERIES

Battery Charger Operation

WARNING

READ and CAREFULLY follow the manufacturer’s instructions for each charger (supplied or purchased). If charging instructions are not supplied, consult a qualified technician for proper procedures prior to use.

If the circuit breaker trips repeatedly, IMMEDIATELY unplug charger and contact dealer or a qualified technician.

Three prong to two prong adapters should not be used. Using three prong adapters can result in improper grounding and present a shock hazard to user.

On-Board Battery Charger

WARNING

Use of improper extension cord could result in risk of fire and electric shock.

When using an extension cord, use only a three wire extension cord having at least 16 AWG (American Wire Gauge) wire and the same or higher electrical rating as the device being connected.

Ensure the pins of the extension cord plug are the same number, size, and shape as those on the charger.

DO NOT under any circumstances cut or remove the round grounding plug from the charger AC cable plug or the extension cord plug.

NOTE: For this procedure, refer to FIGURE 9.6 on page 65.

NOTE: Charge indicator light is only visible with rear shroud removed.

1.Plug the female connector of the AC power cord (supplied) to the AC receptacle on the charger and plug in the male connector on the AC power cord into the wall outlet.

2.The On/Off LED indicator illuminates solid RED indicating that the charger is On.

3.If the On/Off LED indicator is “Blinking” RED, this is abnormal. Unplug AC power cord from the on‐board battery charger and wall outlet. Contact Invacare at the number listed on the back page of this manual.

4.When the On/Off LED indicator light is Off, charger is Off.

5.When the Charge LED indicator light is YELLOW, the batteries are charging.

6.When the Charge LED indicator light is solid GREEN, the batteries are fully charged (as their condition will allow). At this point, the charger automatically stops charging.

7.When charging is complete, unplug the male connector of the AC power cord from the wall outlet and then unplug the female connector of the AC power cord from the AC receptacle on the charger.

Pronto® M91™Base with SureStep®

64

Part No 1143153

Image 64
Contents Pronto M91Base With SureStep Reference Documents Reference DocumentsManual Table of Contents Table of Contents Wheelchair OperationSeat Register Your Product Transport Ready PackageSpecial Notes Special NotesMeaning Special Notes M91 Standard Label LocationsLabel Locations M91 Heavy Duty Wheelchairs With Trro Wheelchairs Without Trro Typical Product Parameters Pronto M91Typical Product Parameters InchController Settings/Repair or Service Accessories InformationGeneral Guidelines Operation InformationGeneral Guidelines Batteries Grounding Instructions Charging BatteriesWeight Training Weight LimitationModel Weight Limitation Rain TestEMI Information EMI InformationEMI Information SAFETY/HANDLING of Wheelchairs SAFETY/HANDLING of WheelchairsStability and Balance Coping With Everyday Obstacles Coping With Everyday ObstaclesPinch Points Pinch PointsLifting/Stairways Lifting/Stairways Hand Hold SupportsTransferring To and From Other Seats Transferring To and From Other SeatsReaching, Leaning and Bending Forward Reaching and Bending BackwardSafety INSPECTION/ Troubleshooting Safety Inspection ChecklistsInspect/Adjust Initially Safety INSPECTION/TROUBLESHOOTINGInspect/Adjust Monthly Inspect/Adjust WeeklyInspect/Adjust Periodically Troubleshooting Mechanical Troubleshooting ElectricalSolutions SPJ+, SPJ+ w/PSS or SPJ+ w/ACC JoysticksPossible Solution Display Description DefinitionSymptom Probable Cause Solutions MPJ+, PSR+, PSF+ Joysticks or DisplaysChecking Battery Charge Level DON’TTurning the Power On/Off Wheelchair OperationOperating the Wheelchair Wheelchair OperationUsing the Joystick to Drive the Wheelchair Movement ActionOn/Off Button SpeedometerService Indicator Speed Control ButtonsJoystick Charger/Programming InputInformation Gauge Display Drive Select Toggle Switch MPJ+ Joystick Switches and IndicatorsSpeed Control LCD Display Screens Splash ScreenLCD Display Driving Screen Remote On/Off Switch Programmable Mono Port 1/2 or External Mode SwitchWheelchair Operation Icon Description Preparing the Joystick for Use Mode SwitchMemory Card Slot Repositioning the Joystick Adjustable Asba SeatVan Seat SPJ+ Joysticks Disconnecting Disconnecting/Connecting the JoysticksConnecting Disconnecting MPJ+ JoysticksRemoving/Installing the Seat Assembly SeatRemoving SeatTilting the Seat Assembly InstallingTilting the Seat Assembly Back Tilting the Seat Assembly ForwardRemoving/Installing the Footboard Assembly Footboard AssemblyFootboard Assembly Adjusting the Footboard Assembly AngleAdjusting the Footboard Assembly Depth DepthRemoving/Installing the Shrouds SHROUD/WHEELSReplacing the Flat Free Tires on the Wheel Rim SHROUD/WHEELSRemoving/Installing the Shrouds Engaging/Disengaging Motor Release Lever Engaging/Disengaging Motor Release LeverAdjusting Forks Replacing Front/Rear Caster AssembliesBatteries BatteriesInstalling/Removing the Batteries Tool QTY CommentsBatteries with/without Lifting straps Tie Wrap Connecting/Disconnecting the Battery Wiring Harness Connecting/Disconnecting the Battery Wiring Harness SPJ+ Joysticks When to Charge BatteriesMPJ+ Joystick Charging Batteries Battery Charger Operation On-Board Battery ChargerIndependent Charger To Wall OutletRequired Items Tool QuantityTransport Ready Package Transport Ready PackageSpecifications Wheelchair Weight LimitAbout Transport Ready Packages Compliance InformationSecuring the Wheelchair to the Vehicle Positioning the Wheelchair in the VehicleSecurement Points Securing the WheelchairSecuring the Occupant Wheelchair-Anchored BeltsVehicle-Anchored Belts Seating SystemPositioning Belts Positioning BeltsPronto M91Base with SureStep Global Limited Warranty Excluding Canada Global Limited Warranty Excluding CanadaCanada Limited Warranty USA