Delta DT3 instruction sheet Programmable Waiting Setting range 0~1000100.0 Temeprature

1103H	Reverse Output	Bit1: output 2, Bit0: output 1
1104H	Slope of Temperature Increase	Unit: 0.1℃/min or 0.1℃/sec (refer to CommunicationAddress 1124H)
1105H	Remote Input Type Selection	0: 0~20m A , 1: 4~20m A, 2: 0~5V, 3: 1~5V, 4: 0~10V
1106H	AT Control	0: AT(Auto-tune), 1: ST(Self-tune)
1107H	Remote Input Reverse Setting	0: forward, 1: reverse
1108H	Alarm 1 Function Selection	Bit3: Peak Record, Bit2: Hold Enable, Bit1: Output Reverse, Bit0: Standby Enable
1109H	Alarm 2 Function Selection	Bit3: Peak Record, Bit2: Hold Enable, Bit1: Output Reverse, Bit0: Standby Enable
110AH	Alarm 3 Function Selection	Bit3: Peak Record, Bit2: Hold Enable, Bit1: Output Reverse, Bit0: Standby Enable
110BH	Alarm 1 Output Delay Time	Unit: second. Setting range: 0~100sec
110CH	Alarm 2 Output Delay Time	Unit: second. Setting range: 0~100sec
110DH	Alarm 3 Output Delay Time	Unit: second. Setting range: 0~100sec
110EH	Upper Limit of Control Output 1	Range: lower limit of control output ~100%, unit is 0.1%
110FH	Lower Limit of Control Output 1	Range: 0~upper limit of control output, unit is 0.1%
1110H	Upper Limit of Control Output 2	Range: lower limit of control output~100%, unit is 0.1%
1111H	Lower Limit of Control Output 2	Range: 0~upper limit of control output, unit is 0.1%
1112H	Programmable Waiting	Setting range: 0~1000(100.0℃)
	Temeprature
1113H	Programmable Waiting Time	Unit: min. Setting range: 0~900
1114H	Programmable Slope Increase	Unit: 0.1℃/min or 0.1℃/sec--- (refer to Communication Address 1124H) Setting
		range: 0~1000
1115H	Testing Mode
1116H	Adjust Upper Limit of Analog	Adjust current: 1scale=1μA, Adjust voltage: 1scale=1mV
	Linear Output 1
1117H	Adjust Lower Limit of Analog	Adjust current: 1scale=1μA, Adjust voltage: 1scale=1mV
	Linear Output 1
1118H	Adjust Upper Limit of Analog	Adjust current: 1scale=1μA, Adjust voltage: 1scale=1mV
	Linear Output 2
1119H	Adjust Lower Limit of Analog	Adjust current: 1scale=1μA, Adjust voltage: 1scale=1mV
	Linear Output 2
111AH	Adjust Retransmission Upper	Adjust current: 1scale=1μA
	Limit
111BH	Adjust Retransmission Lower	Adjust current: 1scale=1μA
	Limit
111CH	Event 1 Selection	0: OFF, 1: Run/Stop, 2: Change SV value, 3: PID/Manual control, 4: Switch to
		Programmable Hold mode
111DH	Event 2 Selection	0: OFF, 1: Run/Stop, 2: Change SV value, 3: PID/Manual control, 4: Switch to
		Programmable Hold mode
111EH	Event 3 Selection	0: OFF, 1: Run/Stop, 2: Change SV value, 3: PID/Manual control, 4: Switch to
		Programmable Hold mode
111FH	PV Control Mode Selection	0: PID, 1: ON/OFF, 2: Manual control, 3: Fuzzy
1120H	SV Control Mode Selection	0: Constant, 1: Slope increase, 2: Programmable input, 3: Remote Input
1121H	Adjust Remote Compensation	Setting range: -999~999
1122H	Adjust Remote Gain	Setting range: -999~999
1123H	Positive/Negative Selection for	0: Positive, 1: Negative
	Remote
1124H	Switch Slope Time Unit	0: min, 1: sec
1125H	Cold Junction Compensation	0: ON, 1: OFF
1126H	Reserve the Programmable	0: None, 1: Running status is saved and will continue by the previous status when
	Running Status when Power OFF	power ON.
1127H	Fuzzy Gain	Setting range: 1~10
1128H	Fuzzy Dead Band	Setting range: 0.0~PB
1129H	Save Programmable Settings	0:None, 1: Saves the programmable settings into memory
	into Memory
1182H	CT1 Read Value	Unit: 0.1A
1183H	CT2 Read Value	Unit: 0.1A
1. Address and Content of Bit Register: First bit of reading will put into LSB. Write data= FF00H for bit set, 0000H for bit clear.
0810H	Read AT LED status	0: OFF(default), 1: ON
0811H	Temperature unit display	0: ℉, 1: ℃ / linear input (default)

19