Toshiba SL-9000N-FFR-US, EO1-31001 Weighing Operation, Menu REG., M.DOWN, or Rewrap Mode Weigh

Page 67

14. OPERATING PROCEDURES

14.2 FIX PRICE OPERATION (FOR US TYPE ONLY)

14.1 WEIGHING OPERATION

Menu: REG., M.DOWN, or REWRAP

Mode: WEIGH

The weigh mode is used to weigh a commodity and to issue the label. The label contains data such as a weight, unit price (price per weight) and total price (calculated as a result of the weighing operation). The following is a basic operation seen at the sales floor of a store or at a back room where different kinds and weights of commodities are repacked. Pressing the [VOID] key subtracts the last entry from the memory.

Example) When PLU #100 and an unit price of $8.00 are set in the speed key #12.


Enter the PLU #.	1	0		0

Press : PLU

LB

kg

	Press the	12
	speed key.	12
	speed key.

The unit of measure can be changed for CA model only.

LB ↔ kg

Available only when the initial setting # 5-6 is set to 1.

lb scale

kg scale

100 g	1/4	1/2

Place a commodity on the platter.

(Ex. 1.000 lb.)

MANUAL :	:	AUTO
	*

The label is issued

Press when canceling	VOID
the last sales.

<REG.> MANU. WEIGH

T-BONE STEAK

	lb	UNIT/$	TOTAL $
	1.000	8.00	8.00

TEC STORE

(TEL) 0123-45-6789

(Sample label)

NOTES:

1. Pressing a speed key to which no PLU data has been assigned will result in an error.


	In this case, press the					C	key, then press a speed key to which PLU data has been assigned.
2.	To change between AUTO and MANUAL, follow the procedure provided in section 14.9.
3.	If a unit price exceeding 4 digits is obtained by multiplying by 2 or 4 (when pressing the								1/2 lb	key or
	1/4 lb	key), the unit price will be 0.
	1/4 lb

4.	100 g	key is available only when the scale is a kg scale or operated on kg base.
								key is pressed, the unit price does change on the display.
5.	When the		1/2 lb	,	1/4 lb	or	100 g	key is pressed, the unit price does change on the display.

6.When the “compulsory tare” is selected, a tare must be subtracted in a weighing operation, otherwise an error message “TARE REQUIRED” will be displayed when the following operation has been done:

① Manual mode: Pressing the PRT/* key.

②Auto mode: Placing a commodity on the platter.

③ Floating vendor mode: Pressing the Vendor key.

When a “TARE REQUIRED” is displayed, refer to Section 14.6 to follow the proper weighing procedure.

14- 2

Image 67

Contents SL-9000/9000N-FFR-US/CA/QR Page Safety Summary Precautions Table of Contents 14.2 13.113.2 14.1Introduction Applicable Model AccessoriesScale SpecificationTmcc OptionLON STLAN-2PLevel Gauge Label Guide Printer Cover Main Power SwitchAdjustable Legs Meat Platter Power Cord AppearanceUS Type DisplayCA/QR Type Programming Keyboard KEY LayoutProgramming Keyboard Function Send SpaceProg Operation Keyboard Function Operation Keyboard and Speed KeyboardPLU Void PRTFor DT/TMZero Self Service KeyboardKEY Layout Speed KEY SET Procedure Before OperationInstallation Procedure Level Adjustment Removal and Replacement of Media Removal and Replacement of Media Outline of Operation PowerTmcc CMT-port communicarion Clerk Label Registration modeXNOT Available 1/4LB KEY 100g, kg KEY LB/kg KEYHow to access to Programming Menu Programming ProceduresTitle and Contents of Programming Menu TEC Store How to enter charactersMenu PLU Data EditSet tare limit PLU Data SettingAuto Code Ingredient Message Nutrition Setting When entering PLU#, be careful of the following Set the Daily Value Table Daily Value Max digits Contents of Daily valueDeleting Nutrition Data Memory file is sorted when a memory full error occursMemory file sort Menu Item No Verifies PLU data stored in the scale PLU Verifying LabelAddress and Commercial Message Setting Message construction Message display time Combination MessageThank YOU ANK YOU Call AGA Scrolling Flashing Curtaining Scrolling up Scrolling downThank YOU Thank YOU CallGrade Line Special InformationVendor Number Speed KEY SettingSetting Department/Vendor Number Department NumberBy pressing Key Print FormatFormat No Label Format Number TableMenu Item No DATE/TIME SettingCMT Operations PL-3 Operation Error code during PL-3 operationItem # Transmission Item ListCMT IN-LINE/LOCAL Transmission Delay Time TableLON System Initial #0 #19, SL-9000N only Cancel Retry ContinueData Transmission Price Address SL-9000N only② By Count Format Default Bar Code FormatBAR Code Format ① Weigh or Fix Price FormatPLU # UPC # PC/D Flag PLU # UPC # PC/D Price WeightAdditional 234 235 Additional 7,8 238 Additional 9,10 239 Title No Format Additional 221Additional 231 232 Additional 233SL-9000N only Transferring Logo DataVerify SL-9000=CMT Error message during data transmission Idiom SettingVendor Setting Key functions Free Format SettingEnter SP-INFO/NET WT Logo Frequent Shopper Print coordinate Programmed Data Verification Reports How to access Report menuMenu Set the zone PLU #. Ex. PLU #100 ～108 R S X Z Password SecuritySetting Password and Protect Menu R S× ー × Calling Menu by Entering Password How to access REG., M.DOWN, or Rewrap menu Operating ProceduresWeighing Operation Menu REG., M.DOWN, or Rewrap Mode WeighFIX Price Operation for US Type only By Count Operation For To check the remaining number, clear the PLU and press Key Print Count OperationExample B When operating in Fix or By Count mode Set the number of labels. Max labels Enter the PLU # PLU Issuing Labels with NET Weight Statement for US Type onlySample label 14-10 TARE/SAVE Function Procedures Calling and Printing Grade Lines Logo Calling and Printing LogosSelecting Print Item Menu REG, M.DOWN, or Rewrap Mode WEIGH, FIX, or by CountDate Change Batch Print Mode with 30 Items Run Assignment Unit Price Change and G.Line/LOGO Call Key Label Issue Stop or CancelTotals Overflow error occurs when Key is pressed to issueDpt # Visual Commodity LibraryFloating Vendor Subtotal Price deletionTotal Operation How to access Read or Reset menuEx. Report Menu Hourly Total ReportGrand Total Report PLU Total ReportFor Enter PLU Total Vendor Total ReportProgramming Mode Error Message TableReport and Reset Mode Label lssue ModeLON System Mode Cleaning the Print Head Before You Call for Service Troubleshooting